GP012A Search Results

servo motor AL 85

Abstract: 2953A
Contextual Info: FULL-BRIDGE PWM MOTOR DRIVERS UDN2953B NC VREF/B R A K E 0U To RC TIMING GROUND GROUND GROUND GROUND \c SENSE PHASE OUT, OUTPUT ENABLE The U D N 2953B and U D N 2954W are designed fo r bidirectional control of dc or stepper m otors with continuous output currents to 2 A

9736D

Abstract: UDN2879W UDN-2878W-2 UDN297
Contextual Info: 2 8 7 8 2 8 7 9 v \i> QUAD H IG H -CU RRENT D AR LIN G TO N SW ITCH ES These quad Darlington arrays are designed to serve as interface between low-level logic and peripheral power devices such as sole­ noids, motors, incandescent displays, heaters, and similar loads of up

Contextual Info: QUAD HIGH-CURRENT, HIGH-VOLTAGE SOURCE DRIVER Capable of driving loads to 4 A at supply voltages to 60 V Inductive loads to 35 V , the U D N 2944W is a quad high-current, highvoltage source driver. Each of the four power drivers can provide space- and cost-saving interface betw een low -level signal-processing

Contextual Info: — DUAL SOLENOID/MOTOR DRIVER PXJLSE-WIDTH MODULATED CURRENT CONTROL Using PWM to minimize power dissipation and maximize load efficiency, the UDN2962W dual driver is recommended for impact printer solenoids and stepper motors. It is comprised of two source/

GP012a

Contextual Info: QUAD HIGH-CURRENT DARLINGTON SWITCHES These quad Darlington a r r a y s are designed to serve as interface between low-level logic and peripheral power devices such as sole­ noids, motors, incandescent displays, heaters, and similar loads of up to 320 W per channel. Both integrated circuits include transientsuppression diodes that enable use with inductive loads. The input

8936 v 3

Abstract: j 5804 UDN2953B Wiring Diagram pwm motor controller 100J UDN2954W PWM H bridge servo motor controller 3 phase dynamic braking stepper-motor 5ph UDN-2954W
Contextual Info: 29319.2B a n d FULL-BBIDGE PWM MOTOR DRIVERS The UDN2953B and UDN2954W are designed for bidirectional control of dc or stepper motors with continuous output currents to 2 A and peak start-up currents as high as 3.5 A. For pulse-width modulated chopped-mode operation, the output current is determ ined by the

Contextual Info: ALLEGRO m C R O S Y S T E M S INC blE » 05 0 4 3 3 f l 2953 2954 a n 0003=14? 701 IAL6R d FZJLL-BRIDGE PWM MOTOR DRIVERS The UDN2953B and UDN2954W are designed for bidirectional control of dc or stepper motors with continuous output currents to 2 A and peak start-up currents as high as 3.5 A. For pulse-width modulated

2953A

Abstract: stepper motor stall current input output phase
Contextual Info: FULL-BRIDGE PWM MOTOR DRIVERS UDN2953B K NC OUTS V,&RAKE RC TIMING A GROUND GROUND GROUND GROUND SENSE (ACTIVE turned ON. When OUT, PHASE OUTPUT The UDN2953B and UDN2954W are designed for bidirectional control of dc or stepper motors with continuous output currents to 2 A

Contextual Info: QUAD HIGH-CURRENT DARLINGTON SWITCHES These quad Darlington arrays are designed to serve as interface between low-level logic and peripheral power devices such as sole­ noids, motors, incandescent displays, heaters, and similar loads of up to 320 W per channel. Both integrated circuits include transientsuppression diodes that enable use with inductive loads. The input

Contextual Info: 3-PHASE BRUSHLESS D C M OTOR CONTROLLER/DRTVERS Combining logic and power, the U D N 2936W and U D N 2936W -120 provide commutation and drive for three-phase brushless dc motors. Each of the three outputs are rated at 45 V and ±2 A ±3 A peak , and include internal ground clamp and flyback diodes. These drivers also

2953

Abstract: udn29538 UDN2953B UDN2954W UDN2954 A13024 RC servo motors GP-004-1 GP-012 GP012
Contextual Info: F U L L -B R ID G E F W M M O T O R D R IV E R S U D N 2953B 16 K 0UT# OUTPUT ENABLE {ACTIVE LOW I4 A 13 GROUND 12 GROUND II SENSE 10 ° uta VBB D w g. N o . A -1 3 .0 2 4 The UDN2953B and UDN2954W are designed fo r bidirectional control of d c or stepper m otors w ith continuous output currents to 2 A

UDN2954W

Abstract: DC SERVO MOTOR CONTROL circuit dynamic brake 100J UDN2953B rc servo motor back EMF pwm based bidirectional dc motor speed pwm based bidirectional dc motor speed control wiring circuit stepper motor UDN-2954W
Contextual Info: 29319.2B FVLL-BRIDGE PWM MOTOR DRIVERS UDN2953B NC ’ REF / b RAKE OUT„ RC TIMING GROUND GROUND GROUND GROUND SENSE PHASE OUTPUT ENABLE (ACTIVE LOW ) The UDN2953B and UDN2954W are designed for bidirectional control of dc or stepper motors with continuous output currents to 2 A

UDN2954W

Abstract: UDN2953B udn29538 speed and direction control of stepper motor servo motor control RC circuit UDN-2954W closed-loop stepper motor circuit rc servo control circuit 2954W Full-bridge forward converter
Contextual Info: 2953 2954 and FULL-BRIDGE PWM MOTOR DRIVERS UDN2S53B 16 K 15 OUT, 14 A 13 GROUND 12 GROUND II SENSE 10 outa OUTPUT ENABLE lA C T IV t LO W VBB Dwg. No. A -13,024 The UDN2953B and UDN2954W are designed for bidirectional control of dc or stepper motors with continuous output currents to 2 A

UDN2878W

Abstract: UDN2879W
Contextual Info: 2878 2879 QUAD HIGH-CURRENT DARLINGTON SWITCHES These quad Darlington arrays are designed to serve as interface between low-level logic and peripheral power devices such as sole­ noids, motors, incandescent displays, heaters, and similar loads of up to 320 W per channel. Both integrated circuits include transient-suppression diodes that enable use with inductive loads. The input logic is

Contextual Info: QUAD HIGH-C URRENT, HIGH-VOLTAGE SOURCE DRIVER GROUND I - Î:t 1 S{A,CV -REQ L I - o r C H g L ,N cls^ o u t c lr a — d ,. 1| ^ a n -o b i— IN n l» 1 - ENABLE i « J -O *- & VS f t 0>lQ- J ~ IN n la out. Is -J — o