13256 98th Street Lenexa, 66215 (800) 492-2320 www.aerocomm.com w

The Datasheet Archive - 100 Million Datasheets from 7500 Manufacturers.

13256 98th Street Lenexa, 66215 (800) 492-2320 www.aerocomm.com w

Datasheet Thumbnail

Top Searches for this datasheet

SDK-LX2400 Development Users Manual
13256 98th Street Lenexa, 66215 (800) 492-2320
www.aerocomm.com wireless@aerocomm.com
DOC:601JDSR1
Copyright Information
Copyright Information
Copyright 2000 AEROCOMM Inc. rights reserved. information contained this manual accompanying software programs copyrighted rights reserved AEROCOMM Inc. AEROCOMM Inc. reserves right make periodic modifications this product without obligation notify person entity such revision. Copying, duplicating, selling, otherwise distributing part this product without prior consent authorized representative AEROCOMM Inc. prohibited. brands product names this publication registered trademarks trademarks their respective holders.
DOC:601JDSR1
Revision Version
Description Initial Release Version 6/01/00
Copyright 2000 AeroComm, Inc. This material preliminary. Information furnished AeroComm this specification believed accurate. Devices sold AeroComm covered warranty patent indemnification provisions appearing Terms Sale only. AeroComm makes warranty, express, statutory, implied description, regarding information forth herein. AeroComm reserves right change specifications time without notice. AeroComm's products intended normal commercial applications. Applications requiring extended temperature range unusual environmental requirements such military, medical life-support life-sustaining equipment, specifically recommended without additional testing such application.
DOC:601JDSR1
Table Contents
OVERVIEW.5 MECHANICAL OVERVIEW.6
SERIAL DAPTER BOARD 2.1.1 Status LED's. 2.1.2 Switch Settings Their Definitions Connection diagram LX2400 Serial Interface Board SOFTWARE OVERVIEW.9 OEM.EXE.9 Transmit/Receive Emulator.10 Single Line Command Interface.10 EEPROM Viewer/Editor.10 PORTS.CFG.10
3.1.1 3.1.2 3.1.3
ANTENNA BOARD.10 POWER SUPPLY SPECIFICATION.11
DOC:601JDSR1
Overview
Overview
This document contains information about hardware software included part AeroComm LX2400S transceiver SDK. designed allow flexibility hardware interface level that interfaced product, performance testing, other device that will support either level signals RS-232 Level Signals. SDK-LX2400S (Serial) Developer Kits help system designers implement transceiver designs quickly. offers cables, power supplies, circuit schematics, documentation accessories needed begin using LX2400 quickly. includes: LX2400 Data Transceivers Serial Adapter Boards with 40-pin interface, 40-pin header, power connector connector Power Adapters cables Hardware software interface specification WCP-2400-MMCX antennas (microstip antenna optional) (Antenna integrated LX2400) Software utilities Technical Support
DOC:601JDSR1
Developers
Mechanical Overview
LX2400 measures 1.65" 2.65". Critical parameters follows: interface connector (Amp 177986-1) mates with 177985-1 Mounting holes 0.100" diameter.
Figure Mechanical Overview LX2400
DOC:601JDSR1
Developers
Serial Adapter Board
Serial Adapter Board allows different forms communication with transceivers. user must choose between using RS-232 levels Volt logic levels interfacing with transceiver when using adapter board.
Figure Serial Adapter Board Assembly Drawing
serial interface adapter system developer provided that developer standard serial port exercise transceivers system integration. serial interface adapters have many features added them enhance their functionality well their usability. serial adapter boards have LED's placed edge board that glance, configuration operation serial adapter board will evident. Also, serial board communicate both RS-232 Levels.
DOC:601JDSR1
Developers 2.1.1 Status LED's
Reset This will light when Reset line processor high, transceiver being reset. This will light when power applied serial adapter board. This will light when low, should show activity when data transmitted host. This will light when low, should show activity when data received from host. In_Range This will light client transceiver range server transceiver with same system same channel. 9600 Baud This will light when 9600 baud line low, show that switches force transceiver into 9600 baud mode. PKTMODE This will light when line active. RS232 This will light when serial interface board configured convert RS-232 levels DB-9 transceiver level interface. This will light when serial interface board configured interface (computer) device DB-9 connector. Wr_Enable This will light when Write Enable line goes allowing EEPROM written
2.1.2 Switch Settings Their Definitions
