RUBADUE Search Results
Documents mentioning RUBADUE
| Document | Partial File Text | Tags | Type | |||
|---|---|---|---|---|---|---|
| National Semiconductor Application Note 1613 | National Semiconductor Application Note 1613 Jason Rubadue April 2007 Theory and Purpose resolutions, refresh rates and color depths continue to increase and so do the required data rates, currently at 1.65Gbps for DVI 1.0 and HDMI 1.2a, increasing to 3.4Gbps |
Original | ||||
| National Semiconductor Application Note 1613 | National Semiconductor Application Note 1613 Jason Rubadue, Winston Wong October 16, 2009 Theory and Purpose resolutions, refresh rates and color depths continue to increase and so do the required data rates, at 1.65 Gbps for DVI 1.0 and upto 3.4 Gbps for HDMI 1.3a. Unfortunately, the |
Original | ||||
| sge2649-2 | Magnetic Component Specification 1.0 Specification Number SGE2649-2 Rev.E (063004) Document Scope. This document describes the attributes of an electronic high-frequency current transformer for end-use in DC to AC inverters that operate between 35 kHz and 100 kHz. This document is intended to be a binding specification of this current transformer to include (but not limited to) mechanical |
Original | ||||
| topswitch | ® TOPSwitch® Power Supply for Echelon® PLT-21 Power Line Transceiver Design Note DN-15 Introduction A TOPSwitch power supply is ideally suited to power the Echelon PLT-21 power line transceiver control node. TOPSwitch requires 50% fewer components compared with a discrete |
Original | ||||
| topswitch | ® TOPSwitch Power Supply for Echelon® PLT-20 Power Line Transceiver Design Note DN-13 Introduction A TOPSwitch power supply is ideally suited to power the Echelon PLT-20 power line transceiver control node. TOPSwitch requires 50% fewer components compared with a discrete |
Original | ||||
| sge2649-2 | Magnetic Component Specification 1.0 Specification Number SGE2649-2 Rev.E (063004) Document Scope. This document describes the attributes of an electronic high-frequency current transformer for end-use in DC to AC inverters that operate between 35 kHz and 100 kHz. This document is intended to be a binding specification of this current transformer to include (but not limited to) mechanical |
Original | ||||
| top224y | Flyback Transformer TOP224Y/TOP225Y Turns Ratio Bias (3-4) : Primary (2-1) Sec. #1 (8-7) : Primary (2-1) Sec. #2 (6-5) : Primary (2-1) PARAMETER Primary Inductance (2-1) Pri. Leakage Ind.1 1 1 : 8.375 + 4% 1 : 4.250 + 4% 1 : 4.250 + 4% MIN. TYP. MAX. UNITS |
Original | ||||
| National Semiconductor Application Note 918 | National Semiconductor Application Note 918 Richard Frank Hendrik Santo Thomas Szepesi January 1994 1 0 INTRODUCTION In isolated DC DC converters the output voltage is controlled either via a tertiary winding on the main flyback transformer or via direct feedback from the secondary side If |
Original | ||||
| application notes | HOME APPLICATION NOTES Practical Construction Tips For Coils Using Iron Powder Cores Presented by Dale Nicol Micrometals, Inc. APEC ‘96 San Jose, California March 5th, 1996 (Revised April 2, 2001) The purpose of the following discussion is to convey practical application information for coil |
Original | ||||
| flyback transformer design | APPLICATION NOTE AN-1024a International Rectifier • 233 Kansas Street El Segundo CA 90245 USA Flyback Transformer Design For The IRIS40xx Series By Jonathan Adams TOPICS COVERED Introduction To Flyback Transformer Design Power Supply Design Criteria Required |
Original | ||||
| ஃࢅణڦ āāDVIࢅHDMIፌ؛ᆩઠሞ܌ਐฉدೕࢅຕLj | ஃࢅణڦ āāDVIࢅHDMIፌ؛ᆩઠሞ܌ਐฉدೕࢅຕLj ഄዐۉમࡼڦᆖၚᅜࢮăܸLjᆶႹܠᆌᆩᄲ൱ ֑ᆩ߸ۉڦમLj૩සॽऺ໙ऐೌدໃᇺײ၂๖ࢅ |
Original | ||||
| flyback transformer design | Application Note AN-1024 Flyback Transformer Design for the IRIS40xx Series Table of Contents Page 1. Introduction to Flyback Transformer Design… 1 2. Power Supply Design Criteria Required… 2 |
Original |