Part Number
    Please enter a valid full or partial manufacturer part number with a minimum of 3 letters or numbers

    L4981 DATASHEET Search Results

    Documents mentioning L4981 DATASHEET

    Document Partial File Text Tags Type PDF
    l4981a
    APPLICATION NOTE A 500W HIGH POWER FACTOR WITH THE L4981A CONTINUOUS MODE IC The widespread use of passive AC/DC off-line converters causes low power factor and high line current harmonic distortion. To reduce these phenomena and to comply with relevant regulatory
    Original PDF
    APPLICATION NOTE A 500W HIGH POWER FACTOR WITH
    APPLICATION NOTE A 500W HIGH POWER FACTOR WITH THE L4981A CONTINUOUS MODE IC The widespread use of passive AC/DC off-line converters causes low power factor and high line current harmonic distortion. To reduce these phenomena and to comply with relevant regulatory
    Original PDF
    an827
    AN827 APPLICATION NOTE A 500W HIGH POWER FACTOR WITH THE L4981A CONTINUOUS MODE IC The widespread use of passive AC/DC off-line converters causes low power factor and high line current harmonic distortion. To reduce these phenomena and to comply with relevant regulatory agency requirements , designers are employing active power factor correction in their off-line SMPS applications. This
    Original PDF
    l4981a
    APPLICATION NOTE A 500W HIGH POWER FACTOR WITH THE L4981A CONTINUOUS MODE IC The widespread use of passive AC/DC off-line converters causes low power factor and high line current harmonic distortion. To reduce these phenomena and to comply with relevant regulatory
    Original PDF
    an2530
    AN2530 Application note Solution for 150 W half bridge resonant DC-DC converter Introduction This application note describes a 150 W Half bridge resonant DC-DC converter. This type of SMPS is highly attractive due to its high achievable efficiency, very low noise and compact
    Original PDF
    an1616
    AN1616 APPLICATION NOTE THD-OPTIMIZER CIRCUITS FOR PFC PRE-REGULATORS by Claudio Adragna Although THD (Total Harmonic Distortion) is not explicitly considered in IEC 61000-3-2 standards, neither it needs to be very low in order for a piece of equipment to get the presumption of conformity, however it has become established to require an ultra-low THD in some applications such as electronic
    Original PDF
    APPLICATION NOTE P.F.C. APPLICATION IDEAS USING
    APPLICATION NOTE P.F.C. APPLICATION IDEAS USING MAINS TRANSFORMER The typical PFC boost scheme is mainly suggested for off-line applications, with the galvanic insulation located in the downstream converter side. There are some industrial and consumer applications in which the galvanic insulation is provided by
    Original PDF
    APPLICATION NOTE P.F.C. APPLICATION IDEAS USING
    APPLICATION NOTE P.F.C. APPLICATION IDEAS USING MAINS TRANSFORMER The typical PFC boost scheme is mainly suggested for off-line applications, with the galvanic insulation located in the downstream converter side. There are some industrial and consumer applications in which the galvanic insulation is provided by
    Original PDF
    an825
    AN825 APPLICATION NOTE  P.F.C. APPLICATION IDEAS USING MAINS TRANSFORMER The typical PFC boost scheme is mainly suggested for off-line applications, with the galvanic insulation located in the downstream converter side. There are some industrial and consumer applications in which the galvanic insulation is provided by
    Original PDF
    APPLICATION NOTE P.F.C. APPLICATION IDEAS USING
    APPLICATION NOTE P.F.C. APPLICATION IDEAS USING MAINS TRANSFORMER The typical PFC boost scheme is mainly suggested for off-line applications, with the galvanic insulation located in the downstream converter side. There are some industrial and consumer applications in which the galvanic insulation is provided by
    Original PDF
    an825
    AN825 APPLICATION NOTE ® P.F.C. APPLICATION IDEAS USING MAINS TRANSFORMER The typical PFC boost scheme is mainly suggested for off-line applications, with the galvanic insulation located in the downstream converter side. There are some industrial and consumer applications in which the galvanic insulation is provided by
    Original PDF
    an2649
    AN2649 Application note A power factor corrector with MDmeshTM II and SiC diode Introduction The electrical and thermal performances of switching converters are strongly influenced by the behavior of the switching devices. Modern power devices design requires a trade-off in
    Original PDF
    an2951
    AN2951 Application note 3 kW fixed-off-time (FOT) power factor correction Introduction In recent years, regulation in terms of electrical efficiency, electromagnetic noise, and reliability of the electronic apparatus, in all the application fields, are pushing to use power
    Original PDF
    an3027
    AN3027 Application note How to design a transition-mode PFC pre-regulator with the L6563S and L6563H Introduction The transition-mode (TM) technique is widely used for power factor correction in low and middle power applications such as lamp ballasts, high-end adapters, flatscreen TVs and
    Original PDF
    an3027
    AN3027 Application note How to design a transition-mode PFC pre-regulator with the L6563S and L6563H Introduction The transition-mode (TM) technique is widely used for power factor correction in low and middle power applications such as lamp ballasts, high-end adapters, flatscreen TVs and
    Original PDF
    an3027
    AN3027 Application note How to design a transition-mode PFC pre-regulator with the L6563S and L6563H Introduction The transition-mode (TM) technique is widely used for power factor correction in low and middle power applications such as lamp ballasts, high-end adapters, flatscreen TVs and
    Original PDF