L4981 EQUIVALENT Search Results
L4981 EQUIVALENT Result Highlights (5)
| Part | ECAD Model | Manufacturer | Description | Download | Buy |
|---|---|---|---|---|---|
| TMP89FM42UG | Toshiba Electronic Devices & Storage Corporation | 8-bit Microcontroller/Processing Performance Equivalent to a 16-bit MCU/LQFP44-P-1010-0.80B | Datasheet | ||
| TMP89FM42LUG | Toshiba Electronic Devices & Storage Corporation | 8-bit Microcontroller/Processing Performance Equivalent to a 16-bit MCU/LQFP44-P-1010-0.80B | Datasheet | ||
| TMP89FS28LFG | Toshiba Electronic Devices & Storage Corporation | 8-bit Microcontroller/Processing Performance Equivalent to a 16-bit MCU/LQFP176-P-2020-0.40D | Datasheet | ||
| TMP89FS62BUG | Toshiba Electronic Devices & Storage Corporation | 8-bit Microcontroller/Processing Performance Equivalent to a 16-bit MCU/P-LQFP44-1010-0.80-003 | Datasheet | ||
| TMP89FM42KUG | Toshiba Electronic Devices & Storage Corporation | 8-bit Microcontroller/Processing Performance Equivalent to a 16-bit MCU/LQFP44-P-1010-0.80B | Datasheet |
Documents mentioning L4981 EQUIVALENT
| Document | Partial File Text | Tags | Type | |||
|---|---|---|---|---|---|---|
| an628 | AN628 APPLICATION NOTE DESIGNING A HIGH POWER FACTOR SWITCHING PREREGULATOR WITH THE L4981 CONTINUOUS MODE by G. Comandatore and U. Moriconi INTRODUCTION Conventional AC-DC converters usually employ a full wave rectifier bridge with a simple capacitor |
Original | ||||
| an1606 | AN1606 APPLICATION NOTE A "BRIDGELESS P.F.C. CONFIGURATION" BASED ON L4981 P.F.C. CONTROLLER. by Ugo Moriconi This technical document describes an innovative topology dedicated to a medium to high power PFC stage. The originality of this topology is the absence of the bridge that usually is placed between the |
Original | ||||
| l4981 | APPLICATION NOTE DESIGNING A HIGH POWER FACTOR SWITCHING PREREGULATOR WITH THE L4981 CONTINUOUS MODE by G. Comandatore and U. Moriconi INTRODUCTION Conventional AC-DC converters usually employ a full wave rectifier bridge with a simple capacitor filter to draw power from the AC line. This ”bulk” |
Original | ||||
| l4981 | APPLICATION NOTE DESIGNING A HIGH POWER FACTOR SWITCHING PREREGULATOR WITH THE L4981 CONTINUOUS MODE by G. Comandatore and U. Moriconi INTRODUCTION Conventional AC-DC converters usually employ a full wave rectifier bridge with a simple capacitor filter to draw power from the AC line. This "bulk" |
Original | ||||
| an628 | ® AN628 APPLICATION NOTE DESIGNING A HIGH POWER FACTOR SWITCHING PREREGULATOR WITH THE L4981 CONTINUOUS MODE by G. Comandatore and U. Moriconi INTRODUCTION Conventional AC-DC converters usually employ a full wave rectifier bridge with a simple capacitor filter to draw power from the AC line. This "bulk" |
Original | ||||
| APPLICATION NOTE SEMICONDUCTOR KIT FOR POWER | APPLICATION NOTE SEMICONDUCTOR KIT FOR POWER FACTOR CORRECTOR by J. M. Borgeous This paper present a new line of P.F.C. dedicated products. Both silicon and packaging have been optimized to reduce system cost, including filtering. The products shown here are offered as a kit for |
Original | ||||
| APPLICATION NOTE SEMICONDUCTOR KIT FOR POWER | APPLICATION NOTE SEMICONDUCTOR KIT FOR POWER FACTOR CORRECTOR by J. M. Borgeous This paper present a new line of P.F.C. dedicated products. Both silicon and packaging have been optimized to reduce system cost, including filtering. The products shown here are offered as a kit for |
Original | ||||
| an829 | AN829 APPLICATION NOTE SEMICONDUCTOR KIT FOR POWER FACTOR CORRECTOR by J.M. Borgeous This paper present a new line of P.F.C. dedicated products. Both silicon and packaging have been optimized to reduce system cost, including filtering. The products shown here are offered as a kit for power |
Original | ||||
| APPLICATION NOTE SEMICONDUCTOR KIT FOR POWER | APPLICATION NOTE SEMICONDUCTOR KIT FOR POWER FACTOR CORRECTOR by J. M. Borgeous This paper present a new line of P.F.C. dedicated products. Both silicon and packaging have been optimized to reduce system cost, including filtering. The products shown here are offered as a kit for |
Original | ||||
| l4981a | APPLICATION NOTE A 500W HIGH POWER FACTOR WITH THE L4981A CONTINUOUS MODE IC The widespread use of passive AC/DC off-line converters causes low power factor and high line current harmonic distortion. To reduce these phenomena and to comply with relevant regulatory |
Original | ||||
| APPLICATION NOTE A 500W HIGH POWER FACTOR WITH | APPLICATION NOTE A 500W HIGH POWER FACTOR WITH THE L4981A CONTINUOUS MODE IC The widespread use of passive AC/DC off-line converters causes low power factor and high line current harmonic distortion. To reduce these phenomena and to comply with relevant regulatory |
Original | ||||
