AN1089 ST Search Results
Documents mentioning AN1089 ST
| Document | Partial File Text | Tags | Type | |||
|---|---|---|---|---|---|---|
| an1089 | AN1089 APPLICATION NOTE ® CONTROL LOOP MODELING OF L6561-BASED TM PFC by Claudio Adragna This paper provides a model and a tool for evaluating and improving the control loop characteristics of L6561-based PFC preregulators in boost topology and operated in Transition Mode (TM). |
Original | ||||
| an1757 | AN1757 APPLICATION NOTE SWITCHING FROM THE L6561 TO THE L6562 by Luca Salati 1 INTRODUCTION Conceived on the same core of the L6561 and pin-to-pin compatible with it (see fig. 1), the L6562 is the new ST's Transition Mode (TM) controller for high Power Factor Corrector stages: the replacement can be done with |
Original | ||||
| isl4089 | ISL4089 ® Data Sheet June 28, 2006 FN6192.1 DC-Restored Video Amplifier Features The ISL4089 is complete DC-restored monolithic video amplifier sub-system. It contains a high performance video amplifier and a nulling, sample-and-hold amplifier designed to establish a programmable DC output level. |
Original | ||||
| l6561 | AN1214 APPLICATION NOTE DESIGN TIPS FOR L6561 POWER FACTOR CORRECTOR IN WIDE RANGE by Cliff Ortmeyer & Claudio Adragna This application note will describe some basic steps to optimize the design of the L6561 PFC for wide range voltage input (105V- 300V) while also having a broad output power range (65W - 105W). Initial |
Original | ||||
| an1616 | AN1616 APPLICATION NOTE THD-OPTIMIZER CIRCUITS FOR PFC PRE-REGULATORS by Claudio Adragna Although THD (Total Harmonic Distortion) is not explicitly considered in IEC 61000-3-2 standards, neither it needs to be very low in order for a piece of equipment to get the presumption of conformity, however it has become established to require an ultra-low THD in some applications such as electronic |
Original | ||||
| AN966 APPLICATION NOTE L6561, ENHANCED | AN966 APPLICATION NOTE L6561, ENHANCED TRANSITION MODE POWER FACTOR CORRECTOR by Claudio Adragna The TM (Transition Mode) technique is widely used for Power Factor Correction in low power applications, such as lamp ballasts or low-end monitors. The L6561 is the latest ST’s proposal for this |
Original | ||||
| an966 | AN966 APPLICATION NOTE L6561, ENHANCED TRANSITION MODE POWER FACTOR CORRECTOR by Claudio Adragna The TM (Transition Mode) technique is widely used for Power Factor Correction in low power applications, such as lamp ballasts or low-end monitors. The L6561 is the latest ST’s proposal for this |
Original | ||||
| isl59451 | ISL59451 IGNS E W DES N R O F N DED EM ENT COMME RE PL AC D E N OT R E D N E enter at OM M Data Sheet port C p u S l NO R E C a m/tsc nic our Tech r www.intersil.co t c ta n o c o TERSIL 1-888-IN ® September 24, 2007 Triple 4:1 DC Restored Single Supply Video Multiplexing Amplifier |
Original | ||||
| an3009 | AN3009 Application note How to design a transition mode PFC pre-regulator using the L6564 Introduction The transition mode (TM) technique is widely used for power factor correction in low and medium power applications, such as lamp ballasts, high-end adapters, flatscreen TVs, |
Original | ||||
| an3009 | AN3009 Application note How to design a transition mode PFC pre-regulator using the L6564 Introduction The transition mode (TM) technique is widely used for power factor correction in low and middle power applications, such as lamp ballasts, high-end adapters, flat-screen TVs, |
Original | ||||
| an2761 | AN2761 Application note Solution for designing a transition mode PFC preregulator with the L6562A Introduction The TM (transition mode) technique is widely used for power factor correction in low and middle power applications, such as lamp ballasts, high-end adapters, flat TVs and monitors, |
Original | ||||
| an2782 | AN2782 Application note Solution for designing a 400 W fixed-off-time controlled PFC preregulator with the L6562A Introduction In addition to the transition mode (TM) and fixed-frequency continuous conduction mode (FF-CCM) operation of PFC pre-regulators, a third approach is proposed that couples the |
Original | ||||
| an2782 | AN2782 Application note Solution for designing a 400 W fixed off-time controlled PFC pre-regulator with the L6562A Introduction In addition to the transition mode (TM) and fixed-frequency continuous conduction mode (FF-CCM) operation of PFC pre-regulators, a third approach is proposed that couples the |
Original | ||||
| an3027 | AN3027 Application note How to design a transition-mode PFC pre-regulator with the L6563S and L6563H Introduction The transition-mode (TM) technique is widely used for power factor correction in low and middle power applications such as lamp ballasts, high-end adapters, flatscreen TVs and |
Original | ||||
|
|
||||||
| an3027 | AN3027 Application note How to design a transition-mode PFC pre-regulator with the L6563S and L6563H Introduction The transition-mode (TM) technique is widely used for power factor correction in low and middle power applications such as lamp ballasts, high-end adapters, flatscreen TVs and |
Original | ||||