Part Number
    Please enter a valid full or partial manufacturer part number with a minimum of 3 letters or numbers

    75 OHM RESISTOR Search Results

    Documents mentioning 75 OHM RESISTOR

    Document Partial File Text Tags Type PDF
    dsx-3
    DSX-3 application note 75 ohm Circuit Termination Overview DS3 Network Elements (NE) such as fiber optic terminals (FOT) or M13 multiplexers (M13) that are cabled to the DSX-3 require a 75 ohm load to stabilize the output signal. This 75 ohm load or "75 ohm termination" prevents the output from oscillating and affecting adjacent channels.
    Original PDF
    75 ohm coupler
    ISO 9001 CERTIFIED E-Series 75 Ohm Coupler 40 - 1000 MHz Features EMDC-20-2-75 SM-55 * Typical Coupling -20 dB * Surface Mount Description M/A-COM’s EMDC-20-2-75 is a 75 Ohm Non Directional Coupler, in a Low Cost, Surface Mount Package. Ideally used with a 75 Ohm
    Original PDF
    pe4272
    5 4 3 2 1 D D 75 OHM T-Line 75 OHM T-Line 1 1 2 J3 RF1 GND GND RF2 8 7 6 5 2 J1 VDD CTRL GND RFC U1 PE4272 C 4 GND GND VDD CTRL 1 R1 1M 2 1 J2 2 3 1 2 3 4 J6 HEADER 2X2 C 75 OHM T-Line C1 100pF C2 100pF B B 75 OHM T-Line J4 J5 NOTES: UNLESS OTHERWISE SPECIFIED
    Original PDF
    RF Coax Connectors BNC Connectors (50 ohm/75 ohm)
    RF Coax Connectors BNC Connectors (50 ohm/75 ohm) Product Facts ■ Bayonet lock coupling for quick connect/disconnect ■ Various connectors available in 50 and 75 ohm versions ■ Fully intermateable with comparable BNC UG/U connectors ■ Full range of Hex Crimp
    Original PDF
    WIRELESS, RF, AND CABLE Application Note 972: May
    WIRELESS, RF, AND CABLE Application Note 972: May 01, 2002 CATV Minimum Loss Pad for 75-ohm Measurements CATV systems based on 75-ohm transmission lines are measured with 50-ohm test equipment. This article derives the equations relating pad networks that allow proper
    Original PDF
    75 Ohm BNC Connectors BNC Adapters and Bulkheads
    75 Ohm BNC Connectors BNC Adapters and Bulkheads Features Improved performance – true 75 Ohm character impedance Outstanding electrical performance to 3 GHz Bulkhead feedthrough available with or without panel isolation Meets the performance requirements of MIL-A-55339 for radio
    Original PDF
    cbje130-2
    5 4 3 2 1 J6 HEADER 14 1 3 5 7 9 11 13 D 3 RF1 4 5 C1 GND 14 RF2 13 GND GND 12 GND GND 11 C2 DNI C3 DNI 75 OHM T-Line J3 CBJE130-2 GND 75 OHM T-Line 75 OHM T-Line J4 CBJE130-2 1 J5 CBJE130-2 UNLESS OTHERWISE SPECIFIED DIMENSIONS AND TOLERANCES ARE IN INCHES AND
    Original PDF
    BNC 75 OHM CONNECTOR PRODUCTS ADC's BNC
    BNC 75 OHM CONNECTOR PRODUCTS ADC's BNC Connectors are the most reliable and universally accepted method of terminating coaxial cable in the market today. Outstanding electrical performance (up to 3 GHz) is achieved by unique design elements in the industry's truest 75 ohm connector.
    Original PDF
    tat7466
    75 Ohm RF Amplifier 50-1300 MHz TAT7466 Advanced Product Information Overview The TAT7466 is a 75 Ohm RF Amplifier designed for use up to 1300 MHz. The TAT7466 contains two separate amplifiers for push pull applications. It is fabricated using 6-inch GaAs pHEMT technology to
    Original PDF
    tat7468
    75 Ohm RF Amplifier 50-1000 MHz TAT 7468B Preliminary Data Sheet Overview The TAT7468B is a 75 Ohm RF Amplifier designed for use to 1 GHz. The TAT7468B contains two separate amplifiers for push pull applications. It is fabricated using 6-inch GaAs pHEMT technology to
    Original PDF
    Connector Products 75 Ohm BNC Connectors ADC's
    Connector Products 75 Ohm BNC Connectors ADC's BNC connectors are the most reliable and universally accepted method of terminating coaxial cable in the market today. Outstanding electrical performance (up to 3 GHz) is achieved by unique design elements in the industry's truest 75 Ohm connector. Precision
    Original PDF
    tat7469
    75 Ohm RF Amplifier 50-1300 MHz TAT7469 Advanced Product Information Overview The TAT7469 is a 75 Ohm RF Amplifier designed for use up to 1300 MHz. The TAT7469 contains two separate amplifiers for push pull applications. It is fabricated using 6-inch GaAs pHEMT technology to
    Original PDF
    hmc348lp3
    HMC348LP3 / 348LP3E v05.0805 SWITCHES - SMT 8 GaAs MMIC SPDT NON-REFLECTIVE CATV SWITCH, DC - 2.5 GHz Typical Applications Features The HMC348LP3 / HMC348LP3E is ideal for: High Isolation: >80 dB @ 5 MHz (50 Ohm) >55 dB @ 1 GHz (50 Ohm) • 75 Ohm Systems
    Original PDF
    Surface Mount Directional Couplers 50/75Ω
    Surface Mount Directional Couplers 50/75Ω TCD-SERIES 5 to 1000 MHz Features • wide frequency range, 5-1000 MHz • 50 & 75 ohm versions • coupling from 9 to 20 dB • solder plated leads for excellent solderability • external resistor required, 50 or 75 ohms (size
    Original PDF
    hmc348lp3
    HMC348LP3 v04.0604 MICROWAVE CORPORATION GaAs MMIC SPDT NON-REFLECTIVE CATV SWITCH, DC - 2.5 GHz Typical Applications Features The HMC348LP3 is ideal for: High Isolation: >80 dB @ 5 MHz (50 Ohm) >55 dB @ 1 GHz (50 Ohm) • 75 Ohm Systems CATV Signal Distribution, Cable Modem
    Original PDF