TYCO CRIMP SPECIFICATION Search Results

Spec Crimping 114-16019

Abstract: CST-100
Contextual Info: Product Specification 108-1328 27Oct09 Rev A All Paragraphs Revised .100 Inch Centerline Crimp-Snap Connectors 1. SCOPE 1.1. Content This specification covers performance, tests and quality requirements for the Tyco Electronics .100 inch centerline Crimp-Snap connectors. The Crimp-Snap Terminal .100 product is a wire-to-board

CRIMP CONTACTS

Contextual Info: Product Specification 108-1579 27Apr07 Rev B Sealed Circular Plastic Connector With Removable Crimp Contacts 1. SCOPE 1.1. Content This specification covers performance, tests and quality requirements for Tyco Electronics sealed circular plastic connectors with removable crimp contacts. These connectors are designed for use in

BNC 1553

Abstract: Trompeter twin bnc twin bnc RG-108A twin bnc tyco TWC-124-2 MIL-P-19 Tool-69710-1 TWC-124 Trompeter Electronics
Contextual Info: RF Coax Connectors Twin BNC Connectors Product Facts • Crimp connectors require only one-stroke crimping of both conductors, plus braid and cable support ■ Lower installed cost with one-stroke crimp ■ Reduced noise levels because of Tyco Electronics

CST-100

Abstract: 2-641215-0 MTA-100 770601-1
Contextual Info: 501-341 Qualification Test Report 27Oct09 Rev A All Paragraphs Revised .100 Inch Centerline Crimp-Snap Connectors 1. INTRODUCTION 1.1. Purpose Testing was performed on the Tyco Electronics .100 Inch Centerline Crimp-Snap Connectors to determine their conformance to the requirements of Product Specification 108-1328 Revision A.

Contextual Info: 501-517 Qualification Test Report 27Apr07 Rev B Sealed Circular Plastic Connector With Removable Crimp Contacts 1. INTRODUCTION 1.1. Purpose Testing was performed on the Tyco Electronics sealed circular plastic connector with removable crimp contacts to determine its conformance to the requirements of Product Specification 108-1579 Revision

CST-100

Abstract: 1375819-1 1-640456-8
Contextual Info: Qualification Test Report 501-542 27Oct09 Rev A All Paragraphs Revised CST-100 Type II .100 Inch Centerline Crimp-Snap Connectors 1. INTRODUCTION 1.1. Purpose Testing was performed on the Tyco Electronics CST-100 Type II .100 Inch Centerline Crimp-Snap Connectors to determine their conformance to the requirements of Product Specification 108-1948

J1128 SXL

Abstract: SAE-J-1128 scd 301 SAE-J1128 detergent, "p-d-410" J1128 UL 486C UL 486C pull test SAE J1128 D5203
Contextual Info: Tyco Electronics Corporation 300 Constitutional Drive Menlo Park, CA 94025 USA No: Rev: Date: Page D-5203 1 February 19, 2002 1 of 12 D-5203 Specification, Pre-Insulated Crimp Splices 1 1.1 Introduction Scope This specification covers a series of one-piece pre-insulated crimp splices having a heatshrinkable polyolefin sleeve lined with a meltable adhesive coating.

CST-100

Abstract: EIA-364-20 EIA-364-21 EIA-364-27 EIA-364-28 EIA-364-8
Contextual Info: Product Specification 108-1948 27Oct09 Rev B All Paragraphs Revised CST-100 Type II .100 Inch Centerline Crimp-Snap Connectors 1. SCOPE 1.1. Content This specification covers performance, tests and quality requirements for Tyco Electronics CST-100 Type II .100 Inch Centerline Crimp-Snap Connectors. The CST-100 Type II product is a wire-to-board

Contextual Info: tlfCa — - Electronics 108-1579 P r0 d u c t . 19Dec01 RevA Specification e c 0990 - 1492-01 Sealed Circular Plastic Connector With Removable Crimp Contacts 1. SCOPE 1.1. Content This specification covers performance, tests and quality requirements fo r Tyco Electronics sealed