| an827 | AN827 APPLICATION NOTE A 500W HIGH POWER FACTOR WITH THE L4981A CONTINUOUS MODE IC The widespread use of passive AC/DC off-line converters causes low power factor and high line current harmonic distortion. To reduce these phenomena and to comply with relevant regulatory agency requirements , designers are employing active power factor correction in their off-line SMPS applications. This |
Original | ||||
| l4981a | APPLICATION NOTE A 500W HIGH POWER FACTOR WITH THE L4981A CONTINUOUS MODE IC The widespread use of passive AC/DC off-line converters causes low power factor and high line current harmonic distortion. To reduce these phenomena and to comply with relevant regulatory |
Original | ||||
| l4981a | L4981A L4981B POWER FACTOR CORRECTOR ADVANCE DATA CONTROL BOOST PWM UP TO 0.99P.F. LIMIT LINE CURRENT DISTORTION TO < 5% UNIVERSAL INPUT MAINS FEED FORWARD LINE AND LOAD REGULATION AVERAGE CURRENT MODE PWM FOR MINIMUM NOISE SENSITIVITY HIGH CURRENT BIPOLAR AND DMOS TOTEM POLE OUTPUT |
Original | ||||
|
|
||||||
| an2530 | AN2530 Application note Solution for 150 W half bridge resonant DC-DC converter Introduction This application note describes a 150 W Half bridge resonant DC-DC converter. This type of SMPS is highly attractive due to its high achievable efficiency, very low noise and compact |
Original | ||||
| an1616 | AN1616 APPLICATION NOTE THD-OPTIMIZER CIRCUITS FOR PFC PRE-REGULATORS by Claudio Adragna Although THD (Total Harmonic Distortion) is not explicitly considered in IEC 61000-3-2 standards, neither it needs to be very low in order for a piece of equipment to get the presumption of conformity, however it has become established to require an ultra-low THD in some applications such as electronic |
Original | ||||
| APPLICATION NOTE P.F.C. APPLICATION IDEAS USING | APPLICATION NOTE P.F.C. APPLICATION IDEAS USING MAINS TRANSFORMER The typical PFC boost scheme is mainly suggested for off-line applications, with the galvanic insulation located in the downstream converter side. There are some industrial and consumer applications in which the galvanic insulation is provided by |
Original | ||||
| APPLICATION NOTE P.F.C. APPLICATION IDEAS USING | APPLICATION NOTE P.F.C. APPLICATION IDEAS USING MAINS TRANSFORMER The typical PFC boost scheme is mainly suggested for off-line applications, with the galvanic insulation located in the downstream converter side. There are some industrial and consumer applications in which the galvanic insulation is provided by |
Original | ||||
| an825 | AN825 APPLICATION NOTE P.F.C. APPLICATION IDEAS USING MAINS TRANSFORMER The typical PFC boost scheme is mainly suggested for off-line applications, with the galvanic insulation located in the downstream converter side. There are some industrial and consumer applications in which the galvanic insulation is provided by |
Original | ||||
| APPLICATION NOTE P.F.C. APPLICATION IDEAS USING | APPLICATION NOTE P.F.C. APPLICATION IDEAS USING MAINS TRANSFORMER The typical PFC boost scheme is mainly suggested for off-line applications, with the galvanic insulation located in the downstream converter side. There are some industrial and consumer applications in which the galvanic insulation is provided by |
Original | ||||
| an825 | AN825 APPLICATION NOTE ® P.F.C. APPLICATION IDEAS USING MAINS TRANSFORMER The typical PFC boost scheme is mainly suggested for off-line applications, with the galvanic insulation located in the downstream converter side. There are some industrial and consumer applications in which the galvanic insulation is provided by |
Original | ||||
| an2649 | AN2649 Application note A power factor corrector with MDmeshTM II and SiC diode Introduction The electrical and thermal performances of switching converters are strongly influenced by the behavior of the switching devices. Modern power devices design requires a trade-off in |
Original | ||||
| an1485 | AN1485 APPLICATION NOTE MDmesh™ PERFORMANCE EVALUATION IN A CONTINUOUS MODE PFC BOOST CONVERTER G. Belverde - M. Melito - A. Raciti - M. Saggio - S. Musumeci 1. ABSTRACT A new high voltage MOSFET structure is presented which results in static as well as dynamic |
Original | ||||
| an2951 | AN2951 Application note 3 kW fixed-off-time (FOT) power factor correction Introduction In recent years, regulation in terms of electrical efficiency, electromagnetic noise, and reliability of the electronic apparatus, in all the application fields, are pushing to use power |
Original | ||||
| an3027 | AN3027 Application note How to design a transition-mode PFC pre-regulator with the L6563S and L6563H Introduction The transition-mode (TM) technique is widely used for power factor correction in low and middle power applications such as lamp ballasts, high-end adapters, flatscreen TVs and |
Original | ||||