Part Number
    Please enter a valid full or partial manufacturer part number with a minimum of 3 letters or numbers

    VJ0805S Search Results

    Documents mentioning VJ0805S

    Document Partial File Text Tags Type PDF
    mic2193
    Application Hint 70 MIC2193 3.3V to 2.5V/5A with Ceramic Cout Application Circuit By Steven Chenetz General Description The MIC2193 is a 400kHz Synchronous Buck controller that uses a P-channel high-side FET. It has the advantage of running at 100% duty cycle (high-side Fet
    Original PDF
    National Semiconductor Application Note 1208 July
    National Semiconductor Application Note 1208 July 2001 Notes 4. The board shuts down after a VID bit is toggled on the DIP switch; Do not change the Ch1 voltage setting on the fly using the DIP switch. Instead, set the corresponding DIP VID bits to float, and then use a signal generator to toggle the
    Original PDF
    mic2198
    MIC2198 Evaluation Board Micrel MIC2198 Evaluation Board 500kHz SO-8 Synchronous Buck Control IC Introduction Quick-Start Guide Refer to Figure 1 for the following: 1. Connect the positive terminal from the power supply to VIN post (J1) on the MIC2198 evaluation board.
    Original PDF
    mic2194
    MIC2194 Evaluation Board Micrel MIC2194 Evaluation Board 400kHz SO-8 Buck Control IC Introduction Quick-Start Guide Refer to Figure 1 for the following: 1. Connect the positive terminal from the power supply to VIN post (J1) on the MIC2194 evaluation board.
    Original PDF
    mic2198
    MIC2198 Evaluation Board Micrel MIC2198 Evaluation Board 500kHz SO-8 Synchronous Buck Control IC Introduction Quick-Start Guide Refer to Figure 1 for the following: 1. Connect the positive terminal from the power supply to VIN post (J1) on the MIC2198 evaluation board.
    Original PDF
    National Semiconductor Application Note 1208 July
    National Semiconductor Application Note 1208 July 2001 NOTES 1. When a DIP switch slide is ON, the signal whose label appears beside that slide is grounded; 2. Much flexibility is built into the board. For example, it is possible to use a dual SO-8 FET in Ch2, it is possible to
    Original PDF
    mic2196
    MIC2196 LED Driver Evaluation Board Boost LED Driver w/PWM DIM Control General Description The MIC2196 current mode boost controller is used to implement a LED Driver with PWM DIM control (Figure 1). The LED series string is pulsed on and off by the PWM DIM input signal to provide true PWM dimming. When
    Original PDF
    mic2196
    MIC2196 Evaluation Board Micrel MIC2196 Evaluation Board 400kHz SO-8 Boost Control IC Quick-Start Guide Refer to Figure 1 for the following: 1. Connect the positive terminal from the power supply to VIN post (J1) on the MIC2196 evaluation board. 2. Connect the GND terminal of the input power
    Original PDF
    mic2196
    Application Note 53 180 Watt Boost Converter By Mark Ziegenfuss General Description The MIC2196 controller is used to implement a non26V (set by the R3 and R10 divider). The output current is isolated boost converter (Fig. 1). A boost converter has a 7 amps max. The maximum input voltage to the MIC2196
    Original PDF
    mic2196
    MIC2196 CUK Evaluation Board Micrel MIC2196 CUK Evaluation Board 400kHz SO-8 CUK Introduction Quick-Start Guide Refer to Figure 1 for the following: 1. Connect the positive terminal from the power supply to VIN post (J1) on the MIC2196 CUK evaluation board.
    Original PDF
    mic2199
    MIC2199 Evaluation Board Micrel MIC2199 Evaluation Board 300kHz SO-8 Synchronous Buck Control IC Introduction Quick-Start Guide Refer to Figure 1 for the following: 1. Connect the positive terminal from the power supply to VIN post (J1) on the MIC2199 evaluation board.
    Original PDF
    mic2196
    MIC2196 SEPIC Evaluation Board Micrel MIC2196 SEPIC Evaluation Board 400kHz SO-8 SEPIC Demo Manual Introduction Quick-Start Guide Refer to Figure 1 for the following: 1. Connect the positive terminal from the power supply to VIN post (J1) on the MIC2196 SEPIC
    Original PDF
    mic2193
    MIC2193 Evaluation Board Micrel MIC2193 Evaluation Board 400kHz SO-8 Synchronous Buck Control IC Introduction Quick-Start Guide Refer to Figure 1 for the following: 1. Connect the positive terminal from the power supply to VIN post (J1) on the MIC2193 evaluation board.
    Original PDF