99800 Date Issue June 14,1990 Status Product Specification

The Datasheet Archive - 100 Million Datasheets from 7500 Manufacturers.

99800 Date Issue June 14,1990 Status Product Specification

Datasheet Thumbnail

Top Searches for this datasheet

Document 853-0616
99800
Date Issue June 14,1990
Status Product Specification
Products
PINS DESCRIPTION
D0-Ds Data Inputs
Qo-Qa Data Outputs
CONFIGURATIONS
VCC2
Vcct
VCC2
CERAMIC
100126
Backplane Driver
FEATURES
propagation delay: 2.0ns supply current (-iEE): 78mA
DESCRIPTION
100126 contains nine independent, high-speed buffer gates each with single input single output. gates non-inverting. These buffers useful bus-oriented systems where buffering desired. output transition times slower minimize noise when used backplane environment.
unused inputs left open integrated pull-down resistors.
DESCRIPTION
LOGIC DIAGRAM
IEC/IEEE SYMBOL
ORDERING INFORMATION
DESCRIPTION ORDER CODE
24-Pin Ceramic their (400 mils wide) 100126F
24-Pin Ceramic Flat Pack 100126Y
28-Pin PLCC 100126A
VCC2
VCC2
VCC2
D7VCC2VEE
fiMMMfifi
UleJliJH
Veti vcc2
VCC2
VCC2 Vcc2 Vccl
VcC2
VEEVCC2
VCC2
Philips Components Products Product Specification
Backplane Driver 100126
SIMPLIFIED SCHEMATIC
ABSOLUTE MAXIMUM RATINGS Veci Vcc2 ground, unless otherwise specified
SYMBOL PARAMETER LIMITS UNIT
Supply voltage range -7.0 +0.5
Input voltage should never more negative than VEE) +0.5
Output source current (continuous)
Storage temperature range +150
Maximum junction temperature
NOTE:
Operation beyond limits forth this table impair useful life device
OPERATING CONDITIONS
TEST LIMITS
SYMBOL PARAMETER CONDITIONS MIN. NOM. MAX. UNIT
Veci. VcC2 Circuit ground
Supply voltage -4.5 -4.2
Supply voltage when operating with 10KH family -5.7
-4-2V -1150
High level input voltage =-4.5V -1165 -880
-4-8V -1165
=-4.2V -1475
level input voltage -4.5V -1810 -1475
-4.8V -1490
Operating ambient temperature range
NOTE:
When operating other than specified voltages (-4.2V, -4.5V, -4.8V), electrical characteristics will vary slightly from their specified values.
June 1990
Philips Components Products
Product Specification
Backplane Driver 100126
ELECTRICAL CHARACTERISTICS Vcci Vcc2 ground, -4.8V -4.2V, unless otherwise
specified1-3-4
TEST LIMITS
SYMBOL PARAMETER CONDITIONS2 MIN. TYP. MAX. UNIT
-1020 -870
High level output voltage Inputs Vihmax Vilmin. -4.5 -1025 -955
-1035 -880
Apply Vihmin V|LMAxto -4.2V -1030
VoHT High level output threshold voltage Outputs input time, other -4.5 -1035
Loaded inputs Vihmax V|lmin- -4.8V -1045
with Apply Vihmin Vilmax -1595
Volt level output threshold voltage -2.0V input time, other -4.5V -1610
inputs Vihmax Vilmin -4.8V -1610
Vee=-4.2V -1810 -1605
level output voltage Inputs Vihmax V,lmin. -1810 -1705 -1620
-4.8V -1830 -1620
High level input current input under test Other inputs V|LMm.
level input current input under test VJLMin. Other inputs Vihmax.
-Iee supply current inputs Vihmax-
NOTES:
specified limits represent worst case values parameter. Since these worst case values normally occur supply voltage temperature extremes, additional noise immunity achieved decreasing allowable operating condition ranges.
Conditions testing shown tables necessarily worst case. worst case testing guidelines, refer Testing, Chapter Section
specified limits shown electrical characteristics table only after thermal equilibrium been established.
Thermal equilibrium established applying power least minutes, while maintaining transverse airflow meters/sec (500 linear feet/min) over device, mounted either test socket printed circuit board. Test voltage values given operating conditions table.
device function down -5.7V, allowing operation with either 10KH family. Correction factors used
calculate limits extended range. more information, Chapters Section
ELECTRICAL CHARACTERISTICS
Ceramic VCci Vcc2 ground, -4.8V -4.2V
LIMITS
SYMBOL PARAMETER TEST CONDITION UNIT
MIN. MAX. MIN. MAX. MIN. MAX.
tplh <phl Propagation delay Waveform 1.05 1.05 2.75 2.75 1.05 2.75 2.75 1.05 1.05 2.75 2.75
Transition time 1.15 1.15 3.30 3.30 1.15 1.15 3.30 3.30 1.05 1.05 3.30 3.30
NOTE:
test setup information, Testing, Chapter Section
June 1990
Philips Components Products Product Specification
Backplane Driver 100126
ELECTRICAL CHARACTERISTICS
Ceramic Vcc, Vcc2 ground, -5.2V
LIMITS
SYMBOL PARAMETER TEST CONDITION UNIT
MIN. MAX. MIN. MAX. MIN. MAX.
tplh tphl Propagation delay Waveform 1.05 1.05 2.75 2.75 1.05 1.05 2.75 2.75 1.05 1.05 2.75 2.75
>tlh tthl Transition time 1.15 1.15 3.30 3.30 1.15 1.15 3.30 3.30 1.05 1.05 3.30 3.30
NOTE:
test setup information, Testing, Chapter Section
ELECTRICAL CHARACTERISTICS
Flat Pack PLCC VCC1 Vcc2 ground, -4.8V -4.2V
LIMITS
SYMBOL PARAMETER TEST CONDITION UNIT
MIN. MAX. MIN. MAX. MIN. MAX.
iplh 'phl Propagation delay Waveform 1.05 2.55 2.55 1.05 1.05 2.55 2.55 1.05 1.05 2.55 2.55
'tlh <thl Transition time 1.15 1.15 3.30 3.30 1.15 1.15 3.30 3.30 1.05 1.05 3.30 3.30
NOTE:
test setup information, Testing, Chapter Section
ELECTRICAL CHARACTERISTICS
Flat Pack PLCC VCC1 Vcc2 ground, -5.2V
limits
symbol parameter test condition unit
min. max. min. max. min. max.
tPLH <PHL Propagation delay Waveform 1.05 1.05 2.55 2.55 1.05 1.05 2.55 2.55 1.05 1.05 2.55 2.55
tTLH 'thl Transition time 1.15 1.15 3.30 3.30 1.15 1.15 3.30 3.30 1.05 3.30
NOTE:
test setup information, Testing, Chapter Section
WAVEFORMS
OUTPUTS
'THL
tTLH
Waveform Propagation Delay Transition Times
NOTE:
power signal voltages shifted 2.0V bench test purposes.
June 1990

99800 Date Issue June 14,1990 Status Product Specification

Top Searches for this datasheet

Other recent searches