DTE/DCE When this switch moved position (High) serial interface will configured (modem) connected (PC). When switch moved position (Low) serial interface will configured (PC) connected (modem). TTL/RS-232 When this switch (High) serial adapter will support level communications from DB-9 Serial interface transceiver addition, jumpers must installed). When switch (Low) serial adapter will support RS-232 level communications from DB-9 serial interface transceiver (NOTE: Never install jumpers when serial interface board configured support -232 levels). 40-pin header strip will always TTL(5V levels) 9600 baud When this switch (High) transceiver baud rate configured EEPROM. When switch (Low) transceiver forced 9600 baud. PKTMODE This switch used this revision RESET This pushbutton used provide hardware reset LX2400 transceiver Wr_Enable When this pushbutton pressed, will write enable EEPROM LX2400 transceiver. This button must pressed held during write process. Config/Normal This slide switch MUST Config. This will connect DB-9 connector (pin transceiver.
DOC:601JDSR1
Developers 2.1.3 Connection diagram LX2400 Serial Interface Board
Name TST_MODE WR_ENA UP_RESET PLL_LOCK RSSI IN_RANGE LX2400 Serial Interface Board 10,11 3,39 5,16 1,40 20(GND)
Software Overview
developer includes 3.5" diskette software utilities allowing customer exercise transceivers upon receipt. software utilities written environment. software utilities will operate properly under shell Windows Windows all. software includes several files follows: OEM.EXE Interactive Command/EE Edit Software/Transmit Receive Emulator. PORTS.CFG port address baud rate information LX0.CFG Configuration file OEM.EXE LXRWSP.INI AeroComm Only
These files located each directories follows: ClientPC- This directory contains Client Transceiver files that required Client Transceiver Server Transceiver separate Client Transceiver should connected (3F8) ServerPC- This directory contains Server Transceiver files that required Client Transceiver Server Transceiver separate Server Transceiver should connected (3F8)
OEM.EXE
This software contains three unique utilities exercise, monitor setup modes transceivers. These utilities are: Transmit/Receive Emulator, Single line command interface, EEPROM viewer/editor.
DOC:601JDSR1
Developers 3.1.1 Transmit/Receive Emulator
This utility allows Server Client transceiver communicate with each other. software comes pre-configured transceivers development kit. Connect Server Transceiver (3F8) connect Client Transceiver (3F8) separate Copy ClientPC directory contents with Client Transceiver attached. Copy ServerPC directory contents with Server Transceiver attached. TX/RX emulator uses script files (.RTC files) send compare data through transceiver link. operate transmit/receive emulator, there only commands used. `F4' This will clear emulator's buffers. `F5' This will change software Single Line Command Editor. `F9' This will execute chosen script file continuous loop. `F10' This will single step through script file. load script file run, will command `Alt then choose load script file. then press 'enter' will list script files that run. From here arrow keys select script file would like run. following script files have been included used specifically transmit/receive emulator. LXRXPKT.RTC This file used either client server transceiver receive data. LXTXPKT.RTC This file used either client server transceiver transmit data.
3.1.2 Single Line Command Interface
While Transmit/Receive emulator press `F5' enter into Line Command Interface. line command interface allows user easy issue LX2400 commands. These commands stored retrieved later during development. Several most commonly used commands such Enter Command Mode Read Client/Server have already been entered into Single Line Command Interface. `F10' used transmit command transceiver, `F9' command used repeatedly send command transceiver. Upon successfully receiving executing command, transceiver will send back acknowledgement displayed "Receive Data" window. exit, changes command interface either saved ignored. Press `Esc' exit.
3.1.3 EEPROM Viewer/Editor
From Single Line Command Interface, press `F2' into EEPROM Viewer/Editor. edit value this screen, simply move cursor highlight appropriate value, type value press `Enter' key. undo edit, press `Esc' before write values EEPROM. update transceiver with EEPROM values, first, must press hold write enable switch (SW2) then, press `F10' transmit data EEPROM.
PORTS.CFG
PORTS.CFG contains basic configuration information AeroComm software. contains port address hex, what software will consider Port (Default Port (Default also contains baud rate program will startup.
Antenna Board
DOC:601JDSR1
Developers
developer kits provided with microstrip antennas, NZH2400. dimensions NZH2400 1.65" 0.67" without interface connector. Optional antennas available testing. Antenna selection instrumental will impact overall system performance.
Power Supply Specification
power supplies also provided power both units developer kit. These supplies rated regulated 6Vdc 50mV ripple 300ma.
DOC:601JDSR1

13256 98th Street Lenexa, 66215 (800) 492-2320 www.aerocomm.com w

Top Searches for this datasheet

Other recent searches