CY7C964S Search Results
Documents mentioning CY7C964S
| Document | Partial File Text | Tags | Type | |||
|---|---|---|---|---|---|---|
| cy7c964 | W K fjT ' C Y 7C 964 Design Notes Introduction The CY7C964 is a flexible collection of byte (8-bit) wide transceivers, latches, counters, multiplexers, and comparators that provide bus interface designs with a low-cost alternative to PLDs, ASICs, or discrete logic |
OCR Scan | ||||
| cy7c960 | 3.10 Design Considerations 3.10.1 Design Philosophy The CY7C960 and the CY7C961 each share the basic VMEbus slave circuitry, and each has a common design philosophy. The most basic foundation for the design was that of achieving high performance in whatever system the devices were placed. For the CY7C960, that philosophy determined the hierarchical partitioning of the design into several independent blocks, |
Original | ||||
| vic068a | 1.10 VIC068A Block Transfer Functions The ability to transfer large blocks of data at a high-sustained transfer rate is paramount in today’s VMEbus market. When implemented properly, transfer rates exceeding 30 Mbyte/sec can be obtained using a high-speed processor, high-speed memory and highspeed VMEbus interfaces such as the VIC068A. |
Original | ||||
| cy7c960 | faxid 5709 Using the Slave VIC (CY7C960/961) Many VME boards, especially I/O boards, need only be aware of VME Slave transactions. Most commercially available VME interface chips are capable of both Master and Slave VME transactions and require some local intelligence, such as a |
Original | ||||
| cy7c964 | 3.6 CY7C964 Interface 3.6.1 CY7C964 Overview The CY7C960 is designed for use with the CY7C964 VMEbus Interface Logic Circuit. This device is fully described in Section 4, The CY7C964 Bus Interface Logic Circuit. The CY7C960 provides all the control and timing for the interface with the CY7C964. Interface timing as |
Original | ||||
| Frequently Asked Questions about the VMEbus | Frequently Asked Questions about the VMEbus Products The following questions are frequently asked by customers who are evaluating and using Cypress VMEbus Interface products. These answers will serve as an introduction for each topic. Separate application notes cover these topics in more complete detail. |
Original | ||||
| cy7c960 | 3.9 I/O Control Description The CY7C960 has two basic modes of operation: DRAM mode and I/O mode. The user selects the mode during configuration. This section describes the I/O mode of operation. In I/O mode the CY7C960 does not provide the timing signals required by DRAM, such as |
Original | ||||
| 3.5 VMEbus Interface Description 3.5.1 Definition | 3.5 VMEbus Interface Description 3.5.1 Definition of Terms DSi* Either or both of DS0* and DS1*, the VMEbus data strobe signals DSA* The first of DS0* or DS1* to be asserted DSB* The second of DS0* or DS1* to be asserted 6U, 3U The two most common sizes for VMEbus boards |
Original | ||||
| cy7c960 | faxid: 5709 Using the Slave VIC (CY7C960/961) Many VME boards, especially I/O boards, need only be aware of VME Slave transactions. Most commercially available VME interface chips are capable of both Master and Slave VME transactions and require some local intelligence, such as a |
Original | ||||
| cy7c960 | 3.9 I/O Control Description The CY7C960 has two basic modes of operation: DRAM mode and I/O mode. The user selects the mode during configuration. This section describes the I/O mode of operation. In I/O mode the CY7C960 does not provide the timing signals required by DRAM, such as |
Original | ||||
| vmebus | 3.5 VMEbus Interface Description 3.5.1 3.5.2 Definition of Terms DSi* Either or both of DS0* and DS1*, the VMEbus data strobe signals DSA* The first of DS0* or DS1* to be asserted DSB* The second of DS0* or DS1* to be asserted 6U, 3U The two most common sizes for VMEbus boards |
Original | ||||
| cy7c961 | 3.11 CY7C961 Description 3.11.1 Introduction The CY7C961 is a CY7C960 Slave VMEbus Interface Controller with the addition of a master block transfer capability. Full-featured Slave boards can be built, using the CY7C961, that offer a flexible Master block transfer facility for bursting data across the VMEbus. The CY7C961 |
