Part Number
    Please enter a valid full or partial manufacturer part number with a minimum of 3 letters or numbers

    STRAIN RESISTOR Search Results

    STRAIN RESISTOR Result Highlights (5)

    Part ECAD Model Manufacturer Description Download Buy
    65142-001LF
    Amphenol Communications Solutions Din Accessory Strain Relief Flat Cable PDF
    10073978-010LF
    Amphenol Communications Solutions Minitek® 2.00mm, Wire to Board Connector, Strain Relief for Receptacle. PDF
    10073978-040LF
    Amphenol Communications Solutions Minitek® 2.00mm, Wire to Board Connector, Strain Relief for Receptacle. PDF
    67016-026LF
    Amphenol Communications Solutions Quickie®, Wire To Board, Strain Relief, 26 Positions PDF
    67045-010LF
    Amphenol Communications Solutions Quickie®, Wire To Board, Strain Relief, 10 Positions PDF

    Documents mentioning STRAIN RESISTOR

    Document Partial File Text Tags Type PDF
    strain gauge
    Application Note 078 Strain Gauge Measurement – A Tutorial What is Strain? Strain is the amount of deformation of a body due to an applied force. More specifically, strain (ε) is defined as the fractional change in length, as shown in Figure 1 below. ε=
    Original PDF
    e18045
    Issued July 1994 E18045 Strain gauges and load cells Strain gauges Two ranges of foil strain gauges to cover general engineering requirements for strain analysis. All gauges have 30mm integral leads to alleviate damage to the gauges due to excessive heat being applied
    Original PDF
    Issued September 2001 232-5957 Data Pack E Data
    Issued September 2001 232-5957 Data Pack E Data Sheet Strain gauges and load cells Strain gauges Two ranges of foil strain gauges to cover general engineering requirements for strain analysis. All gauges have 30mm integral leads to alleviate damage to the gauges due to excessive heat being applied
    Original PDF
    Force and strain sensors. Measure. Test. Control.
    Force and strain sensors. Measure. Test. Control. Edition 2015 Force and strain sensors by Baumer combine tried and tested technology and sophisticated innovations. 1 Contents. Introduction 1 Display Boxes DDBF Product key  1.2 Summary Force and Strain Sensors1.4
    Original PDF
    PDFINFO H5 6 0 5 - 0 1 8-Channel 350 Ω Strain
    PDFINFO H5 6 0 5 - 0 1 8-Channel 350 Ω Strain Relay Multiplexer HP E1356A Technical Specifications ● 8-Channel 120 Ω strain gage relay multiplexer Strain gage measurements with bridge completion + 5 V excitation circuitry-quarter, half, and full
    Original PDF
    strain gage
    PDFINFO H2 3 8 6 - 0 1 120 Ω Strain Completion and Excitation SCP HP E1506A Technical Specifications ● Use with HP E1313A/E1413C/E1415A/E1419A 120 Ω strain completion and excitation Connections for quarter, half, and full bridge Requires an input SCP to make strain gage
    Original PDF
    e1507a
    PDFINFO H2 3 8 5 - 0 1 350 Ω Strain Completion and Excitation SCP HP E1507A Technical Specifications ● Use with HP E1313A/E1413C/E1415A/E1419A 350 Ω strain bridge completion and excitation Connections for quarter, half, and full bridge Requires an input SCP to make strain gage
    Original PDF
    Standard S-Type, Wire-Wound, and Hermetic
    Standard S-Type, Wire-Wound, and Hermetic Resistors Vishay Micro-Measurements Specifications and Selection Charts Fixed resistors have two primary uses in strain gage circuits: shunt calibration of strain-measuring instrumentation, and bridge completion. For shunt calibration, a fixed resistor is
    Original PDF
    an1011
    Application description AN1011: AM457 precision amplifier IC for strain gage elements This article describes a strain gag sensor circuit using the integrated circuit AM457 device to amplify and calibrate the output signal of a strain gage element with a Wheatstone resistance bridge. The aim is to obtain a ratiometric output signal Uout
    Original PDF
    Strain Gage Module for Compact FieldPoint NI
    Strain Gage Module for Compact FieldPoint NI cFP-SG-140 • Accepts full- and half-bridge strain gage inputs directly • Quarter-bridge gages require external bridge-completion resistor • Compatible with load cells, force sensors, and torque sensors • Built-in signal conditioning
    Original PDF
    Application Note 1818 Author: Don LaFontaine
    Application Note 1818 Author: Don LaFontaine Intersil and Freescale Thermocouple and Strain Gauge Reference Design Introduction Ordering Information The “Intersil and Freescale Thermocouple and Strain Gauge Reference Design” illustrates two sensor applications using
    Original PDF