DCAN Search Results

2324w

Contextual Info: Application Guide DCAN-9 VKP Rev C 3/2002 VKP60xT/VKP100MT APPLICATION NOTES Output Configurations The VKP60xT/VKP100MT series DC/DC converters provide three outputs to match the needs of many popular multi-output and multi-channel applications. Because each of the

DC-DC Converter Burr-Brown 700

Abstract: Variable resistor 10K ohm potentiometer 10K potentiometer AD558 Variable resistor 10K ohm pot Potentiometer 10k voltage rating 10 k, 10 turn potentiometer, trim 1 ohm variable resistor 500 watt potentiometer trim 10k OPA 339
Contextual Info: Application Note www.murata-ps.com Different Ways to Adjust the Output Voltage of the VKA DC to DC Converter Family DCAN-33 by Barry Ehrman All VKA Series DC-DC converters incorporate output voltage trim capability. Most models’ output voltages can be adjusted within the range of -50% to

Contextual Info: Application Guide DCAN-12 Thermal Derating The above power derating curve can be used for all C&D Technologies’ DC to DC converters that are less than 25 Watts and that do not otherwise specifiy power derating above maximum specified temperature. Typically, heat sinking and fan cooling are not

P0351

Abstract: VSX60MD35-1 400 volt fuse
Contextual Info: DCAN-40 REV F Application Guide DCAN-40 Rev F VSX60 & VSX75 APPLICATION NOTES By Barry Ehrman, Applications Engineer The VSX60 Series and VSX75 Series are 60 Watt and 75 Watt, respectively, dual output converters with 18-36V VSX60 only and 36-75V input models with 3.3VDC and 5VDC

bosch can 2.0B

Abstract: DPRAM FLEX10KE BOSCH CAN vhdl Bosch can Bosch d_can Bosch APEX20K APEX20KC APEX20KE
Contextual Info: DCAN Configurable CAN Bus Controller ver 1.01 ● Last Error Code The DCAN is a stand-alone controller for the Controller Area Network CAN widely used in automotive and industrial applications. DCAN conforms to Bosch CAN 2.0B specification (2.0B Active). Core has simple CPU interface

VKA100MS05

Abstract: Toroidal transformer
Contextual Info: Application Guide DCAN-44 V Series DC to DC Converter Ripple Reduction Circuit By Barry Ehrman Applications Engineer The following filter circuit can reduce the output ripple of a fully loaded VKA100MS05 from 200 millivolts peak to peak to 10 millivolts peak to peak. This circuit will work on

DCAN-15

Contextual Info: Application Guide DCAN-15 Calculation of Leakage Current The leakage current associated with an AC/DC converter is typically measured through a resistor connected to earth ground. Since DC/DC converters are not connected to line voltage, however, the leakage current is measured from the primary and secondary

Murata

Contextual Info: Application Note Subranging ADCs Operate at High Speed with High Resolution DCAN-5 For full details go to www.murata-ps.com/rohs www.murata-ps.com Technical enquiries email: sales@murata-ps.com, tel: +1 508 339 3000 DCAN_06_AppNote Page 1 of 10 Application Note

2N2222 circuit

Abstract: 2N2222 r4 2N2222 2N2907 2N2222 application note Q1 2N2222 Datasheet 2N2222 transistor TIP41C TIP41C EQUIVALENT
Contextual Info: DCAN-29 Application Guide Active Voltage Ramp Circuit By Barry Ehrman Applications Engineer The following circuit can be used to control input voltage rise times to sensitive DC to DC converters. The component values shown will give a total linear voltage rise time of

EN55022

Abstract: CD43-1ROMC DCAN 56uF wpn20r AC input filter Capacitor ripple noise Measurements capacitor 100uF 100V
Contextual Info: Application Guide DCAN-43 WPN20R APPLICATION NOTES By Richard Donnelly, Applications Engineer These application notes provide information on the input reflected ripple current, EMI, and output ripple/noise characteristics of the WPN20R series of DC/DC converters. These notes are designed to supplement the data sheet and

Contextual Info: Preliminary Product Overview DCAN250 - CAN over Powerline Communication This information is preliminary and may be changed without notice. 1. General The DCAN250 was designed to transfer CAN messages over noisy DC Power Line using the DCBUS1 technology. It enables a new physical layer of CAN network for communication between

Tantalum Capacitor 25v

Abstract: capacitor 25v filtering DCAN
Contextual Info: DCAN-30 Application Guide Low Cost HPRxxx Output Ripple Filters By Barry Ehrman Applications Engineer The circuits shown below will reduce the 45 mV p-p voltage ripple that is common on the output of the HPR family to 2 mV p-p. The filter works by shunting the high frequency noise to earth ground through C1 capacitor and using a low cost LC

