59824-1 Tyco Amp
Abstract: 408-2823 59824-1 59824-1, 408-7424 crimping die ratchet 121-1136 HAND TERMINAL CRIMPING TOOL crimping tool E2004
Contextual Info: Instruction Sheet 408–2823 TETRA–CRIMP* Hand Crimping Tool 59824–1 05 JAN 04 Rev S PROPER USE GUIDELINES Cumulative Trauma Disorders can result from the prolonged use of manually powered hand tools. Hand tools are intended for occasional use and low volume
|
Original
|
|
PDF
|
408-7424
Abstract: UL-310 pull force requirements 408-7432 instructions 8082 Tyco 408-7424 faston crimp height tensile strength crimping pull test 567200-2 8082 codes ELT 406
Contextual Info: Application Specification 114- 13047 Budget FASTON* Receptacle Contacts 24 NOV 09 Rev A All numerical values are in metric units [with U.S. customary units in brackets]. Dimensions are in millimeters [and inches]. Unless otherwise specified, dimensions have a tolerance of +0.13 [+.005] and angles have a tolerance of +2_.
|
Original
|
|
PDF
|
tyco crimp height chart
Abstract: 408-7424 59824-1 solder crimp height faston crimp height general maintenance for applicators 58433-3 408-9640 59824-1 Tyco Amp 7432 Tyco 408-7424
Contextual Info: Application Specification 114-13076 PIDG* FASTON* Tabs and Fully-Insulated Receptacles NOTE 09 JAN 08 Rev A All numerical values are in metric units [with U.S. customary units in brackets]. Dimensions are in millimeters [and _ inches]. Unless otherwise specified, dimensions have a tolerance of +0.13 [+.005] and angles have a tolerance of +2 .
|
Original
|
|
PDF
|
567200-2
Abstract: 567200-3 59824-1 Tyco Amp 565435-5 59824-1 108103 checking terminal crimp height 408-7424 408-7278 408-1559 Tyco faston
Contextual Info: Application Specification Pre- Insulated Diamond Grip PIDG* FASTON* Receptacle Contacts NOTE i 114- 1002 16 NOV 09 Rev D All numerical values are in metric units [with U.S. customary units in brackets]. Dimensions are in millimeters [and inches]. Unless otherwise specified, dimensions have a tolerance of +0.13 [+.005] and angles have a tolerance of +2_.
|
Original
|
|
PDF
|
AMP 59974-1 crimper
Abstract: 59974-1 AMP crimper 59250 AMP 59170 567200-2 AMP 47387 crimper instruction sheet 408-6765 47387 AMP 59250 69051
Contextual Info: Application Specification PLASTI- GRIP* Terminals and Splices NOTE i 114- 2161 31 JUL 09 Rev E All numerical values are in metric units [with U.S. customary units in brackets]. Dimensions are in millimeters [and inches]. Unless otherwise specified, dimensions have a tolerance of +0.13 [+.005] and angles have a tolerance of +2_.
|
Original
|
22ATION
AMP 59974-1 crimper
59974-1
AMP crimper 59250
AMP 59170
567200-2
AMP 47387 crimper
instruction sheet 408-6765
47387
AMP 59250
69051
|
PDF
|
MIL-T-7928/1
Abstract: MIL-T-7928 408-7424 MS17182 AMP 47387 crimper checking terminal crimp height 408-7424 114-2157 59824-1 pull test 46121 crimping tool 59275
Contextual Info: Application Specification Pre-Insulated Diamond Grip PIDG* Terminals, Splices, and End Caps NOTE i 114-2157 09 SEP 08 Rev E All numerical values are in metric units [with U.S. customary units in brackets]. Dimensions are in millimeters [and inches]. Unless otherwise specified, dimensions have a tolerance of +0.13 [+.005] and angles have a tolerance of +2 .
|
Original
|
|
PDF
|
amp 408-1559
Abstract: 59824-1 Tyco Amp 818380-1 59824-1, 408-7424 59824-1 solder crimp height 567200-2 187 series faston tab bellmouth 408-7278 E-66717
Contextual Info: ti/ca/Electronics * A p p lica tio n S p e cification Pre-Insulated Diamond Grip PIDG* FASTON* Receptacle Contacts 114-1002 02 a u g 02 Rev c A ll numericai values are in metric units [with U.S. customary units in brackets]. Dimensions are in mliiimeters [and
|
OCR Scan
|
|
PDF
|
AMP 59974-1 crimper
Abstract: AMP crimper 69015 AMP 59170 46121 crimping tool 59974-1 AMP crimper 59250 AMP 59250 AMP 59239-4 crimper pneumatic tetra AMP crimper 59170
Contextual Info: Application Specification 114- 2161 PLASTI- GRIP* Terminals and Splices NOTE i 03 MAY 11 Rev F All numerical values are in metric units [with U.S. customary units in brackets]. Dimensions are in millimeters [and inches]. Unless otherwise specified, dimensions have a tolerance of +0.13 [+.005] and angles have a tolerance of +2_.
|
Original
|
|
PDF
|
