Dual Advanced Source-Sink Linear Controller Regulated Voltages pr
|
|
|
Top Searches for this datasheet
APW7047
Dual Advanced Source-Sink Linear Controller
Regulated Voltages provided
General Description
APW7047 provides power controls protections three output voltages AGP/PCI Graphic Card applications. integrates controllers SOURCE-SINK linear controller, well monitor protection functions into single package. converter (PWM1) regulates VCORE(1.5V) with SYNC. buck converter. other standard buck converter (PWM2) regulates VMEM(2.5V) power memory. SOURCE-SINK linear controller control external MOSFETs linear regulator with capability sourcing sinking current. regulates (1.25V) power Termination voltage. Additional built-in over-voltage protection (OVP) will started when VCORE VMEM output above 115% each setting (VCORE VMEM). function will shutdown output voltages until re-powering each converter, over-current function monitors output current sensing voltage drop across MOSFET`s rDS(ON) eliminating need current sensing resistor.
SYNC. Buck Converter VCORE
(1.15V~1.50V)
Standard Buck Converter VMEM
(2.40V~2.75V)
-Linear Controller with SOURCE-SINK
Regulation VTT(1.25V)
Simple Single-Loop Control Design
Voltage-Mode Control
Excellent Output Voltage Regulation
VCORE Output Over Temperature VMEM Output Over Temperature Output ±25mV Over
Temperature Min. 1.7V
Fast Transient Response
Built-in Feedback Compensation Full 100% Duty Ratio Over-Voltage Over-Current Fault Monitor Constant Frequency Operation(200kHz) pins, SOIC Package
Description
UGATE BOOT
UGATE PHASE2 PHASE2 LGATE1 MEM2 MEM1 MEM0 CORE2 CORE1 CORE0 OCSET2
UGATE
Applications
Power Regulation AGP/PCI Graphics Power Regulation SSTL-2 Termination
PHASE1
URCE SINK
OCSET1
ANPEC reserves right make changes improve reliability manufacturability without notice, advise customers obtain latest version relevant information verify before placing orders. Copyright ANPEC Electronics Corp. Rev.A.1 May., 2002 www.anpec.com.tw
APW7047
Ordering Marking Information
APW7047
Handling Code Temp. Range Package Code Package Code SOP-24 Temp. Range Handling Code Tube
Tape Reel
APW7047K
APW7047 XXXXX
XXXXX Date Code
Block Diagram
28µA OVP1
200µA PHASE1
115%
VSEN1
CORE
CORE0 CORE1 CORE2 VSEN2
illa
SOURCE OVP2 115%
PGND PHASE2
200uA
Absolute Maximum Ratings
Symbol TSTG Supply Voltage Input Output Voltage Operating Ambient Temperature Junction Temperature Storage Temperature Soldering Temperature
Parameter
Rating -0.3 +0.3 Range Range Range +150 seconds
Unit
www.anpec.com.tw
Copyright ANPEC Electronics Corp. Rev. Rev.A.1 May., 2002
APW7047
Thermal Characteristics
Symbol Parameter Thermal Resistance Free SOIC SOIC (with 3in2 Copper) Value Unit °C/W
Electrical Characteristics
Unless otherwise specified, these specifications apply over VCC=VBOOT=12V TA=0~70°C. Typical values refer TA=25°C.
urren utdo urren 0V,U Test itio
er-o eset isin alling hresho Voltage scillator ning ency plitu ntroller ltag efere CORE Inpu Inpu efere ntro ller gulation Voltag accuracy rive rrent rive urre
Copyright ANPEC Electronics Corp. Rev. Rev.A.1 May., 2002
Vocse Vocse
-2.0
+2.0
-2.0 urcing inkin rrent +2.0
0.5V
www.anpec.com.tw
APW7047
Electrical Characteristics (Cont.)
Unless otherwise specified, these specifications apply over VCC=VBOOT=12V TA=0~70°C. Typical values refer TA=25°C.
