01SEP2008 Search Results

Contextual Info: 4 THIS DRAWING IS UNPUBLISHED. C COPYRIGHT 20 RELEASED FOR PUBLICATION LOC AL ALL RIGHTS RESERVED. BY - 20 2 3 1 REVISIONS DIST 2 P E TYPICAL APPLICATION D F F1 DATE DWN APVD CHANGED PCB LAYOUT 01SEP2008 J.S. G.T. DELETED PART REVISION TABLE 18MAR2009 JS PEG

ST7FMC2S4T6-TQFP44

Abstract: J1 HE10 HE10 TS271ACD
Contextual Info: STEVAL-IHM015V1 Low voltage motor control demonstration kit based on the ST7MC2S4 and STS8DNH3LL Data Brief Features • Voltage range from 5 V to 48 V ■ Current up to 25 A ■ 8 A, 30 V power MOSFET STS8DNH3LL dual device included ■ Compatible with power MOSFETs in SO-8 and

LM317T ST

Abstract: ST LM317t bc557 u210 u211 CON11 j6 con4 IN4148 schematic diagram lm317t R32A
Contextual Info: STEVAL-PCN001V1 USB power switch demonstration board Data Brief Features • Input parameters: – Load current: 100 mA, 500 mA, 1 A or 2 A. Larger loads can be applied by properly changing the load resistance R37 – Input voltage: 4.4 V, 4.75 V, 5.0 V or 5.25 V

Contextual Info: STEVAL-PCN001V1 USB power switch demonstration board Data Brief Features • ■ Input parameters: – Load current: 100 mA, 500 mA, 1 A or 2 A. Larger loads can be applied by properly changing the load resistance R37 – Input voltage: 4.4 V, 4.75 V, 5.0 V or 5.25 V

Contextual Info: L6219 Stepper motor driver Features • Able to drive both windings of bipolar stepper motor ■ Output current up to 750 mA each winding ■ Wide voltage range: 10 V to 46 V ■ Half-step, full-step and microstepping mode ■ Built-in protection diodes ■

GHS linker

Abstract: Tresos SPC563M 56xx RM0024 GHS multi wdgif_
Contextual Info: RM0024 Reference manual SPC563M AUTOSAR MCAL WDG driver integration Introduction This reference manual describes the integration requirements for the AUTOSAR microcontroller abstraction layer MCAL watchdog (WDG) driver for the SPC563M microcontrollers. The roadmap for the document is as follows:

tsm103w

Abstract: STEVAL-ILL017V1 s2h100 nonin VIPer17 ps2h100 BAT46 STTH1R06 ac bridg schematic diagram smps supply
Contextual Info: STEVAL-ILL017V1 Offline constant current LED driver based on the VIPer17 Data Brief Features • Input voltage 220 VAC +/- 20% ■ 800 V avalanche rugged power section ■ Provides 500 mA constant current for LED ■ High precision constant current with +/- 5%

d666

Abstract: CRX14 STM1404 st nand flash application note firmware cash register JTCK STEVAL-IPC001V1 STR710FZ2 A6 P113
Contextual Info: STEVAL-IPC001V1 Electronic fiscal cash register Data Brief Features • 4-Mbyte Flash, 32-Mbyte NAND and 1-Mbyte SRAM on board ■ Two smartcard readers ■ STM1404 secure chip, FIPS 140-2 compliant ■ Ethernet 10Base-T, 3 UARTs, 1 RS-485, 1 PS/ 2, 1 USB full speed, 4 x I2C, 1 x SPI, 2 LCDs

5973d

Abstract: W44X6 mlw10g S340U p45 connector STE101P LF18 LED1012 MLW-10 STR912FAW44
Contextual Info: STEVAL-IFW001V1 Real-time Ethernet slave node demonstration board based on the STR912FAW44 Data Brief Features • 32-bit STR912FAW44 microcontroller with ARM966E-S core running at 96 MHz ■ Two fast E-STE101P Ethernet transceivers supporting full duplex communication;

AN2475

Abstract: STR91xFAxxx ST Flash ldr 6k OX-400 STR91XFA
Contextual Info: AN2475 Application note STR91xFAxxx in-application programming using UART Introduction An important requirement for most Flash-based systems is the ability to update firmware while the system is installed in the end product. This is referred to as In-Application

STM8S

Abstract: stm8s207 PM0044 ST visual develop STVD user manual AN2752 STM8 CPU programming manual pm0044 STM8 Reference Manual adc example sTM8s STM8 programming manual PM0044 Programming manual
Contextual Info: AN2752 Application note Getting started with the STM8S Introduction This application note complements the information in the STM8S datasheets by describing the minimum hardware and software environment required to build an application around an STM8S 8-bit microcontroller device. It is divided into the following sections:

VT5376

Abstract: AN2732 CLK12 laser sensor I2C
Contextual Info: AN2732 Application note VT5376 laser calibration Introduction It is possible to automate the laser power calibration by using the VT5376 and an external MCU instead of the usual manual VCSEL binning method. This application note describes the method and equipment needed to perform this.

VT5363

Abstract: VT5363V032 800CPI
Contextual Info: STV-363-R04 VT5363 wired laser reference mouse Data Brief Features • Complete wired laser reference mouse ■ Single chip with minimal support circuitry ■ 800 cpi 400 cpi selectable ■ Accurate up to 40 ips ■ 9600 frames per second ■ Supports up to 5 buttons and scroll wheel

ST L6219 application note

Abstract: l6219 microstepping bipolar stepper motor circuit using L6219 power tube 67.5v E-L6219 E-L6219DS E-L6219DS013TR JESD97 L6219 PDIP24
Contextual Info: L6219 Stepper motor driver Features • Able to drive both windings of bipolar stepper motor ■ Output current up to 750 mA each winding ■ Wide voltage range: 10 V to 46 V ■ Half-step, full-step and microstepping mode ■ Built-in protection diodes ■

Contextual Info: STEVAL-IHM015V1 Low voltage motor control demonstration kit based on the ST7MC2S4 and STS8DNH3LL Data Brief Features • Voltage range from 5 V to 48 V ■ Current up to 25 A ■ 8 A, 30 V power MOSFET STS8DNH3LL dual device included ■ Compatible with power MOSFETs in SO-8 and

Contextual Info: STEVAL-IFW001V1 Real-time Ethernet slave node demonstration board based on the STR912FAW44 Data Brief Features • 32-bit STR912FAW44 microcontroller with ARM966E-S core running at 96 MHz ■ Two fast E-STE101P Ethernet transceivers supporting full duplex communication;