99800 Date Issue June 1990 Status Product Specification

The Datasheet Archive - 100 Million Datasheets from 7500 Manufacturers.

99800 Date Issue June 1990 Status Product Specification

Datasheet Thumbnail

Top Searches for this datasheet

Document 853-0610
99800
Date Issue June 1990
Status Product Specification
Products
100117
Triple 1-2-2 Input OR-AND/ OR-AND-INVERT Gate
propagation delay: 1.4ns data inputs, 0.75ns Enable Inputs supply current (-lEE): 57mA
DESCRIPTION
100117 three OR/AND gates with True Complementary outputs.
unused Inputs left open integrated pull-down resistors.
DESCRIPTION
ORDERING INFORMATION
IEC/IEEE SYMBOL
PINS DESCRIPTION
DA2, DB2, DC2, Data Inputs
Enable Inputs
QO-Q2 True Data Outputs
a0-a2 Complementary Data Outputs
DESCRIPTION ORDER CODE
24-Pin Ceramic (400 mils wide) 100117F
24-Pin Ceramic Flat Pack 100117Y
28-Pin PLCC 100117A
CONFIGURATIONS
DAoH RHHRHR
Veci VCC2 CERAMIC FLAT PACK
feil
Vce,
vcc2 Vcc2 Vcct
MMMMIIB
Philips Components Products
Product Specification
Gate
100117
LOGIC DIAGRAM
FUNCTION TABLE
INPUTS OUTPUTS
NOTES:
High voltage level voltage level Don't care
SIMPLIFIED SCHEMATIC
ABSOLUTE MAXIMUM RATINGS Vcci vcc2 ground, unless otherwise specified.
SYMBOL PARAMETER LIMITS UNIT
Supply voltage range -7.0 to+0.5
Input voltage (Vin should never more negative than Vee) +0.5
Output source current (continuous)
Storage temperature range to+150
Maximum junction temperature
NOTE:
Operation beyond limits forth this table impair useful life device
June 1990
Philips Components Products Product Specification
Gate 100117
OPERATING CONDITIONS
SYMBOL PARAMETER TEST CONDITIONS LIMITS UNIT
MIN. NOM. MAX.
vcc1. vcc2 Circuit ground
Supply voltage -4.5 -4.2
Supply voltage when operating with 10KH family -5.7
High level input voltage -4.2V -1150 -880
-4-5V -1165
-4.8 -1165
level input voltage =-4.2V -1810 -1475
-1475
-1490
Operating ambient temperature range
NOTE:
When operating other than specified voltages (-4.2V, -4.5V, -4.8V), electrical characteristics will vary slightly from their specified values.
ELECTRICAL CHARACTERISTICS VCC1 Vcc2 ground, -4.2V, unless otherwise
specified1'34
TEST LIMITS
SYMBOL PARAMETER CONDITIONS2 MIN. TYP. MAX. UNIT
-1020 -870
High level output voltage Inputs V(HMAXor V|LMin. -4.5 -1025 -955 -880
-1035 -880
Apply V,HM|NorV|LMAXto -4.2V -1030
voht High level output threshold voltage Outputs Input time, other =-4.5V -1035
loaded inputs Vihmax Vilmin- -4.8V -1045
with Apply V|HM,N V,LMAX -4.2V -1595
Volt level output threshold voltage Input time, other -4-5V -1610
Inputs Vihmax V|LM!N. -1610
-4.2V -1810 -1605
level output voltage Inputs VIHmax V|LM|N. -1810 -1705 -1620
-4.8 -1830 -1620
High level input current input under test V,hmax Other inputs V1LM|N.
level Input current input under test V|LM|N. Other inputs Vihmax-
-Iee supply current inputs V|HMAx-
NOTES:
specified limits represent worst case values parameter. Since these worst case values normally occur supply voltage temperature extremes, additional noise immunity achieved decreasing allowable operating condition ranges.