Contextual Info: FASTON Insulated and Uninsulated Terminals Catalog 1307612 Revised 7-01 FASTON Tabs Tyco Electronics offers a complete product line of printed circuit, crimp tabs and printed circuit board receptacles. Printed circuit board tabs are available in .110, .187,

crimp quality monitor

Abstract: 354500-1 354500-9 1490503-1 applicators 3545001
Contextual Info: AMP-O-LECTRIC Model G Terminating Machine Fast Facts • Quieter • Improved guarding and lighting • Toolless changeover of applicators • Precision manual- or autoadjust for crimp height • Total and batch counter • Accepts all existing Tyco Electronics miniature

DMC CRIMP

Abstract: 535B spec cable RG-174 DMC TOOL spec RG-174 cable tyco crimp specification
Contextual Info: 4 THIS DRAWING IS UNPUBLISHED. COPYRIGHT 2 3 RELEASED FOR PUBLICATION BY TYCO ELECTRONICS CORPORATION. — - LOC ALL RIGHTS RESERVED. REVIS IO N S DIST 6 AJ LTR DESCRIPTION 01 REVISED PER E C O - 0 5 - 0 0 7 7 0 4 DATE DWN APVD 02SEP05 BM KW D D CONTACT CRIMP TOOLING: CRIMP TOOL M 2 2 5 2 0 / 2 - 0 1 WITH POSTITIONER

Contextual Info: 4 THIS DRAWING IS UNPUBLISHED. COPYRIGHT 3 RELEASED FOR PUBLICATION BY TYCO ELECTRONICS CORPORATION. — 2 - LOC ALL RIGHTS RESERVED. R EVIS IO N S DIST 6 AJ LTR DESCRIPTION H1 DATE REVISED PER E C O - 0 5 - 0 0 7 7 0 4 DWN APVD BM KW 02SEP05 D D CONTACT CRIMP TOOLING: CRIMP TOOL M 2 2 5 2 0 / 2 - 0 1 WITH POSTITIONER DMC K997

AMP 59973-1

Abstract: 59973-1 AMP 59975-1 amp 69069 AMP 59974-1 DYNA-CRIMP 58422-1 1213875-1 69214-1 59974-1
Contextual Info: Continuing the quality and performance you’ve come to expect. Catalog 1654519 Revised 10-06 Hydraulic Crimp Tooling New 10,000 psi-rated Tools with Industry-standard U-Dies, Also Available with Portable, Powered Pumps Tyco Electronics continues the quality tradition of AMP crimping tools with a

UL858

Abstract: 408-9640 LR7189 41M-19 crimped terminal 3545001 UL-467
Contextual Info: Application Specification 114-13095 Grounding Clip Terminals with F" Crimp Feature NOTE i 18 JUN 09 Rev C All numerical values are in metric units [with U.S. customary units in brackets]. Dimensions are in millimeters [and inches]. Unless otherwise specified, dimensions have a tolerance of +0.13 [+.005] and angles have a tolerance of +2 .

Instruction Sheet 408-2095

Abstract: tyco crimp height specification Tyco 408-3295 354500-1 69710 hand drill bellmouth LR7189 maintenance manual 565435-5 408-7424
Contextual Info: Application Specification AMPINNERGY* Wire- to- Wire WTW Connectors NOTE i 114- 6051 11 DEC 09 Rev C All numerical values are in metric units [with U.S. customary units in brackets]. Dimensions are in millimeters [and inches]. Unless otherwise specified, dimensions have a tolerance of +0.13 [+.005] and angles have a tolerance of +2_.

