Part Number
    Please enter a valid full or partial manufacturer part number with a minimum of 3 letters or numbers

    EPC30 BOBBIN Search Results

    Documents mentioning EPC30 BOBBIN

    Document Partial File Text Tags Type PDF
    epc13
    Ferrite Cores EPC Series For Power Supply and Signal Transformer EPC Cores C2 C CORE SHAPES AND DIMENSIONS/CHARACTERISTICS C1 A D U.S.PAT.4,760,366 EP.PAT.245,083(DE,FR,GB,NL) KS.UM50,836 TW.UM39,406 JP.PENDING C1 C2 C Fig.1 D A Type Fig. EPC10 EPC13 EPC17
    Original PDF
    epc-13
    EPC-13_TDK.pdf Ferrite Cores EPC Series For Power Supply and Signal Transformer EPC Cores C2 C CORE SHAPES AND DIMENSIONS/CHARACTERISTICS C1 A D U.S.PAT.4,760,366 EP.PAT.245,083(DE,FR,GB,NL) KS.UM50,836 TW.UM39,406 JP.PENDING C1 C2 C Fig.1 D A Type Fig. EPC10
    Original PDF
    (1/4) 001-01 / 20011019 / e151.fm Ferrite Cores
    (1/4) 001-01 / 20011019 / e151.fm Ferrite Cores EPC, ER, EEM, EE Series Low Loss Materials for Power Supply Materials PC45, PC46 Demand is greatly increasing for portable devices such as notebook PCs, camcorders, digital cameras, PDAs, GPS car navigation systems, etc. There is also growing demand for small, light
    Original PDF
    88em8080
    AppNote 88EM8080/88EM8081 Based Flyback PFC LED Power Supply Design 1. Introduction The flyback (isolated buck/boost) topology is used to simplify the two stage structure to a single isolated Power factor correction (PFC) conversion stage. The key to simplifying the two stage PFC
    Original PDF
    www.fairchildsemi.com Application Note AN4140 Transformer Design Consideration for off-line Flyback Converters using Fairchild Power Switch (FPSTM) 1. Introduction For flyback coverters, the transformer is the most important factor that determines the performance such as the
    Original PDF
    flyback transformer design
    APPLICATION NOTE AN-1024a International Rectifier • 233 Kansas Street El Segundo CA 90245 USA Flyback Transformer Design For The IRIS40xx Series By Jonathan Adams TOPICS COVERED Introduction To Flyback Transformer Design Power Supply Design Criteria Required
    Original PDF
    an-32
    ® TOPSwitch-GX Flyback Design Methodology Application Note AN-32 Designing an off-line power supply involves many aspects of electrical engineering: analog and digital circuits, bipolar and MOS power device characteristics, magnetics, thermal considerations, safety requirements, control loop stability, etc.
    Original PDF
    flyback transformer design
    Application Note AN-1024 Flyback Transformer Design for the IRIS40xx Series Table of Contents Page 1. Introduction to Flyback Transformer Design… 1 2. Power Supply Design Criteria Required… 2
    Original PDF
    an-4150
    www.fairchildsemi.com Application Note AN-4150 Design Guidelines for Flyback Converters Using FSQ-series Fairchild Power Switch (FPS™) 1. Introduction size and weight, while simultaneously increasing efficiency, productivity, and system reliability. The FSQ-series employs
    Original PDF
    flyback transformer construction
    ® TOPSwitch Flyback Transformer Construction Guide ® Application Note AN-18 Introduction Ferrite Core Manufacturer’s Catalogs This application note is a design and construction guide for margin wound or triple insulated wire wound flyback transformers suitable for use with TOPSwitch. Margin wound
    Original PDF
    topswitch-hx
    Application Note AN-43 TOPSwitch-HX Family ® Design Guide Introduction up and shutdown of the power supply during line sag or line surge conditions. Power Integrations’ EcoSmart® technology enables supplies designed around the TOPSwitch-HX family to consume less than 200 mW at no load and maintain constant
    Original PDF
    an-47
    Application Note AN-47 TOPSwitch-JX Family ® Design Guide Introduction The TOPSwitch-JX is a highly integrated monolithic off-line switcher IC designed for off-line power supplies. TOPSwitch-JX integrated circuits enable design of power supplies up to 244 W,
    Original PDF