Conditions testing shown tables necessarily worst case. worst case testing guidelines, refer Testing, Chapter Section
specified limits shown electrical characteristics table only after thermal equilibrium been established.
Thermal equilibrium established applying power least minutes, while maintaining transverse airflow meters/sec (500 linear feet/min) over device, mounted either test socket printed circuit board. Test voltage values given operating conditions table.
device function down -5.7V, allowing operation with either 10KH family Correction factors used
calculate limits extended range. more information, Chapters Section
June 1990
Philips Components Products Product Specification
Gate 100117
ELECTRICAL CHARACTERISTICS
Ceramic Vcci Vcc2 ground, -4.8V -4.2V
LIMITS
SYMBOL PARAMETER TEST CONDITION UNIT
MIN. MAX. MIN. MAX. MIN. MAX.
tpLH tpHL Propagation delay DCn, 0.90 0.90 2.60 0.90 0.90 2.50 2.50 0.90 0.90 2.60 2.60
tPLH tpHL Propagation delay Waveform 0.45 0.45 1.40 1.40 0.45 0.45 1.30 1.30 0.45 0.45 1.40 1.40
tTHl Transition time 0.45 1.20 1.20 0.45 0.45 1.10 1.10 0.45 0.45 1.20
NOTE:
test setup information, Testing, Chapter Section
ELECTRICAL CHARACTERISTICS
Ceramic VCC1 Vcc2 ground -5.2V
LIMITS
SYMBOL PARAMETER TEST CONDITION UNIT
MIN. MAX. MIN. MAX. MIN. MAX.
fplh iphl Propagation delay DDn, 0.90 0.90 2.60 2.60 0.90 0.90 2.50 2.50 0.90 2.60 2.60
iplh <phl Propagation delay Waveform 0.45 0.45 1.40 1.40 0.45 1.30 1.30 0.45 0.45 1.40 1.40
'thl Transition time 0.45 0.45 1.20 1.20 0.45 0.45 1.10 1.10 0.45 0.45 1.20 1.20
NOTE:
test setup information, Testing, Chapter Section
ELECTRICAL CHARACTERISTICS
Flat Pack PLCC Vcci VCc2 ground, -4.8V -4.2V
limits
symbol parameter test condition unit
min. max. min. max. min. max.
'plh tphl Propagation delay DCn, DDn, 0.90 0.90 2.40 2.40 0.90 0.90 2.30 2.30 0.90 0.90 2.40 2.40
tplh Propagation delay Waveform 0.45 0.45 1.20 1.20 0.45 0.45 1.10 1.10 0.45 0.45 1.20 1.20
Transition time 0.45 0.45 1.20 1.20 0.45 0.45 1.10 1.10 0.45 0.45 1.20 1.20
NOTE:
test setup information, Testing, Chapter Section
June 1990
Philips Components Products
Product Specification
Gate
100117
ELECTRICAL CHARACTERISTICS
Flat Pack PLCC Vcci Vcc2 ground,
LIMITS
SYMBOL PARAMETER TEST CONDITION UNIT
MIN. MAX. MIN. MAX. MIN. MAX.
tpLH tPHL Propagation delay 0.90 0.90 2.40 2.40 0.90 0.90 2.30 2.30 0.90 0.90 2.40 2.40
tpLH Propagation delay Waveform 0.45 0.45 1.20 1.20 0.45 0.45 1.10 1.10 0.45 0.45 1.20 1.20
tTLH <THL Transition time 0.45 0.45 1.20 1.20 0.45 0.45 1.10 1.10 0.45 0.45 1.20 1.20
NOTE:
test setup information, Testing, Chapter Section
WAVEFORMS
INPUTS
OUTPUTS
OUTPUTS
20%-
<PLH
Waveform Propagation Delay Transition Times
NOTE:
power signal voltages shifted 2.0V bench test purposes.
June 1990

99800 Date Issue June 1990 Status Product Specification

Top Searches for this datasheet

Other recent searches