Symbol Parameter Test Conditions VIN=2.5V VCC=12V VUGATE1,2=6V VCC=12V,VUGATE1,2=6V Min. APW7047 Typ. Max. Unit
IVIN Input Bias Current Controllers Gate Drivers IUGATE RGATE Protection VSEN1,2 trip point (VSEN1/VCORE VSEN2/VMEM VSEN1,2 O.V. Hysteresis IOCSET Ocset Current Source Soft start Current UGATE1,2 Source, LGATE1 Source UGATE1,2 Sink, LGATE1 Sink
0.74
VSEN Rising
Vocset=3V
Functional Description
(Pin Provide +12V bias supply this pin. This also provides gate bias charge MOSFETs SOURCE-SINK regulator. voltage this monitored Power-On Reset (POR) purposes. UGATE1 (Pin Connect this upper MOSFET gate PWM1 converter. This provides gate drive MOSFET. PHASE1 (Pin Connect this PWM1 converter's upper MOSFET source.This used monitor voltage drop across MOSFET over-current protection. (Pin Connect capacitor from this ground.This capacitor, along with internal 28uA current source,
Copyright ANPEC Electronics Corp. Rev. Rev.A.1 May., 2002
sets soft-start interval power controls preventing outputs from overshoot well limiting input current (Pin shuts down power outputs. compatible logic level high signal applied this immediately discharges soft-start capacitor,disabling power outputs. When re-enabled, undergoes soft-start cycle. Left open, this pulled internal pull-down resistor, enabling operation. SOURCE (Pin Connect this upper MOSFET gate drive SOURCE-SINK regulator. This drives upper external MOSFET sourcing regulator. SINK (Pin Connect this lower MOSFET gate drive
www.anpec.com.tw
APW7047
Functional Description (Cont.)
SOURCE-SINK regulator. This drives lower external MOSFET sinking regulator. (Pin Connect this output SOURCE-SINK regulator. This provides voltage feedback path sourcing sinking regulators. This internally connected negative input SOURCE controller, also connected positive input SINK controller. (Pin Connect this VMEM fixed voltage source. voltages, about 0.5VIN, generated internal resistor divider reference voltages sourcing sinking regulators. sinking regulation voltage higher than sourcing prevent direct current path through upper lower MOSFETs. OCSET1 (Pin Connect resistor (ROCSET from this drain PWM1 converter's MOSFET. ROCSET, internal 200uA current source (IOCSET MOSFET's onresistance(rDS(ON)) converter's over-current (OC) trip point according following equation:
OCSET
(Pin Signal ground voltage levels measured with respect this pin. VSEN2 (Pin This connected PWM2 converter's output voltage provide voltage feedback path. overvoltage protection(OVP) comparator uses this monitor output voltage over- voltage protection. OCSET2 (Pin
Connect resistor (ROCSET from this drain PWM2 converter's MOSFET. function this similar OCSET1(pin detection purposes.
CORE0-2 (Pin 15-17) CORE0-2 TTL-compatible logic level input pins 3-bit DAC. states three pins internal reference voltage (VCORE) PWM1 converter also threshold voltage PWM1 converter. MEM0-2 (Pin 18-20) MEM0-2 TTL-compatible logic level input pins other 3-bit DAC. states three pins internal reference voltage (VMEM) PWM2 converter also threshold voltage PWM2 converter. PGND (Pin Connect this anode flywheel diodes converters. LGATE1 (Pin Connect this Lower MOSEFT gate PWM1 converter. This provides gate drive MOSFET.
IPEAK
over-current trip cycles soft-start function. voltage this monitored Power-On Reset (POR) purposes. VSEN1 (Pin This connected PWM1 converter's output voltage provide voltage feedback path. overvoltage protection(OVP) comparator uses this monitor output voltage over- voltage protection
Copyright ANPEC Electronics Corp. Rev. Rev.A.1 May., 2002
www.anpec.com.tw
APW7047
Functional Description
PHASE2 (Pin Connect this PWM2 converter's MOSFET source.This used monitor voltage drop across MOSFET over-current protection. UGATE2 (Pin Connect this MOSFET gate PWM2 converter. This provides gate drive MOSFET.
Table Table
CORE2
Name CORE1 CORE0
VCORE Voltage 1.15 1.20 1.25 1.30 1.35 1.40 1.45 1.50
MEM2
Name MEM1
MEM0
VMEM Voltage 2.40 2.45 2.50 2.55 2.60 2.65 2.70 2.75
Simplified Power System Diagram
Standard Conv erter (PWM2)
VMEM
7047
3.3V
Conv erter (PWM1)
CORE
SOURCE-SINK Linear Conv erter
Copyright ANPEC Electronics Corp. Rev. Rev.A.1 May., 2002
www.anpec.com.tw
APW7047
Typical Application Circuit
+12V
10uF
200pF 1.5K
200pF 1.5K
+3.3V
10uF 330uF 10uF 330uF 10uF
4.7uH
PM4430 PM4430
PM9410 MBRD835L
7.8uH
VCORE
330uF 330uF
VMEM
VSEN
VSEN
330uF
VMEM
330uF PM7313
MEM2 MEM1 MEM0 CORE2 CORE1 CORE0
0.1uF
330uF
0.68uF
C10, C13, 330uF/6.3V tantalum Capacitor
Copyright ANPEC Electronics Corp. Rev. Rev.A.1 May., 2002
www.anpec.com.tw
APW7047
Typical Performance
SOURCE-SINK Linear Regulator Transient Response output capacitor 330uF (Low tantalum capacitor) Define output cerrent (IVTT) sourcing from regulator positive. interval current transitions figures smaller than 1uS. figure IVTT transition from -0.2A figure IVTT transition from 0.2A -4A.
