Part Number
    Please enter a valid full or partial manufacturer part number with a minimum of 3 letters or numbers

    AMMETER DESIGN Search Results

    AMMETER DESIGN Result Highlights (5)

    Part ECAD Model Manufacturer Description Download Buy
    TIPD144
    Texas Instruments Comparator with Hysteresis Reference Design Visit Texas Instruments
    TIPD109
    Texas Instruments Simple Thermocouple Measurement Solution Reference Design, <1°C Accurate Visit Texas Instruments
    PCM1864LMBEVM
    Texas Instruments PCM1864-Based Linear Microphone Board (LMB) Reference Design Visit Texas Instruments Buy
    TIDA-00239
    Texas Instruments 14-Channel Active Cell Balance Battery Management Reference Design Visit Texas Instruments
    TIPD131
    Texas Instruments Single-Ended Input to Differential Output Conversion Circuit Reference Design Visit Texas Instruments

    Documents mentioning AMMETER DESIGN

    Document Partial File Text Tags Type PDF
    mic5331
    MIC5331 Evaluation Board Micro-Power High Performance Dual 300mA ULDO™ (2.3V ≤ VIN ≤ 5.5V). An ammeter may be placed between the input supply and the VIN terminal to the evaluation board to accurately monitor the input current. The ammeter and/or power lead
    Original PDF
    2279 Technical portal and online community for
    2279 Technical portal and online community for Design Engineers - www.element-14.com Panel Meters Page 4 to 20mA Process Indicators… Ammeter Shunts… Current Transformers (CT’s)…
    Original PDF
    43703
    DIN 43703 Shunts 860 Series Designed and manufactured to comply with the requirements of DIN43 703 this range of shunts provides an accurate D.C. millivolt signal, exactly proportional to the system current, to drive ammeter indicators, overload protection and
    Original PDF
    Installation Instructions for 249 PC Series
    Installation Instructions for 249 PC Series Pressure-to-Current Pressure Sensors ELECTRICAL CONNECTIONS An ammeter, resistor or any current sensing device is placed in series with a DC voltage source and the pressure sensor for proper operation. The load,
    Original PDF
    mic2290
    MIC2290 (APD) Evaluation Board 48V Avalanche Photo Diode (APD) Bias Circuit General Description 2. Connect the load to the VOUT (J4) and ground (J5) terminals. The load can be either passive (resistor) or active (electronic load). An ammeter can be placed between
    Original PDF
    ® DMS Accessories 4-Wire DC Current Shunts Order
    ® DMS Accessories 4-Wire DC Current Shunts Order on-line at www.datel.com POINTS TO KEEP IN MIND WHEN YOU USE A DC AMMETER SHUNT These shunts are designed for use with 50 or 100 millivolt measuring instruments, calibrated in terms of the ampere ratings of
    Original PDF
    ammeter
    Ammeter (moving iron) with switch Wiring Diagram A range of moving iron AC Ammeters with integral phase selection switch in 72 or 96mm square DIN format for use on AC supplies operating from current transformers with 5 amp or 1 amp secondaries. Specify the
    Original PDF
    APPLICATION NOTE M16C/26 Power Modes 1.0 Abstract
    APPLICATION NOTE M16C/26 Power Modes 1.0 Abstract The following article discusses the various power modes of the M30262 MCU. A sample program is available that runs on the MSV30262 SKP board for testing and evaluation. Using an ammeter connected to the JP1
    Original PDF
    mic2290
    MIC2290 Evaluation Board 1.2MHz PWM Step-Up Converter with Internal Schottky Diode General Description 2. Connect the load to the VOUT (J4) and ground terminals. The load can be either passive (resistor) or active (electronic load). An ammeter can be placed between the
    Original PDF
    MIC2811/21 Evaluation Board Four Output Power
    MIC2811/21 Evaluation Board Four Output Power Management IC with 2MHz, 600mA DC/DC and Triple 300mA LDOs of the evaluation board. Ensure that the supply voltage is monitored at the input terminals. The ammeter and/or power lead resistance can reduce the voltage supplied to the input.
    Original PDF
    ammeter
    METRACLIPâ60 Digital Clip-On Ammeter 3-348-983-03 2/7.00 Clip Functions 10 mA … 400.0 A • Alternating current measurement • 2 way clip sensor for cables of up to 24 mm diameter • Highly accurate measurement of alternating current independent of position of conductor within the clip
    Original PDF
    mic5332
    MIC5332 Evaluation Board Micro-Power High Performance Dual 300mA ULDO™ voltage is monitored at the VIN terminal, as the ammeter and/or power lead resistance can reduce the voltage supplied to the input. General Description The MIC5332 is a tiny dual low quiescent current LDO.
    Original PDF
    TEPRO DC Ammeter Shunts i s ELE C TR O TECH NIK
    TEPRO DC Ammeter Shunts i s ELE C TR O TECH NIK TEPRO has been producing high quality DC Am meter Shunts since 1959. Over the years we have produced and developed many "Industry Standard" shunts, along with an extensive line of custom application shunt devices.
    OCR Scan PDF
    mic2601
    MIC2601/2 Evaluation Board 1.2MHz/2MHz PWM DC/DC Boost Switching Regulator General Description 2. Connect the load to the VOUT (J4) and ground (J5) terminals. The load can be either passive (resistor) or active (electronic load). An ammeter can be placed between the load and the VOUT
    Original PDF
    APPLICATION NOTE H8/300H Tiny Series Ammeter
    APPLICATION NOTE H8/300H Tiny Series Ammeter Implementation Example Introduction There are a variety of methods of detecting current levels. In this example the DC current levels are measured using a shunt resistor and the A/D converter built into the H8/36014, which is the simplest and most basic method. The voltage
    Original PDF
    dpm812
    www.trumeter.com DPM812 | DPM822 33/4 digit panel meter with a 40 segment bargraph indication. The unit has a fully auto ranging DCV input to 300VDC and a selectable 4 scale DC ammeter upto 10ADC. DPM812 | 822 33/4 digit panel meter with a 40 segment bargraph indication. The unit has a fully auto
    Original PDF
    97cfdc
    5 4 3 SMSC - 97CFDC USB - FLOPPY CONTROLLER ASSY 6131 REV B 2 1 FLOPPY VDD_Floppy 33 31 29 27 25 23 21 19 17 15 13 11 9 7 5 3 1 JP4 R34 FMMT2222A 332 1/8W 1% VDD_3.3 3 AMMETER-SUPPLY SELECTION + C3 1.0uf 25V + - C4 4.7uF 16V 10% R5 1.0K 1% 2 1 1 1 DS0~ DSKCHG~
    Original PDF