Part Number
    Please enter a valid full or partial manufacturer part number with a minimum of 3 letters or numbers

    LIGHT DEPENDING RESISTOR Search Results

    LIGHT DEPENDING RESISTOR Result Highlights (5)

    Part ECAD Model Manufacturer Description Download Buy
    RJMG3018241BAEH
    Amphenol Communications Solutions RJMG 1x1 10G, with led PDF
    RJMG3128711BANR
    Amphenol Communications Solutions RJMG 1x2 10G, with led PDF
    RJMG3226U11E3ER
    Amphenol Communications Solutions RJMG 2x6 10G, with led PDF
    RJMG301T221E3ER
    Amphenol Communications Solutions RJMG 1x1 10G, with led PDF
    UE86K112710621
    Amphenol Communications Solutions SFP 2X1 WITH LIGHT PIPE PDF

    Documents mentioning LIGHT DEPENDING RESISTOR

    Document Partial File Text Tags Type PDF
    L DESIGN FEATURES Monolithic Synchronous
    L DESIGN FEATURES Monolithic Synchronous Step-Down Regulator Sources 3A or Sinks 1.5A in TSSOP or 3mm × 4mm QFN by Genesia Bertelle Introduction Design Versatility Depending on the application requirements, a designer can either prioritize light load efficiency or minimize supply noise by choosing from three light
    Original PDF
    AND8135/D Efficient High Power Flash Light
    AND8135/D Efficient High Power Flash Light Prepared by: Michael Bairanzade ON Semiconductor http://onsemi.com APPLICATION NOTE INTRODUCTION Depending upon the type of flash involved, the amount of energy stored into capacitor C1 can be a low 10 Joule (small
    Original PDF
    elm337
    ELM337 Light Switch Description Features The ELM337 provides a convenient means to interface standard photocells or light dependent resistors (LDRs) to digital logic circuits. It provides an input comparator with hysteresis, line frequency filtering, digital delays, and high current output
    Original PDF
    SP4405 SIGNAL PROCESSING EXCELLENCE Low Voltage
    SP4405 SIGNAL PROCESSING EXCELLENCE Low Voltage Electroluminescent Lamp Driver with Regulated Output Voltage ■ +2.2V to +4.5V Battery Operation ■ DC-to-AC Converter Produces 160VPP typical for EL Display Panels ■ Single Resistor Controlled Internal Oscillator
    Original PDF
    sp4405
    ® SP4405 Low Voltage Electroluminescent Lamp Driver with Regulated Output Voltage ■ +2.2V to +4.5V Battery Operation ■ DC-to-AC Converter Produces 160VPP typical for EL Display Panels ■ Single Resistor Controlled Internal Oscillator ■ Low Current Standby Mode
    Original PDF
    81a3001b
    CHIP RESISTOR 5 WATT POWER RATING DATA SHEET PART NUMBER: 81A3001BXXXF FEATURES EN 13-0466 02/26/2013 SHEET 1 OF 1 APPLICATIONS Small Size – Light Weight Rugged Thin Film Moisture Resistant Surface Mount Broadcast High Power Filters High Power Amplifiers
    Original PDF
    PCR Printed Circuit Resistors FEATURES PIHER
    PCR Printed Circuit Resistors FEATURES PIHER Printed Circuit Resistors are thick-film elements designed to be printed on a wide range of non-conductive substrates. These range from ceramic to most PCB materials allowing the elimination of resistor, jumper wire, etc. insertion problems and
    Original PDF
    PCR Printed Circuit Resistors FEATURES PIHER
    PCR Printed Circuit Resistors FEATURES PIHER Printed Circuit Resistors are thick-film elements designed to be printed on a wide range of non-conductive substrates. These range from ceramic to most PCB materials allowing the elimination of resistor, jumper wire, etc. insertion problems and
    Original PDF
    Supertex inc. CL8801 Sequential Linear LED Driver
    Supertex inc. CL8801 Sequential Linear LED Driver Features ►►►►►►►►►►► General Description Minimal component count (base config: CL8801 + 4 resistors + diode bridge) No magnetics, no capacitors Up to 13W output
    Original PDF
    Supertex inc. CL8801 Sequential Linear LED Driver
    Supertex inc. CL8801 Sequential Linear LED Driver Features General Description ►► Minimal component count (base config: CL8801 + 4 resistors + diode bridge) ►► No magnetics, no capacitors ►► Up to 13W output ►► >115Lm/W using efficient LEDs
    Original PDF
    lx1972
    LX1972 ® TM Ambient Light Detector P RODUCTION S PECIFICATION KEY FEATURES DESCRIPTION Dynamic range is determined by the resistors (typically in the range of 10K to 100K) and power supply values. Typically the LX1972 needs only 1.8V of headroom to operate at 1000 Lux
    Original PDF
    lx1974
    LX1974 ® TM Ambient Light Detector P RODUCTION D ATA S HEET KEY FEATURES DESCRIPTION Dynamic range is determined by the resistors (typically in the range of 10K to 100K) and power supply values. Typically the LX1974 needs only 1.8V of headroom to operate at 1000 Lux
    Original PDF
    lx1972a
    LX1972A ® TM Ambient Light Detector P RODUCTION D ATA S HEET KEY FEATURES DESCRIPTION by placing it in series with a single resistor at either of its two pins. Dynamic range is determined by the resistors (typically in the range of 5K to 100K) and the power supply values.
    Original PDF
    lx1972
    LX1972 ® TM Ambient Light Detector P RODUCTION S PECIFICATION KEY FEATURES DESCRIPTION Dynamic range is determined by the resistors (typically in the range of 10K to 100K) and power supply values. Typically the LX1972 needs only 1.8V of headroom to operate at 1000 Lux
    Original PDF
    cl8800
    Supertex inc. CL8800 Sequential Linear LED Driver Features ►► Minimal component count (base config: CL8800 + 6 resistors + diode bridge) ►► No magnetics, no capacitors ►► Up to 13W output ►► >115Lm/W using efficient LEDs ►► 90% typical electrical efficiency
    Original PDF
    sfh551
    SIEMENS 6 Application Notes Digital Optical Receiver with Integrated Amplifier From the SFH551 to the SFH551/1 Introduction A simple design of the electronic circuitry is an essential step for the implementation of low cost optical links. In many cases optical emitters can be directly driven by logic gates through
    OCR Scan PDF
    PCR Printed Circuit Resistors FEATURES PIHER
    PCR Printed Circuit Resistors FEATURES PIHER Printed Circuit Resistors are thick-film elements designed to be printed on a wide range of non-conductive substrates. These range from ceramic to most PCB materials allowing the elimination of resistor, jumper wire, etc. insertion problems and
    Original PDF