Original | ||||
| cy7c960 | 3.4 Programming the CY7C960 The VMEbus board that is designed to use the CY7C960 has what might be called a personality. This encompasses such things as DRAM (speed and amount), I/O circuitry, SRAM, and other matters under the control of the board designer. To a large extent, this personality has |
Original | ||||
| 4.4 Signal Descriptions 4.4.1 VMEbus Signals | 4.4 Signal Descriptions 4.4.1 VMEbus Signals A[7:0] Input: Output: Drive: Yes Yes, three-state 48 mA These are VMEbus-compatible address signal transceivers that can be directly connected to the VMEbus. A0 is the least-significant address bit. In flow-through modes of operation, these |
Original | ||||
|
|
||||||
| vic068a | 4.3 Interfacing to Cypress VMEbus Interface Controllers Previously, interfacing the VIC068A to the VMEbus required a significant number of LSI and MSI devices. With the advent of 64Ćbit VMEbus block transfers and the VIC64, the exĆ ternal discrete device count for a full functional interface has expanded. The CY7C964 has |
Original | ||||
| cy7c960 | 3.10 Design Considerations 3.10.1 Design Philosophy The CY7C960 and the CY7C961 each share the basic VMEbus slave circuitry, and each has a common design philosophy. The most basic foundation for the design was that of achievĆ ing high performance in whatever system the devices were placed. For the CY7C960, that |
Original | ||||
| cy7c960 | Using the Slave VIC (CY7C960/961) Many VME boards, especially I/O Local Interrupts boards, need only be aware of VME Slave transactions. Most A64/A40 Support commercially available VME interface chips are caĆ pable of both Master and Slave VME transactions |
Original | ||||
| cy7c961 | 3.2 System Block Diagrams Four examples of system diagrams are shown: a 6U example, a 3U example, a low cost 6U implementation, and a CY7C961 3U example. Figure 3-4 shows an example of a 6U form factor board design. The details of the local circuitry are at the option of the board designer: this diagram illustrates the simplicity of the CY7C960 |
Original | ||||
| VIC64 to Motorola 68040 Interface Purpose This | VIC64 to Motorola 68040 Interface Purpose This application note shows how the VIC64 can be interfaced to a Motorola 68040 microprocessor operating at 40 MHz. The issues and assumptions that go into designing such an interface are considerable and complex; thus, this application |
Original | ||||
| cy7c964 | 4.1 Introduction The CY7C964 is a flexible collection of byte (8-bit) wide transceivers, latches, counters, multiplexers, and comparators that provide bus interface designs with a low-cost alternative to PLDs, ASICs, or discrete logic devices. It is based on a standard cell design that incorporates patented line drivers for reduced ground bounce and high noise immunity. The CY7C964 |
Original | ||||
| vme64 | 3.1 Introduction 3.1.1 Feature List Optimal Performance: Next-Generation Product: 80 Mbyte per second Block Transfer Rates VME64 transactions, including A64/D64, A40/MD32 transfers, Auto Slot ID, CR/CSR space, LOCK cycles etc. Backwards Compatible: All standard VMEbus transactions implemented |
Original | ||||
| cy7c960 | ‘ 3.3 PREN* SWDEN* RAS*/CS4 CAS*/CS5 AM2 ROW/CS2 COL/CS3 AM1 GND DBE0 AM0 Vcc DBE1 DBE2 DBE3 R/W* Pin Description Pin 1 CY7C960 TQFP Top View LA7 LA6 LA5 LA4 IRQ* LA3 Gnd AM5 LA2 Vcc LA1 DS1* LWORD* LDS DENIN1* LAEN DENO* IACKOUT* IACKIN* IACK* AS* LADI |
Original | ||||
| cy7c964 | fax id: 5706 Using the CY7C964 with VIC Using the CY7C964 with VIC The CY7C964 is a flexible collection of byte-wide (8-bit) transceivers, latches, counters, multiplexers, and comparators that provide VMEbus interface designs with a low-cost alternative to PLDS, ASICs, or discrete logic devices. It is based |
Original | ||||
| vic068a | 1.6 VIC068A VMEbus Slave Operations The act of writing or retrieving data for a VMEbus master is referred to as a slave operation. The VIC068A is able to perform slave operations with extensive configuration options. The following VIC068A registers are used in performing and configuring slave operations: |
Original | ||||