INDUCTANCE: (P3-J3) P4-J4) (P7-J7) 10KHz RESISTANCE: P8-J8 P

The Datasheet Archive - 100 Million Datasheets from 7500 Manufacturers.

INDUCTANCE: (P3-J3) P4-J4) (P7-J7) 10KHz RESISTANCE: P8-J8 P

Datasheet Thumbnail

Top Searches for this datasheet

ELECTRICAL SPECIFICATIONS:
INDUCTANCE: (P3-J3) P4-J4) (P7-J7)
10KHz
RESISTANCE: P8-J8 P7-J7 P6-J6 P3-J3 P5-J5 P4-J4
COMMON MODE ATTENUATION:
FREQUENCY (MHz) (-dB) TYPICAL (-dB)
THIS DRAWING SUBJECT MATTER SHOWN THEREON CONFIDENTIAL PROPERTY STEWART CONNECTOR
SHALL REPRODUCED, CDPIED, USED MANNER WITHOUT PRIOR WRITTEN CONTENT STEWART
CONNECTOR. SUBJECT MATTER PATENTED PATENT PENDING.
Stewart Connector
11118 Susquehanna Trail, South Glen Rock, 17327-9199 717.234.7512
MogJodf
http://www.stswartconnector.com
SHEET
DRAWING
REV.
.025 [0.63]
.275 .550
0.066 [1.68] .025 0.035 [0.89] (64)
PIN:
[3.251 .125 [118]
2.150 [54.61]-
-^550 [13.97] NON-ACCUM -.050 [1.27] NON-ACCUM [0.63] [Z54] NON-ACCUM
4.300 [109.22] -4.520 [114.81]
.145 [3.68] 0.085 [2.16]
P.C.B. RECOMMENDED HOLE LAYOUT SEEN FROM COMPONENT SIDE TOLERANCE [0.08] UNLESS OTHERWISE SPECIFIED
[3.75] (20)
[3.68] .040 [1.02X9) [Z12](9)
BOTTOM SURFACE JACK-(PCB SURFACE)
NOTES:
CONNECTOR MATERIALS:
HOUSING: THERMOPLASTIC UL94 CONTACT/SHIELD: COPPER ALLOY SHIELD PLATING: NICKEL CONTACT PLATING: SELECTIVE GOLD,
MICRO-INCHES MIN. CONTACT AREA.
ELECTRICALLY CONNECTED MAYBE OMITTED. ELECTRICAL DRAWING OMITTED PINS.
TOLERANCES COMPLY WITH F.C.C. DIMENSION REQUIREMENTS.
TOLERANCES OTHERWISE SPECIFIED [0.13]
WAVE SOLDER COMPATIBLE PREHEAT 125*C/90SECS.
THIS DRAWING SUBJECT MATTER SHOWN THEREON CONFIDENTIAL PROPERTY STEWART CONNECTOR
SHALL REPRODUCED, CDPIED, USED MANNER WITHOUT PRIOR WRITTEN CONTENT STEWART
CONNECTOR. SUBJECT MATTER PATENTED PATENT PENDING.
Stewart Connector
11118 Susquehanna Trail, South Glen Rock, 17327-9199 717.234.7512
MogJodf
http://www.stswartconnector.com
SHEET
DRAWING
REV.
POINT CONTACT WITH PANEL
.000 (TOP BOTTOM OPENING) -.010 MAX. RADIUS(4)
SUGGESTED PANEL OPENING
.275 [6.99]
SUGGESTED PANEL OPENING INTENDED GIVE USER ABILITY HAVE REASONABLE JACK PANEL CLEARANCES MAINTAIN RELIABLE GROUNDING CAPABILITY.
TOLERANCES OTHERWISE SPECIFIED [0.13]
THIS DRAWING SUBJECT MATTER SHOWN THEREON CONFIDENTIAL PROPERTY STEWART CONNECTOR
SHALL REPRODUCED, CDPIED, USED MANNER WITHOUT PRIOR WRITTEN CONTENT STEWART
CONNECTOR. SUBJECT MATTER PATENTED PATENT PENDING.
Stewart Connector
11118 Susquehanna Trail, South Glen Rock, 17327-9199 717.234.7512
MogJodf
http://www.stswartconnector.com
SHEET
DRAWING
REV.

INDUCTANCE: (P3-J3) P4-J4) (P7-J7) 10KHz RESISTANCE: P8-J8 P

Top Searches for this datasheet

Other recent searches