05G433FL Search Results

A3187

Contextual Info: 3185 t u r i 3189 *y J L r o tim i t i r « t w : n . m h k OPERATION +?•*■- 27609.2 H A U - E ì i l ì l l ' lATCUHS HALL-EFFECT LATCHES FOR HIGH-TEMPERATVBE OPERATION These Hall-effect latches are extremely temperature-stable and stress-resistant sensors especially suited for operation over extended

Contextual Info: BiMOS U 32-BIT SERIAL-INPUT, LATCHED DRIVERS Designed to reduce logic supply current, chip size, and system cost, the U C N 5833A /E P integrated circuits offer high-speed operation for thermal printers. These devices can also be used to drive multi­ plexed LED displays or incandescent lamps within their 125 mA peak

Contextual Info: 8-CHANNEL SATURATED SINK DRIVERS Low output-saturation voltages at high load currents are provided by UDN2596A and UDN2597A sink driver ICs. These devices can be used as interface buffers between standard low-power digital logic particularly MOS and high-power loads such as relays, solenoids,

Contextual Info: 2879 QUAD HIGH-CURRENT DARLINGTON SWITCHES These quad Darlington arrays are designed to serve as interface between low-level logic and peripheral power devices such as sole­ noids, motors, incandescent displays, heaters, and similar loads of up to 320 W per channel. Both integrated circuits include transientsuppression diodes that enable use with inductive loads. The input

Contextual Info: DUAL FULL-BRIDGE PWM MOTOR DRIVER PRi<: 1,1M i : \ A R V IN F O R M A T IO N Subject k? chan ge without noticc Sepicrnbcr !6 . 1997 The A2927SEB motor driver is designed to drive both windings of a bipolar stepper motor or bidirectionally control two dc motors. Both

Contextual Info: DUAL FVLL-BRIDGE M OTOR DRIVER As an interface between low-level logic and solenoids, brushless dc motors, or stepper motors, the UDN2998W dual full-bridge driver will operate inductive loads up to 50 V with continuous output currents of up to 2 A per bridge or peak start-up currents to 3 A. The control

Contextual Info: HALL-EFFECT SWITCHES FOR HIGH-TEMPERATVRE OPERATION These Hall-effect switches are monolithic integrated circuits with tighter magnetic specifications, designed to operate continuously over extended temperatures to +150°C, and are more stable with both temperature and supply voltage changes. The unipolar switching

Contextual Info: SMOKE DETECTOR WITH INTERCONNECT 1 2 7s~l DETECT. IN 16 T n ii 1 guard GUARD1 SENSITIVITY SET *TH OSC. CAP- 7T] HORN 2 lo i HORN1 9 1 - SUPPLY Owg. PC-004-1 The A5355CA is a low-current, CMOS circuit providing all of the required features for an ionization-type smoke detector. A networking

Contextual Info: BiMOS n 10-BIT SERIAL-INPUT, LATCHED SOURCE DRIVERS WITH ACTIVE-DMOS PULL-DOWNS UCN5810AF I OUT t I OUT« I SERIAL I DATA OUT LOAD SUPPLY I SERIAL 1DATA IN BLANKING OUT | The UCN5810AF, UCN5810EPF, and UCN5810LW F combine a 10-bit CMOS shift register and accompanying data latches, control

Contextual Info: blE D ALLEGRO MICROSYSTEMS INC • 5821 5823 QSQ433Ô 000b030 lt>7 ■ ALGR TIIRU BiMOS II 8-BIT SERIAL-INPUT, LATCHED DRIVERS A merged combination of bipolar and MOS technology gives these devices an interface flexibility beyond the reach of standard logic buffers and power driver arrays. The three devices in this series

Contextual Info: AM NOISE BLANKERS These noise blanker integrated circuits contain all of the necessary circuitry for adding an extremely efficient noise blanking technique patents pending to any type of AM tuner or receiver with RF input frequencies (or a first IF) to 30 MHz. The ULN3845A/LW features dual