-A&UUUUT- ELECTRICAL SPECIFICATIONS: OPERATING TEMPERATURE R

The Datasheet Archive - 100 Million Datasheets from 7500 Manufacturers.

-A&UUUUT- ELECTRICAL SPECIFICATIONS: OPERATING TEMPERATURE R

Datasheet Thumbnail

Top Searches for this datasheet

(P8>
-A&UUUUT-
ELECTRICAL SPECIFICATIONS:
OPERATING TEMPERATURE RANGE:
INDUCTANCE: (P6-J6) (P1-J1)
RESISTANCE: P6-J6 P3-J3 P2-J2
-<5mnr>-
+85"C
NDTEi
PINS ELECTRICALLY CONNECTED OMITTED.
@.01V, 10KHz
P1-J1
COMMON MODE: (-dB)
FREQUENCY (MHz) TYPICAL
THIS DRAWING SUBJECT MATTER SHOWN THEREON CONFIDENTIAL PROPERTY STEWART CONNECTOR SHALL REPRODUCED, COPIED, USED MANNER WITHOUT PRIOR WRITTEN C0NTEN1 STEWART CONNECTOR. SUBJECT MATTER PATENTED PATENT PENDING.
Stewart Connector
11118 Susquehanna Trail, South Glen Rock, 17327-9199 717.234.7512
MogJodf
http://www.stewartconneotor.com
SHEET
DRAWING
REV.
4.554 [115.67]
Part Number Stewart
-4.612 [117.14]-
t11-56! [13.97])TYP.
PIN:
.865 [21.97]
pillimi [umili |iiiiiiii|iiiiiiii^iiiiiiii j|iiiiiiii|iiiiiiii lillllllfp,
.275 .550
0.066 [1.68] .025 0.035 [0.89] (64)-
PIN:
[13.97] NON-ACCUM [1.27] NON-ACCUM [0.63] [2.54] NON-ACCUM
P.C.B. RECOMMENDED HOLE LAYOUT SEEN FROM COMPONENT SIDE TOLERANCE [0.08] UNLESS OTHERWISE SPECIFIED
[3.75] (20)
BOTTOM SURFACE JACK-(PCB SURFACE)
NOTES:
CONNECTOR MATERIALS: HOUSING: THERMOPLASTIC UL94 CONTACT/SHIELD: COPPER ALLOY SHIELD PLATING: NICKEL CONTACT PLATING: SELECTIVE GOLD, MICRO-INCHES
CONTACT AREA.
ELECTRICALLY CONNECTED MAYBE OMITTED. ELECTRICAL DRAWING OMITTED PINS.
TOLERANCES COMPLY WITH F.C.C. DIMENSION REQUIREMENTS.
TOLERANCES OTHERWISE SPECIFIED [0.13]
REFLOW WAVE SOLDER COMPATIBLE -260'C SECONDS MAX.
THIS DRAWING SUBJECT MATTER SHOWN THEREON CONFIDENTIAL PROPERTY STEWART CONNECTOR SHALL REPRODUCED, COPIED, USED MANNER WITHOUT PRIOR WRITTEN CONTENT STEWART CONNECTOR. SUBJECT MATTER PATENTED PATENT PENDING.
Stewart Connector
11118 Susquehanna Trail, South Glen Rock, 17327-9199 717.234.7512
MogJodf
http://www.stewartconneotor.com
SHEET
DRAWING
REV.
.000 (TOP BOTTOM OPENING) .010 [0.25] MAX. RADIUS(4)
SUGGESTED PANEL OPENING
POINT CONTACT WITH PANEL
.080 [2.03]
.275 [6.99]
SUGGESTED PANEL OPENING INTENDED GIVE USER ABILITY HAVE REASONABLE JACK PANEL CLEARANCES MAINTAIN RELIABLE GROUNDING CAPABILITY.
TOLERANCES OTHERWISE SPECIFIED [0.13]
THIS DRAWING SUBJECT MATTER SHOWN THEREON CONFIDENTIAL PROPERTY STEWART CONNECTOR SHALL REPRODUCED, COPIED, USED MANNER WITHOUT PRIOR WRITTEN CONTEN1 STEWART CONNECTOR. SUBJECT MATTER PATENTED PATENT PENDING.
Stewart Connector
11118 Susquehanna Trail, South Glen Rock, 17327-9199 717.234.7512
MogJodf
http://www.stewartconnector.com
SHEET
DRAWING
REV.

-A&UUUUT- ELECTRICAL SPECIFICATIONS: OPERATING TEMPERATURE R

Top Searches for this datasheet

Other recent searches