checking terminal crimp height 408-7424

Abstract: Tyco 408-7424 bellmouth standard Tyco Electronics Instruction Sheet 408-7424 crimp 408-7424 checking terminal crimp height SPLICE TERMINAL tyco crimp height specification bellmouth 408-2823 instruction sheet 408-7424
Contextual Info: Application Specification 114-13196 Euro-Crimp Terminals and Splices NOTE i 01 MAY 07 Rev A All numerical values are in metric units [with U.S. customary units in brackets]. Dimensions are in millimeters. Unless otherwise specified, dimensions have a tolerance of +0.13 and angles have a tolerance of +2 . Figures and

tyco crimp height chart

Abstract: IPC-FC-220 IPC-FC-250 E53793 114-16008 illustrations of soldering metal sheets machine maintenance checklist 114-16008 terminal 108-16022 FC-220
Contextual Info: Application Specification Flexible Flat Cable FFC 114-16008 Connectors for 1.27 mm [.050 in.] Centerline Cable NOTE i 02 MAR 09 Rev K All numerical values are in metric units [with U.S. customary units in brackets]. Dimensions are in millimeters [and inches]. Unless otherwise specified, dimensions have a tolerance of +0.13 [+.005] and angles have a tolerance of +2 .

114-16015

Abstract: tyco crimp height chart IPC-FC-220 90273-5 E53793 tyco crimp height chart for 24 awg wire IPC-FC-250 e53793 connector certi-crimp bellmouth standard
Contextual Info: Application Specification Flexible Flat Cable FFC Housings with 114-16015 Contact Cavities on 2.54 mm [.100 in.] Centerline Spacing 10 DEC 07 Rev E All numerical values are in metric units [with U.S. customary units in brackets]. Dimensions are in millimeters [and

tag 8414

Abstract: TAG 8426 FAKRA Connector locking power jack raychem termination kit installation instructions M22520/05 Nexans RG 174 tyco crimp height specification Tyco crimp tool 1021 USCAR-18
Contextual Info: Application Specification 114- 13069 FAKRAh SMB 50- Ohm Inline Connectors NOTE i 01 MAR 10 Rev D All numerical values are in metric units [with U.S. customary units in brackets]. Dimensions are in millimeters [and inches]. Unless otherwise specified, dimensions have a tolerance of +0.13 [+.005] and angles have a tolerance of +2_.

Tyco 408-3295

Abstract: Tyco 408-7424 408-9816 blade receptacle two crimped terminal L012 354500-1 extraction tool tyco tyco crimp height specification
Contextual Info: Application Specification Wire- to- Board Connector for Hermaphroditic Blade and Receptacle SMT Connectors NOTE i 114- 13252 19 OCT 09 Rev D All numerical values are in metric units [with U.S. customary units in brackets]. Dimensions are in millimeters. Unless

91526-1

Abstract: 408-9640 466351-2 Tyco 408-3295 455822-2 455830-1 LR7189 tyco crimp height specification 354500-1 408-8059
Contextual Info: Application Specification 114- 1014 Miniature Rectangular MR Contacts and Housings 11 DEC 09 Rev D All numerical values are in metric units [with U.S. customary units in brackets]. Dimensions are in millimeters [and inches]. Unless otherwise specified, dimensions have a tolerance of +0.13 [+.005] and angles have a tolerance of +2_.

TAG 9031

Abstract: 408-8040 90272-1 AMP Crimp Snap Twin Leaf bellmouth tyco crimp height specification 408-9640 56770 crimped terminal 408-7424
Contextual Info: Application Specification 114- 9004 Twin Leaf Contacts NOTE i 18 SEP 09 Rev F All numerical values are in metric units [with U.S. customary units in brackets]. Dimensions are in millimeters [and inches]. Unless otherwise specified, dimensions have a tolerance of +0.13 [+.005] and angles have a tolerance of +2_.

tp1019

Abstract: 46756-2 69120-1 69099 16022 58095-1 69653 daniels* m310 M310 408-4374
Contextual Info: Application Specification 114- 16022 High Current Pin and Socket Contacts NOTE i 07 DEC 09 Rev B All numerical values are in metric units [with U.S. customary units in brackets]. Dimensions are in millimeters [and inches]. Unless otherwise specified, dimensions have a tolerance of +0.13 [+.005] and angles have a tolerance of +2_.