Part Number
    Please enter a valid full or partial manufacturer part number with a minimum of 3 letters or numbers

    INTERRUPT DRIV Search Results

    INTERRUPT DRIV Result Highlights (3)

    Part ECAD Model Manufacturer Description Download Buy
    CS-SATDRIVEX2-002
    Amphenol Cables on Demand Amphenol CS-SATDRIVEX2-002 Serial ATA Extension Cable - SATA II Drive Extension Cable with Power (6.0 Gbps) 2m PDF
    CS-SATDRIVEX2-000.5
    Amphenol Cables on Demand Amphenol CS-SATDRIVEX2-000.5 Serial ATA Extension Cable - SATA II Drive Extension Cable with Power (6.0 Gbps) 0.5m PDF
    CS-SATDRIVEX2-001
    Amphenol Cables on Demand Amphenol CS-SATDRIVEX2-001 Serial ATA Extension Cable - SATA II Drive Extension Cable with Power (6.0 Gbps) 1m PDF

    Documents mentioning INTERRUPT DRIV

    Document Partial File Text Tags Type PDF
    in te i PRELIMINARY 82093AA I/O ADVANCED
    in te i PRELIMINARY 82093AA I/O ADVANCED PROGRAMMABLE INTERRUPT CONTROLLER (IOAPIC) ■ Provides Multiprocessor Interrupt Management — Dynamic Interrupt DistributionRouting Interrupt to the Lowest Priority Processor — Software Programmable Control of Interrupt Inputs
    OCR Scan PDF
    in te i PRELIMINARY 82093AA I/O ADVANCED
    in te i PRELIMINARY 82093AA I/O ADVANCED PROGRAMMABLE INTERRUPT CONTROLLER (IOAPIC) ■ Provides Multiprocessor Interrupt Management — Dynamic Interrupt DistributionRouting Interrupt to the Lowest Priority Processor — Software Programmable Control of Interrupt Inputs
    OCR Scan PDF
    st10f168
     ST10X167/ST10F168 Programming ST10X167/ST10F168 CAN interrupt drivers APPLICATION NOTE This application note describes the CAN interrupt drivers of the ST10X167/ST10F168 and provides programming examples that can be used to define interrupt schemes and write interrupt drivers.
    Original PDF
    an2628
    AN2628 Application note Programming ST10F27x CAN interrupt drivers Introduction This application note describes the CAN interrupt drivers of the ST10F27x and provides programming examples that can be used to define interrupt schemes and write interrupt drivers. Two C-CAN modules are implemented on ST10F27x, mapped on XBUS.
    Original PDF
    82093aa
    E PRELIMINARY 82093AA I/O ADVANCED PROGRAMMABLE INTERRUPT CONTROLLER (IOAPIC)  3 General Purpose Interrupts  Independently Programmable for Provides Multiprocessor Interrupt Management  Dynamic Interrupt DistributionRouting Interrupt to the Lowest
    Original PDF
    p8xc592
    Philips Semiconductors Product specification 8-bit microcontroller with on-chip CAN CONTENTS P8xC592 14 INTERRUPT SYSTEM Interrupt Enable and Priority Registers Interrupt Vectors Interrupt Priority 1 FEATURES 2 GENERAL DESCRIPTION 14.1 14.2 14.3 3 ORDERING INFORMATION
    OCR Scan PDF
    an2341
    AN2341 Application note Programming ST10F27x/F25x CAN interrupt drivers Introduction This application note describes the CAN interrupt drivers of the ST10F27x/ST10F25x and provides programming examples that can be used to define interrupt schemes and write
    Original PDF
    INTEGRATED CIRCUITS Functional description of
    INTEGRATED CIRCUITS Functional description of Philips arbitrating interrupt systems author: Peter Narvaez Philips Semiconductors Philips Semiconductors Article reprint Functional description of Philips arbitrating interrupt systems Author: Peter Narvaez CIR value is used to drive the interrupt vector modification (when
    Original PDF
    pd71059
    SEC ¿/PD71059 Interrupt Control Unit Pin C onfigurations Description The //PD71059 is a low-power CMOS programmable interrupt control unit for microcomputer systems. It can process eight interrupt request inputs, allocating a priority level to each one. It transfers the interrupt with
    OCR Scan PDF
    80c51
    Philips Semiconductors 80C51 Family 80C51 family architecture The interrupt service locations are spaced at 8-byte intervals: 0003H for External Interrupt 0, 000BH for Timer 0, 0013H for External Interrupt 1, 001BH for Timer 1, etc. If an interrupt service routine is
    Original PDF
    pd71059
    NEC A/PD71059 Interrupt Control Unit NEC Electronics Inc. Description Pin Configurations The/uPD71059 is a low-power CMOS programmable interrupt control unit for microcomputer systems. It can process eight interrupt request inputs, allocating a priority level to each one. It transfers the interrupt with
    OCR Scan PDF
    gpib-1014p
    Programmed I/O GPIB Interfaces for VMEbus GPIB-1014P, GPIB-1014DP Features Complete IEEE 488 Talker/Listener/Controller Polled or interrupt driven transfers Transfer rates up to 80 kbytes/s User-configurable parameters Base address Interrupt request line Interrupt status/ID byte
    Original PDF
    avr304
    AVR304: Half Duplex Interrupt Driven Software UART Features • Runs asynchronously (interrupt driven) • Capable of handling baud rates of up to 38.4 kbaud @8MHz clock frequency • Runs on any AVR device with 8-bit timer/counter and external interrupt 8-bit
    Original PDF
    DASP-52096 High-density 96-channel DI/O Card 96
    DASP-52096 High-density 96-channel DI/O Card 96 TTL digital I/O channels Buffered circuits for higher driving capacity Multiple-source interrupt handling Interrupt output pin for simultaneously triggering external devices with the interrupt Output status read-back
    Original PDF
    80c51
    Philips Semiconductors 80C51 Family 80C51 family architecture The interrupt service locations are spaced at 8-byte intervals: 0003H for External Interrupt 0, 000BH for Timer 0, 0013H for External Interrupt 1, 001BH for Timer 1, etc. If an interrupt service routine is
    Original PDF
    pb8214
    /1PB8214 NEC NEC Electronics U SA Inc. Microcomputer Division PRIORITY INTERRUPT CONTRO LLER D ESC R IP T IO N The (JPB8214 is an eight-level priority interrupt controller. Designed to sim plify interrupt driven microcomputer systems, the /JPB8214 requires a single + 5 V power
    OCR Scan PDF
    71059
    CXQ71059 SONY Interrupt C o n tro l U nit Pin Configuration (Top View) Description The CXQ71059 is a low-powerCMOS programmable interrupt control unit for m icrocomputer system s. It can process eight interrupt requests and can be expanded to 6 4 interrupt requests by adding other
    OCR Scan PDF
    lz87010
    LZ87010 Advance Data Sheet FEATURES 8-bit Microcontroller • 8-bit, 40 MHz, 8051-compatible CPU core: – Two-clock Machine Cycle – Equivalent to a 240 MHz 8051 • Interrupt Controller – 8 External Interrupt Pins – 13 Internal Interrupt Sources – 4 Software-Selectable Interrupt Priorities
    Original PDF
    11 Host Interrupts The ZiVA decoder allows for
    11 Host Interrupts The ZiVA decoder allows for interrupt-driven host processing. The host can interrupt the decoder to force it to service a new command more quickly. Conversely, the decoder can interrupt the host, as described in this chapter, to send status information to the host.
    Original PDF