Figure
Figure
Copyright ANPEC Electronics Corp. Rev. Rev.A.1 May., 2002
www.anpec.com.tw
APW7047
Packaging Information
300mil Reference JEDEC Registration MS-013)
GAUGE PLANE
Millimeters Min. 2.35 0.10 0.33 7.40 0.40 Max. 2.65 0.30 0.51 7.60 10.65 1.27
Variations- Variations SO-16 SO-18 SO-20 SO-24 SO-28 SO-14 Min. 10.10 11.35 12.60 15.20 17.70 8.80 Max. 10.50 11.76 15.60 18.11 9.20
Inches Min.
Variations- Max. Variation Min. Max. SO-16 SO-18 SO-20 SO-24 SO-28 SO-14 0.398 0.447 0.496 0.599 0.697 0.347 0.413 0.463 0.512 0.614 0.713 0.362
0.093 0.1043 0.004 0.0120 0.013 0.020 variations 0.2914 0.2992 0.050BSC 0.394 0.016 0.419 0.050
variations 1.27BSC
variations
variations
Copyright ANPEC Electronics Corp. Rev. Rev.A.1 May., 2002
www.anpec.com.tw
APW7047
Physical Specifications
Terminal Material Lead Solderability Solder-Plated Copper (Solder Material 90/10 63/37 SnPb) Meets Specification RSI86-91, ANSI/J-STD-002 Category
Reflow Condition
(IR/Convection Reflow)
Reference JEDEC Standard J-STD-020A APRIL 1999
temperature
Peak temperature
183°C Pre-heat temperature
Time
Classification Reflow Profiles
Convection Convection Average ramp-up rate(183°C Peak) 3°C/second max. seconds Preheat temperature 25°C) seconds Temperature maintained above 183°C Time within actual peak temperature seconds Peak temperature range +5/-0°C +5/-0°C Ramp-down rate /second max. minutes max. Time 25°C peak temperature /second max.
seconds 215-219°C +5/-0°C /second max.
Package Reflow Conditions
pkg. thickness 2.5mm bgas Convection +5/-0 215-219 IR/Convection +5/-0 pkg. thickness 2.5mm pkg. volume pkg. thickness 2.5mm pkg. volume Convection +5/-0 +5/-0 IR/Convection +5/-0
www.anpec.com.tw
Copyright ANPEC Electronics Corp. Rev. Rev.A.1 May., 2002
APW7047
Reliability test program
Test item SOLDERABILITY HOLT Latch-Up Method MIL-STD-883D-2003 MIL-STD-883D-1005.7 JESD-22-B, A102 MIL-STD-883D-1011.9 MIL-STD-883D-3015.7 JESD Description 245°C 1000 Bias Hrs, 121°C -65°C 150°C, Cycles VHBM 2KV, 200V 10ms 100mA
Carrier Tape Reel Dimensions
Application
330±1
±1.5
12.75 0.15
24.4
1.75±
SOP-
11.5 1.55 +0.1 1.5+ 0.25
10.9 15.9±
3.1± 0.35±0.05
Copyright ANPEC Electronics Corp. Rev. Rev.A.1 May., 2002
www.anpec.com.tw
APW7047
Cover Tape Dimensions
Application SOP- Carrier Width Cover Tape Width 21.3
Customer Service
Anpec Electronics Corp. Head Office Li-Hsin Road, SBIP, Hsin-Chu, Taiwan, R.O.C. 886-3-5642000 886-3-5642050 Taipei Branch 137, Lane 235, Chiao Rd., Hsin Tien City, Taipei Hsien, Taiwan, 886-2-89191368 886-2-89191369
Copyright ANPEC Electronics Corp. Rev. Rev.A.1 May., 2002
www.anpec.com.tw
Other recent searches
WFB40G0897CD - WFB40G0897CD WFB40G0897CD Datasheet
V802 - V802 V802 Datasheet
MA2901 - MA2901 MA2901 Datasheet
FJC1308 - FJC1308 FJC1308 Datasheet
FJC1963 - FJC1963 FJC1963 Datasheet
DCR3220A65 - DCR3220A65 DCR3220A65 Datasheet
COP87L88EK - COP87L88EK COP87L88EK Datasheet
COP87L84EK - COP87L84EK COP87L84EK Datasheet
2SC5440 - 2SC5440 2SC5440 Datasheet
2SC4559 - 2SC4559 2SC4559 Datasheet
Privacy Policy | Disclaimer
© 2012 Datasheet Archive
