Part Number
    Please enter a valid full or partial manufacturer part number with a minimum of 3 letters or numbers

    SPI 115 Search Results

    SPI 115 Result Highlights (5)

    Part ECAD Model Manufacturer Description Download Buy
    LM70CILDX-3/NOPB
    Texas Instruments ±2°C  Temperature Sensor with SPI Interface 8-WSON -55 to 150 Visit Texas Instruments Buy
    LM71CIMF
    Texas Instruments ±1.5°C Temperature Sensor with SPI Interface 5-SOT-23 Visit Texas Instruments
    TIPD138
    Texas Instruments SPI programmable 16-bit, 36V, 1A Power Supply with Integrated Current Shunt Visit Texas Instruments
    TMP125AIDBVR
    Texas Instruments Temperature Sensor with SPI Interface 6-SOT-23 -40 to 125 Visit Texas Instruments Buy
    TSC2005IYZLR
    Texas Instruments Nano-Power Touch Screen Controller with SPI Serial Interface 28-DSBGA -40 to 85 Visit Texas Instruments Buy

    Documents mentioning SPI 115

    Document Partial File Text Tags Type PDF
    SPI EXCHANGE SPI-3 TO SPI-4 Issue 1.0 FEATURES •
    SPI EXCHANGE SPI-3 TO SPI-4 Issue 1.0 FEATURES • Functionality - Low speed to high speed SPI exchange device - Logical port (LP) mapping (SPI-3 <-> SPI-4) tables per direction - Per LP configurable memory allocation - Maskable interrupts for fatal errors
    Original PDF
    SPI EXCHANGE 4 x SPI-3 TO SPI-4 Issue 1.0
    SPI EXCHANGE 4 x SPI-3 TO SPI-4 Issue 1.0 FEATURES • Functionality - Low speed to high speed SPI exchange device - Logical port (LP) mapping (SPI-3 <-> SPI-4) tables per direction - Per LP configurable memory allocation - Maskable interrupts for fatal errors
    Original PDF
    SPI EXCHANGE 2 x SPI-3 TO SPI-4 Issue 1.0
    SPI EXCHANGE 2 x SPI-3 TO SPI-4 Issue 1.0 FEATURES • Functionality - Low speed to high speed SPI exchange device - Logical port (LP) mapping (SPI-3 <-> SPI-4) tables per direction - Per LP configurable memory allocation - Maskable interrupts for fatal errors
    Original PDF
    avr151
    AVR151: Setup And Use of The SPI Features • SPI Pin Functionality Multi Slave Systems SPI Timing SPI Transmission Conflicts Emulating the SPI Code examples for Polled operation Code examples for Interrupt Controlled operation 8-bit RISC
    Original PDF
    88k8483
    IDT88K8483 SPI-4 Exchange Document Issue 1.0 Description Features Functionality – Multiplexes logical ports (LPs) from SPI-4A and SPI-4B to SPI4M – Optionally converts between interleaved packet transfers and whole packet transfers per logical port – Data redirection per LP between SPI-4A, SPI-4B and 10G
    Original PDF
    an10811
    AN10811 Programming SPI flash on EA3131 boards Rev. 01 — 1 May 2009 Application note Document information Info Content Keywords LPC3130, LPC3131, SPI flash Abstract Example for programming SPI flash on EA3131 boards. AN10811 NXP Semiconductors Programming SPI flash on EA3131 boards
    Original PDF
    LogiCORE IP AXI Serial Peripheral Interface (AXI
    LogiCORE IP AXI Serial Peripheral Interface (AXI SPI) (v1.02.a) DS742 January 18, 2012 Product Specification Introduction LogiCORE IP Facts The AXI Serial Peripheral Interface (SPI) connects to the Advanced eXtensible Interface (AXI4). This core provides a serial interface to SPI devices such as SPI
    Original PDF
    avr319
    AVR319: Using the USI module for SPI communication 8-bit Microcontrollers Features • C-code driver for SPI master and slave • Uses the USI module • Supports SPI Mode 0 and 1 Application Note Introduction The Serial Peripheral Interface (SPI) allows high-speed synchronous data transfer
    Original PDF
    avr303
    AVR303: SPI-UART Gateway Features • Communicate with a SPI slave device using a RS232 terminal SPI Modes 0–3, bit order and slave select (SS) is supported SPI clock frequency 28kHz to 1.8MHz when using a 3.6864MHz crystal Single byte transfer or multi-byte sequences
    Original PDF
    Active Errata List • During UART Reception,
    Active Errata List • During UART Reception, Clearing REN May Generate Unexpected IT Internal Resistor on Reset Pin SPI – SPI SS Pin Limitation on Master/Slave SPI – SPI Slave Responding in a Multislave Configuration When Not Selected by the
    Original PDF
    sc-1887
    SC-USB_SPI Datasheet Rev1; March 2010 SC-USB-SPI: USB to SPI Interface Adapter General Description_____ SC-USB-SPI is an adapter used for converting a computer’s USB interface connection to the Serial Parallel Interface (SPI) used by SC-1887. Only two connections are required for use with SC-1887 and no external
    Original PDF
    avr317
    AVR317: Using the Master SPI Mode of the USART module 8-bit Microcontrollers Features • Enables Two SPI buses in one device Hardware buffered SPI communication Polled communication example Interrupt-controlled communication example Application Note
    Original PDF
    at45db161e
    Atmel AT45DB161E 16-Mbit DataFlash (with Extra 512-Kbits), 2.3V or 2.5V Minimum SPI Serial Flash Memory PRELIMINARY DATASHEET Features  Single 2.3V - 3.6V or 2.5V - 3.6V supply  Serial Peripheral Interface (SPI) compatible Supports SPI modes 0 and 3
    Original PDF
    at45db161e
    Atmel AT45DB161E 16-Mbits DataFlash (with Extra 512-Kbits), 2.3V or 2.5V Minimum SPI Serial Flash Memory PRELIMINARY DATASHEET Features  Single 2.3V - 3.6V or 2.5V - 3.6V supply  Serial Peripheral Interface (SPI) compatible Supports SPI modes 0 and 3
    Original PDF
    lx5255
    LX5255 ® TM 9-Line LVD SCSI Terminator P RODUCTION DATA SHEET KEY FEATURES DESCRIPTION ƒ Compliant with SPI-2 (Ultra2), SPI-3 (Ultra160), and SPI-4 (Ultra320) ƒ 2.5pF Maximum Disabled Output Capacitance ƒ Fast Response, No External Capacitors Required
    Original PDF
    Errata • The SPI can Send Wrong Byte Reset During
    Errata • The SPI can Send Wrong Byte Reset During EEPROM Write SPI Interrupt Flag can be Undefined After Reset Serial Programming at Voltages below 3.0 Volts Skip Instruction with Interrupts 5. The SPI can Send Wrong Byte If the SPI is in master mode, it will restart the old transfer if new data is written on
    Original PDF
    Using the Serial Peripheral Interface (SPI) with
    Using the Serial Peripheral Interface (SPI) with AT91SAMxx Devices 1. Introduction This application note describes the use of the Serial Peripheral Interface (SPI) implemented in AT91SAMxx ARM® Thumb®-based devices. In this application note: • SPI main features are summarized,
    Original PDF