Part Number
    Please enter a valid full or partial manufacturer part number with a minimum of 3 letters or numbers

    INPUT RESI Search Results

    INPUT RESI Result Highlights (5)

    Part ECAD Model Manufacturer Description Download Buy
    DCL541A01
    Toshiba Electronic Devices & Storage Corporation Digital Isolator / VDD=2.25~5.5V / 150Mbps / 4 channel(F:R=3:1) / Default Output Logic: Low / Input disable Datasheet
    DCL541B01
    Toshiba Electronic Devices & Storage Corporation Digital Isolator / VDD=2.25~5.5V / 150Mbps / 4 channel(F:R=3:1) / Default Output Logic: High / Input disable Datasheet
    DCM341B01
    Toshiba Electronic Devices & Storage Corporation Digital Isolator / VDD=3.0~5.5V / 50Mbps / 4 channel(F:R=3:1) / Default Output Logic: High / Input disable / AEC-Q100 Datasheet
    DCM341A01
    Toshiba Electronic Devices & Storage Corporation Digital Isolator / VDD=3.0~5.5V / 50Mbps / 4 channel(F:R=3:1) / Default Output Logic: Low / Input disable / AEC-Q100 Datasheet
    TLP385
    Toshiba Electronic Devices & Storage Corporation Photocoupler (phototransistor output), DC input, 5000 Vrms, 4pin SO6L Datasheet

