SD-B2920 Series PRELIMINARY Description SD-B2920 Series quar
|
|
|
Top Searches for this datasheet
Data Sheet 0134A Rev.
SD-B2920 Series
PRELIMINARY Description
SD-B2920 Series quartz crystal oscillators provide DPECL Fast Edge compatible signals. Systems designers specify space-saving, cost-effective packaged PECL oscillators meet their timing requirements.
Features
Wide frequency range- 106.250 125.0MHz (Consult factory complete frequency range) User specified tolerance available Will withstand vapor phase temperatures 253°C minutes maximum Space-saving alternative discrete component oscillators High shock resistance, 1000g Metal electrically connected ground reduce Electrical Connection Connection Enable/Disable N.C. /Ground Output /Output volt operation Fast rise fall times <600 Jitter Overtone technology High Crystal actively tuned oscillator circuit Power supply decoupling internal internal avoids cascading problems High frequencies proprietary design Gold plated pads HALT tested oscillator start-up
Beloit Street, P.O. 457, Burlington, 53105-0457 U.S.A. Phone 262/763-3591 262/763-2881 Email: nelsales@nelfc.com www.nelfc.com
SD-B2920 Series Continued Differential Positive (DPECL) Fast Edge Operating Conditions Output Characteristics
Electrical Characteristics
Parameter Frequency(6) Duty Cycle Logic Logic 1(2) Rise Fall Time Jitter, RMS(3) Enable Voltage(5) Disable Voltage Frequency Stability Symbol Conditions -106.250MHz VCC-1.29V 45/55% -VCC-1.95V -VCC-1.02V tr,tf 20-80%VO with load VCC-2V -200 psec -with -0.4V -with dF/F Overall conditions including: -100ppm voltage, calibration, temp., aging, shock, vibration
Data Sheet 0134A Rev.
Typical
125.0MHz 55/45% VCC-1.60V VCC-0.74V psec +200 psec psec -0.4V +100ppm
General Characteristics
Parameter Supply Voltage Supply Current Output current Operating temperature Storage temperature Power Dissipation Lead temperature Load Start-up time Conditions -2.375V termination 2.00V below level Output Current -0°C -55°C Soldering, sec. VCC-2V Thevenin Equivalent, Bias Required Symbol Typical 2.5V 2.625V ±50.0 70°C 125°C 300°C
Environmental Mechanical Characteristics
Mechanical Shock Thermal Shock Vibration Soldering Condition Hermetic Seal MIL-STD-202, Method 213, Condition MIL-STD-833, Method 1011, Condition 0.060" double amplitude 35g's 55Hz 2000 300°C seconds Leak rate less than atm.cc/sec helium
Footnotes: Standard frequency stability (±20,±25,±50ppm others available) VOL, VOH, referenced ground (VEE) with 2.5V Jitter performance frequency dependent. Please contact factory full characterization. phse shift between falling edge 2.0V rising edge 2.01V. Open enable also enables output. Consult factory complete frequency range.
Creating Part Number B292X FREQ Package Code 5x7mm Tolerance/Performance ±100ppm 0-70°C ±50ppm 0-70°C ±25ppm 0-70°C Customer Specific ±20ppm 0-70°C ±50ppm +85°C ±100ppm +85°C
Input Voltage Code Specification 3.3V 2.5V
Beloit Street, P.O. 457, Burlington, 53105-0457 U.S.A. Phone 262/763-3591 262/763-2881 Email: nelsales@nelfc.com www.nelfc.com
Other recent searches
XC164KM - XC164KM XC164KM Datasheet
TDA7220 - TDA7220 TDA7220 Datasheet
TB0309A - TB0309A TB0309A Datasheet
RW-3006 - RW-3006 RW-3006 Datasheet
MBR10 - MBR10 MBR10 Datasheet
Privacy Policy | Disclaimer
© 2012 Datasheet Archive
