VIPER22 APPLI Search Results
Documents mentioning VIPER22 APPLI
| Document | Partial File Text | Tags | Type | |||
|---|---|---|---|---|---|---|
| viper53 | STEVAL-ISA009V1 VIPer53-E single output reference design board with 90 to 264 VAC input and 24 W output Data Brief Features ■ Switch-mode general-purpose power supply ■ Current mode control with adjustable limitation ■ 75% efficiency ■ Output short-circuit and overload protection |
Original | ||||
| steval-isa004v1 | STEVAL-ISA004V1 VIPer22A-E dual-output evaluation board with 90 to 264 VAC input and 10 W output Data Brief Features ■ Switch-mode general-purpose power supply ■ Input: 90 to 264 VAC 50/60 Hz ■ Output: 12 V @ 0.42 A and 5 V @ 1 A ■ Burst-mode operation in standby for Blue |
Original | ||||
| an2359 | AN2359 Application note Double output Buck-Boost converter with VIPerX2A Introduction This paper introduces two off-line non-insulated SMPS double outputs in Buck–Boost configuration based on VIPerX2A family The power supplies are operated in wide input |
Original | ||||
| an2097 | AN2097 APPLICATION NOTE VIPower: 10W POWER SMPS USING VIPer22A FOR AIR-CONDITIONER APPLICATION 1. ABSTRCT New air-conditioner systems use two main lowvoltage outputs to supply the internal electronic equipment, respectively these values are +12V and +5V. These low output voltages are generated |
Original | ||||
| STEVAL-ISA009V1 VIPer53-E single output reference | STEVAL-ISA009V1 VIPer53-E single output reference design board with 90 to 264 VAC input and 24 W output Data Brief Features ■ Switch-mode general-purpose power supply ■ Current mode control with adjustable limitation ■ 75% efficiency ■ Output short-circuit and overload protection |
Original | ||||
| Evaluation boards STMicroelectronics application | Evaluation boards STMicroelectronics application support September 2007 www.st.com/evalboards If you want to evaluate ST’s microcontrollers, power and analog product families for use in your new design, check out ST’s new selection of evaluation boards. These tested and qualified application boards are ready-to-go solutions for |
Original | ||||
| an1736 | AN1736 Application note VIPower: VIPer22A dual output reference board 90 to 264 VAC input, 10W output Introduction This is an off-line wide range VIPer22A dual outputs power supply at a switching frequency of 60kHz and is set up for secondary regulation with an optocoupler. One output delivers 5V |
Original | ||||
| rd-166 | National Semiconductor RD-166 Product Applications Design Center December 2008 1.0 Design Specifications Inputs Output #1 VinMin=100V Vout1=5V VinMax=240V Iout1=0.5A 2.0 Design Description Preface Every year, millions of Watts are lost in heat from inefficient |
Original | ||||
| Demonstration boards STMicroelectronics | Demonstration boards STMicroelectronics application support September 2008 www.st.com/evalboards STMicroelectronics proposes a wide range of demonstration boards that may be used to perform a comprehensive evaluation of ST’s products and solutions while reducing your development time. |
Original | ||||
| Demonstration boards STMicroelectronics | Demonstration boards STMicroelectronics application support May 2009 www.st.com/evalboards Contents Product demonstration boards 4 Audio ICs 4 Power management ICs 5 Motion sensors (MEMS) 7 RF power 8 Motor control ICs 8 Lighitng ICs 9 Communication and connectivity ICs |
Original | ||||
| an2544 | AN2544 Application note Designing a low cost power supply using a VIPer12/22A-E in a buck configuration Introduction Many appliances today use nonisolated power supply to furnish low output power required to run a micro, LED display, and a few relays or AC switches. This type of power supply has |
Original |