WYO102MCMBFOK

Abstract: WYO502MCMCFOK 475K100CS4 ECE-A2AGE330 VKA100MS12 roederstein capacitor tantalum
Contextual Info: Application Guide DCAN-38 VKA APPLICATION NOTES By Barry Ehrman Applications Engineer The VKA Series is a family of 50 to 150 Watt DC to DC converters designed to present an economical and practical solution for distributed architectures. All members of this family

Contextual Info: Application Note Output Capacitive Load Considerations DCAN-58 By Larry Copeland There are numerous factors to consider when adding external capacitors to switched-mode power supplies SMPS . This article will discuss noise, startup, ESR, stability, pre-bias applications, Sense inputs, On/Off (remote enable)

Contextual Info: Application Guide DCAN-34 6 PAK Demo Board By Barry Ehrman Applications Engineer The 6 PAK Demo Board, part number AS-354, is a 4” x 4” printed circuit board designed to easily demonstrate how one 6-PAK Controller plus up to eight 6-PAK Boost Sips can

P0351

Abstract: VSX60MD35-1
Contextual Info: DCAN-40 REV F Application Guide DCAN-40 Rev F VSX60 & VSX75 APPLICATION NOTES The VSX60 Series and VSX75 Series are 60 Watt and 75 Watt, respectively, dual output converters with 18-36V VSX60 only and 36-75V input models with 3.3VDC and 5VDC outputs. The VSX60 and VSX75 converters are packaged in the industry quarter-pak size

VKA100MS05-1

Abstract: VKA100MS05
Contextual Info: Application Guide DCAN-48 Using VKA-1 Models in Standard VKA Applications VKA converters are available in two different versions: the standard version i.e. VKA100MS05 and the “–1” (i.e. VKA100MS05-1). The only difference between these two versions is the logic polarity of the primary “On/Off”

Contextual Info: PRELIMINARY PRODUCT INFORMATION_ / MOS INTEGRATED CIRCUIT / /IP D 7 8 F 0 7 0 1 Y 8-BIT SINGLE-CHIP MICROCONTROLLER The ,uPD78F0701 Y is a ,uPD780701Y sub-series product of the 78K/0 series. DCAN controller and an lEBus TM The ,uPD78F0701 Y features a

uPC2590

Abstract: uPD78F0701Y PD780208 PD78044F pd780973 uPD780701Y uPD78070A uPD78075B uPD78078 uPD78F0701YGC-8BT
Contextual Info: PRELIMINARY PRODUCT INFORMATION MOS INTEGRATED CIRCUIT µPD78F0701Y 8-BIT SINGLE-CHIP MICROCONTROLLER The µPD78F0701Y is a µPD780701Y sub-series product of the 78K/0 series. The µPD78F0701Y features a TM DCAN controller and an IEBus controller. It also features flash memory as internal ROM. Programs can be written

VKP60MT312

Abstract: VKP60MT 2324w DCAN-9
Contextual Info: Application Guide DCAN-9 VKP60xT APPLICATION NOTES Output Configurations The VKP60xT series DC/DC converters provide three outputs to match the needs of many popular multi-output and multi-channel applications. Because each of the three channels is individually isolated and current limited, these devices may be easily configured in a

uPD780701Y

Abstract: uPD780702Y uPD78F0701Y U12326E UPD780701YGC-8BT Bosch d_can
Contextual Info: PRELIMINARY PRODUCT INFORMATION MOS INTEGRATED CIRCUIT µPD780701Y, 780702Y 8-BIT SINGLE-CHIP MICROCONTROLLER DESCRIPTION The µPD780701Y and 780702Y are the µPD780701Y Subseries products of the 78K/0 Series. microcontrollers have DCAN controller µPD780701Y , IEBus

HL02R05S05

Abstract: HL02R
Contextual Info: Application Guide DCAN-19 Effects of Lead Resistances on Load Regulation Parmeter Line Regulation Load Regulation Conditions High Line to Low Line Rated Load to No Load Min Typ +0.5 +0.1 Max +1.0 +0.5 Units % % When the load regulation is specified for a DC/DC converter, it is assumed to be

DC TO DC

Abstract: HB04U15D15Q WP05R24D15 WP06R48S05N WPC10R24S05N WPC10R HB04U1
Contextual Info: DCAN-31 Application Guide Output Ripple Filter By Barry Ehrman Applications Engineer The following is a general purpose ripple filter circuit that can reduce voltage ripple on some DC to DC converters up to 27db. SINGLE OUTPUT C1, C2 C3 L1, L2 = 3000 pF Ceramic Capacitor

PLZ1003W

Abstract: EMPRO shunt resistor resistor testing using multimeter TB3B TDS-640A testing resistor using multimeter HP 3458A current shunt
Contextual Info: DCAN-56 EQEVAL-1 DC/DC Converter Evaluation Board Application Note INTRODUCTION The EQEVAL-1 DC/DC converter evaluation board is designed to test and verify the functional performance of C&D’s industry standard single output eighth brick, quarter brick and intermediate bus DC/DC converters. The evaluation board