Part Number
    Please enter a valid full or partial manufacturer part number with a minimum of 3 letters or numbers

    CONFIGURING Search Results

    CONFIGURING Result Highlights (5)

    Part ECAD Model Manufacturer Description Download Buy
    10106131-2003501LF
    Amphenol Communications Solutions PwrBlade+®,Power Connectors,Vertical Recptacle 2P 12S configuration PDF
    10106135-4000501LF
    Amphenol Communications Solutions PwrBlade+®,Power Connectors, Right Angle Recptacle 4HDP configuration PDF
    10106267-0200K01LF
    Amphenol Communications Solutions PwrBlade+®,Power Connectors, Vertical Header 2LP configuration PDF
    10106267-0200403LF
    Amphenol Communications Solutions PwrBlade+®,Power Connectors, Vertical Header 2LP configuration PDF
    TUSB320LAIRWBR
    Texas Instruments Type-C Configuration Channel Logic and Port Control 12-X2QFN -40 to 85 Visit Texas Instruments Buy

    Documents mentioning CONFIGURING

    Document Partial File Text Tags Type PDF
    Configuring A Line Card This line card requires
    Configuring A Line Card This line card requires IPaction version 3.0 or later. To configure the line card see Configure Interfaces in the IPaction Software Configuration Guide on the documentation CD or the internet. Removing A Line Card 1. Loosen the screws located on both ends of the faceplate.
    Original PDF
    ac307
    Application Note AC307 Configuring SRAM FPGAs Using Actel Fusion™ Introduction Due to the nature of SRAM technology, SRAM-based FPGAs are volatile and lose their configuration when powered off, so they must be reconfigured at every power-up. Hence, almost every system using SRAMbased FPGAs contains an additional nonvolatile memory, such as flash PROM or EEPROM, to store the
    Original PDF
    ac284
    Application Note AC284 Configuring CorePWM Using RTL Blocks Introduction This application note describes the configuration of CorePWM using custom RTL blocks. A design example is provided to illustrate how a simple finite state machine (FSM) can be used to control the pulse-width
    Original PDF
    Configuration EPROMs / g ' T ï r f s W for FLEX
    Configuration EPROMs / g ' T ï r f s W for FLEX Devices y Data Sheet J a n u a r y 1 9 9 8 , v e r. 8 Features * ■ Serial EPROM family for configuring FLEX® devices Simple, easy-to-use 4-pin interface to FLEX devices Low current during configuration and near-zero standby current
    OCR Scan PDF
    Application Note: Configuring Networks for
    Application Note: Configuring Networks for Short-term Data Bursts Application Note: Configuring Networks for Short-term Data Bursts This document contains advance information of a product in development. All specifications are subject to change without notice. Consult LTC factory before using.
    Original PDF
    Wm H E W L E T T mL'EM P A C K A R D HP Em
    Wm H E W L E T T mL'EM P A C K A R D HP Em ulators and Developm ent Solutions for NEC V Series M icroprocessors Technical Data Design, debug, and integrate real-tim e embedded system s The HP 64700A card cage is the foundation in configuring a system to meet specific needs. A
    OCR Scan PDF
    Configuring Delta39K™/Quantum38K™ CPLDs Overview
    Configuring Delta39K™/Quantum38K™ CPLDs Overview This application note discusses the configuration interfaces, modes, and processes of the Delta39K™ and Quantum38K™ CPLDs and includes examples of device set-up. Each member of the Delta39K family is available in volatile
    Original PDF
    alpha power supply
    Alpha Customer Application Manual Section 2 - Paralleling Alpha Paralleling Options The Alpha power supply range can be fitted with parallel options which are designed to provide high current outputs (PP Option) or n + 1 redundancy. (PA Option) The type of option required is specified when configuring the Alpha unit.
    Original PDF
    xapp951
    ’ Application Note: Spartan-3E and Virtex-5 FPGAs R XAPP951 (v1.2) January 29, 2009 Summary Configuring Xilinx FPGAs with SPI Serial Flash Author: Stephanie Tapp This application note discusses the Serial Peripheral Interface (SPI) configuration mode introduced in the Virtex®-5 and Spartan®-3E FPGA families. The required connections to
    Original PDF
    xc95216
    XC95216 In-System Programmable CPLD  October 28, 1997 (Version 2.0) 3* Product Specification Features Power Management • Power dissipation can be reduced in the XC95216 by configuring macrocells to standard or low-power modes of operation. Unused macrocells are turned off to minimize
    Original PDF
    vlan
    Application Note 103 Micrel Application Note 103 Using a Tag-Based VLAN in a Gateway Solution KS8995M The LAN/WAN separation and WAN uplink overloading issues are resolved by configuring two different VLANs. VLAN 1 includes the LAN ports and the microprocessor port. VLAN
    Original PDF
    Features • Serial EEPROM Family for Configuring
    Features • Serial EEPROM Family for Configuring Altera FLEX 10K Devices • Simple, Easy-to-use 4-pin Interface • E2 Programmable 1M Bit Serial Memories Designed To Store Configuration Programs • For Programmable Gate Arrays
    Original PDF
    ha11218
    HA1 1 21 8 — P R E L IM IN A R Y — T V HORIZONTAL PROCESSOR AND VERTICAL OSCILLATOR AND DRIVER HA11218 can directly drive the vertical output transistors deflecting up to 20 inch color picture tube. For the output stage, only two NPN transistors configuring "totem-pole"
    OCR Scan PDF
    10. Configuring Cyclone III Devices CIII51010-1.1
    10. Configuring Cyclone III Devices CIII51010-1.1 Introduction Cyclone® III devices use SRAM cells to store configuration data. Because SRAM memory is volatile, configuration data must be downloaded to Cyclone III devices each time the device powers up. Depending on device densities or package options, Cyclone III devices can be configured using one
    Original PDF
    Section III. Advanced Configuration Schemes This
    Section III. Advanced Configuration Schemes This section discusses configuring configuration chains that contain a mixture of Altera® device families, combining different configuration schemes on your board and using a CPLD and flash memory to configure your Altera FPGA. It is recommended that you read the chapters in
    Original PDF
    11. Configuring Stratix III Devices SIII51011-1.1
    11. Configuring Stratix III Devices SIII51011-1.1 Introduction This chapter contains complete information on the Stratix® III supported configuration schemes, how to execute the required configuration schemes, and all the necessary option pin settings. Stratix III devices use SRAM cells to store configuration data. As SRAM
    Original PDF
    MIL Type Connector XG4M-U Easier Circuit Board
    MIL Type Connector XG4M-U Easier Circuit Board Wiring Connections • Can be connected and disconnected with one hand. • Improved lock lever operation. • Same locking strength as conventional models. • New cable flex-resistant lock mechanism. • Suitable for configuring compact, space-saving devices.
    Original PDF
    capsense
    Configuring CapSense Express in Production AN44203 Author: Pramodh Prakash Associated Project: No Associated Part Family: CY8C201xx GET FREE SAMPLES HERE Software Version: PSoC Express™ 3.0 Associated Application Notes: AN42137 Application Note Abstract
    Original PDF