    Documents mentioning INPUT RESI

    Document Partial File Text Tags Type PDF
    NORMAL CHARACTERISTICS STATOR AS PRIMARY £6 VOLTS
    NORMAL CHARACTERISTICS STATOR AS PRIMARY £6 VOLTS INPUT VOLTS 400 Hz. INPUT CURRENT INPUT POWER IMPEDANCE, ZSO IMPEDANCE, ZSRS . D.C. RESISTANCE OUTPUT (ROTOR) PHASE SH IFT ACCURACY ROTOR AS PRIMARY INPUT VOLTS INPUT CURRENT INPUT POWER IMPEDANCE, ZRO IMPEDANCE.ZRSS
    OCR Scan PDF
    ua702c
    FAIRCHILD LINEAR INTEGRATED CIRCUITS • juA702 /UA702C ELECTRICAL CHARACTERISTICS (TA = 25°C unless otherwise specified) PARAMETER CONDITIONS Input Offset Voltage Input Offset Current Input Bias Current Input Resistance Input Voltage Range Common Mode Rejection Ratio
    OCR Scan PDF
    ad892e
    AD892E/AD892T COMPARATORS Input Offset Voltage Input Offset Current Input Bias Current Open Loop Gain Input Resistance Input Capacitance Input Common Mode Range O U TPU T /FIL TER O NE-SHOT Resistor Scaling5 Pulse Duration Resistor Range O U TPU T /FIL T ER O NE-SHOT
    OCR Scan PDF
    ad892e
    AD892E/AD892T COMPARATORS Input Offset Voltage Input Offset Current Input Bias Current Open Loop Gain Input Resistance Input Capacitance Input Common Mode Range O U TPU T /FIL TER O NE-SHOT Resistor Scaling5 Pulse Duration Resistor Range O U TPU T /FIL T ER O NE-SHOT
    OCR Scan PDF
    m3500-0916
    INPUT LIMITING INPUT VOLTAGE LIMITING (ON M3500-0916 ONLY) The M3500-0916 uses an input zener diode to clamp the input voltage at 13V. This guarantees that the VCO always has an output at high tune voltages. Micronetics recommends that an input resistor be used in designs where the input
    Original PDF
    nju3502
    NJU3502 „# TERMINAL DESCRIPTION 1 No. 22 23 1 2 SYMBOL PC0 PC1 PC2 PC3 INPUT/OUTPUT F U N C T I O N 4-bit Input / Output PORTC. INPUT/OUTPUT Selects a terminal circuit for each port from follows by the INPUT/OUTPUT mask option. INPUT/OUTPUT xC-MOS Input Terminal with Pull-up Resistance(IA)
    Original PDF
    pr500-280
    Series PR The PR module is an AC/DC rectifier compatible with all PH Series DC/DC models having an input voltage of 280VDC. PR500-280 INPUT Input voltage 85-132VAC 170-265VAC Input frequency 47 to 440Hz Input current 8.8A Inrush current Limited by external resistor
    Original PDF
    njmop-07
    NJMOP-07 Electrical Characteristics (Ta=+25°c, v +/v ~ = ± 15V) Param eter Input Offset Voltage Long Term Stability Input Offset Current Input Bias Current Open Loop O utput Resistance Input Resistance Input Resistance In p u t C o m m o n M ode V oltage Range
    OCR Scan PDF
    SCM7B36 Isolated Potentiometer Input Modules
    SCM7B36 Isolated Potentiometer Input Modules FEATURES DESCRIPTION ● INDUSTRY’S FIRST 7B POTENTIOMETER INPUT MODULE Each SCM7B36 Potentiometer input module provides a single channel of resistance input which is filtered, isolated, amplified, and converted to a high
    Original PDF
    njm2508
    NJM2508 ■APPLICATION This IC requires 1MΩ resistance between INPUT and GND pin for clamp type input since the minute current causes an unstable pin voltage. Input + - C ≅ 10uF r r ≅ 1MΩ This IC requires 0.1uF capacitor between INPUT and GND, 1MΩ resistance between INPUT and GND for
    Original PDF
    njm2248
    NJM2248 ■APPLICATION This IC requires 1MΩ resistance between INPUT and GND pin for clamp type input since the minute current causes an unstable pin voltage. + Input C ≅ 10uF r r ≅ 1MΩ This IC requires 0.1uF capacitor between INPUT and GND, 1MΩ resistance between INPUT and GND for
    Original PDF
    njm2506
    NJM2506 ■APPLICATION This IC requires 1MΩ resistance between INPUT and GND pin for clamp type input since the minute current causes an unstable pin voltage. Input + - C ≅ 10uF r r ≅ 1MΩ This IC requires 0.1uF capacitor between INPUT and GND, 1MΩ resistance between INPUT and GND for
    Original PDF
    njm2235
    220uF NJM2235 ■APPLICATION This IC requires 1MΩ resistance between INPUT and GND pin for clamp type input since the minute current causes an unstable pin voltage. + Input C ≅ 10uF r r ≅ 1MΩ This IC requires 0.1uF capacitor between INPUT and GND, 1MΩ resistance between INPUT and GND for
    Original PDF
    njm2266
    NJM2266 ■APPLICATION This IC requires 1MΩ resistance between INPUT and GND pin for clamp type input since the minute current causes an unstable pin voltage. + Input C ≅ 10uF r r ≅ 1MΩ This IC requires 0.1uF capacitor between INPUT and GND, 1MΩ resistance between INPUT and GND for
    Original PDF
    njm2249
    NJM2249 ■APPLICATION This IC requires 1MΩ resistance between INPUT and GND pin for clamp type input since the minute current causes an unstable pin voltage. + Input C ≅ 10uF r r ≅ 1MΩ This IC requires 0.1uF capacitor between INPUT and GND, 1MΩ resistance between INPUT and GND for
    Original PDF
    njm2535
    NJM2535 ■APPLICATION This IC requires 1MΩ resistance between INPUT and GND pin for clamp type input since the minute current causes an unstable pin voltage. + Input C ≅ 10uF r r ≅ 1MΩ This IC requires 0.1uF capacitor between INPUT and GND, 1MΩ resistance between INPUT and GND for
    Original PDF
    njm2535
    220uF NJM2535 ■APPLICATION This IC requires 1MΩ resistance between INPUT and GND pin for clamp type input since the minute current causes an unstable pin voltage. + Input C ≅ 10uF r r ≅ 1MΩ This IC requires 0.1uF capacitor between INPUT and GND, 1MΩ resistance between INPUT and GND for
    Original PDF
    njm2284
    NJM2284 ■APPLICATION This IC requires 1MΩ resistance between INPUT and GND pin for clamp type input since the minute current causes an unstable pin voltage. Input + - C ≅ 10uF r r ≅ 1MΩ This IC requires 0.1uF capacitor between INPUT and GND, 1MΩ resistance between INPUT and GND for
    Original PDF
    njm2263
    NJM2263 ■APPLICATION This IC requires 1MΩ resistance between INPUT and GND pin for clamp type input since the minute current causes an unstable pin voltage. + Input C ≅ 10uF r r ≅ 1MΩ This IC requires 0.1uF capacitor between INPUT and GND, 1MΩ resistance between INPUT and GND for
    Original PDF
    njm2285
    NJM2285 ■APPLICATION This IC requires 1MΩ resistance between INPUT and GND pin for clamp type input since the minute current causes an unstable pin voltage. Input + - C ≅ 10uF r r ≅ 1MΩ This IC requires 0.1uF capacitor between INPUT and GND, 1MΩ resistance between INPUT and GND for
    Original PDF
    njm2503
    NJM2503 ■APPLICATION This IC requires 1MΩ resistance between INPUT and GND pin for clamp type input since the minute current causes an unstable pin voltage. Input + - C ≅ 10uF r r ≅ 1MΩ This IC requires 0.1uF capacitor between INPUT and GND, 1MΩ resistance between INPUT and GND for
    Original PDF
    njm2244
    NJM2244 ■APPLICATION This IC requires 1MΩ resistance between INPUT and GND pin for clamp type input since the minute current causes an unstable pin voltage. + Input C ≅ 10uF r r ≅ 1MΩ This IC requires 0.1uF capacitor between INPUT and GND, 1MΩ resistance between INPUT and GND for
    Original PDF
    njm2535
    220uF NJM2535 ■APPLICATION This IC requires 1MΩ resistance between INPUT and GND pin for clamp type input since the minute current causes an unstable pin voltage. + Input C ≅ 10uF r r ≅ 1MΩ This IC requires 0.1uF capacitor between INPUT and GND, 1MΩ resistance between INPUT and GND for
    Original PDF
    njm2523
    NJM2523 ■APPLICATION This IC requires 1MΩ resistance between INPUT and GND pin for clamp type input since the minute current causes an unstable pin voltage. Input + - C ≅ 10uF r r ≅ 1MΩ This IC requires 0.1uF capacitor between INPUT and GND, 1MΩ resistance between INPUT and GND for
    Original PDF