MC74HC175A identical pinout LS175. device inputs compatible with stand

The Datasheet Archive - 100 Million Datasheets from 7500 Manufacturers.

MC74HC175A identical pinout LS175. device inputs compatible with stand

Datasheet Thumbnail

Top Searches for this datasheet

MC74HC175A Quad Flip-Flop with Common Clock Reset
MC74HC175A identical pinout LS175. device inputs compatible with standard CMOS outputs; with pullup resistors, they compatible with LSTTL outputs. This device consists four flip-flops with common Reset Clock inputs, separate inputs. Reset (active-low) asynchronous occurs when level applied Reset input. Information input transferred corresponding output next positive going edge Clock input.
PDIP-16 SUFFIX CASE
MC74HC175AN AWLYYWW
Output Drive Capability: LSTTL Loads Outputs Directly Interface CMOS, NMOS, Operating Voltage Range: Input Current: High Noise Immunity Characteristic CMOS Devices Compliance with Requirements Defined JEDEC Standard Chip Complexity FETs 41.5 Equivalent Gates
LOGIC DIAGRAM
CLOCK
SO-16 SUFFIX CASE 751B
HC175A AWLYWW
TSSOP-16 SUFFIX CASE 948F Assembly Location Wafer Year Work Week 175A ALYW
DATA INPUTS
RESET
INVERTING NONINVERTING OUTPUTS
ASSIGNMENT
RESET CLOCK
FUNCTION TABLE
Inputs Reset Clock Outputs Change
ORDERING INFORMATION
Device MC74HC175AN MC74HC175AD MC74HC175ADR2 MC74HC175ADT MC74HC175ADTR2 Package PDIP-16 SOIC-16 SOIC-16 TSSOP-16 TSSOP-16 Shipping 2000 Rail 2500 Reel Rail 2500 Reel
Semiconductor Components Industries, LLC, 1999
March, 2000 Rev.
Publication Order Number: MC74HC175A/D
MC74HC175A
MAXIMUM RATINGS*
Symbol Parameter Value Unit Supply Voltage (Referenced GND) Input Voltage (Referenced GND) Vout Output Voltage (Referenced GND) Input Current, Iout Output Current, Supply Current, Pins Power Dissipation Still Air, Plastic SOIC Package TSSOP Package Tstg Storage Temperature
This device contains protection circuitry guard against damage high static voltages electric fields. However, precautions must taken avoid applications voltage higher than maximum rated voltages this high-impedance circuit. proper operation, Vout should constrained range (Vin Vout) VCC. Unused inputs must always tied appropriate logic voltage level (e.g., either VCC). Unused outputs must left open.
Lead Temperature, from Case Seconds (Plastic DIP, SOIC TSSOP Package)
*Maximum Ratings those values beyond which damage device occur. Functional operation should restricted Recommended Operating Conditions. Derating Plastic DIP: mW/_C from 125_C SOIC Package: mW/_C from 125_C TSSOP Package: mW/_C from 125_C high frequency heavy load considerations, Chapter Motorola High-Speed CMOS Data Book (DL129/D).
RECOMMENDED OPERATING CONDITIONS
Symbol Parameter Unit
Supply Voltage (Referenced GND)
Vin, Vout
Input Voltage, Output Voltage (Referenced GND) Operating Temperature, Package Types Input Rise Fall Time (Figure
1000
ELECTRICAL CHARACTERISTICS (Voltages Referenced GND)
Guaranteed Limit
Symbol
Parameter
Test Conditions
25_C 3.15 1.35 1.80
85_C 125_C
3.15 1.35 1.80 3.15 1.35 1.80
Unit
Minimum High-Level Input Voltage
Vout |Iout|
Maximum Low-Level Input Voltage
Vout |Iout|
Minimum High-Level Output Voltage
|Iout|
|Iout| |Iout| |Iout|
2.48 3.98 5.48
2.34 3.84 5.34
2.20 3.70 5.20
http://onsemi.com
MC74HC175A
ELECTRICAL CHARACTERISTICS (Voltages Referenced GND)
Guaranteed Limit Symbol Parameter Test Conditions 25_C
85_C 125_C
0.33 0.33 0.33 0.40 0.40 0.40
Unit
Maximum Low-Level Output Voltage
|Iout|
|Iout| |Iout| |Iout| Iout
0.26 0.26 0.26
Maximum Input Leakage Current
Maximum Quiescent Supply Current (per Package)
NOTE: Information typical parametric values found Chapter Motorola High-Speed CMOS Data Book (DL129/D).
ELECTRICAL CHARACTERISTICS Input
Guaranteed Limit
Symbol fmax
Parameter
25_C
85_C 125_C
Unit
Maximum Clock Frequency (50% Duty Cycle) (Figures
tPLH, tPHL
Maximum Propagation Delay, Clock (Figures
tPHL
Maximum Propagation Delay, Reset (Figures
tTLH, tTHL
Maximum Output Transition Time, Output (Figures
Maximum Input Capacitance
NOTES: propagation delays with loads other than Chapter Motorola High-Speed CMOS Data Book (DL129/D). Information typical parametric values found Chapter Motorola High-Speed CMOS Data Book (DL129/D). Typical 25°C, Power Dissipation Capacitance (Per Flip-Flop)*
Used determine no-load dynamic power consumption: load considerations, Chapter Motorola High-Speed CMOS Data Book (DL129/D).
http://onsemi.com
NOTE: Information typical parametric values found Chapter Motorola High-Speed CMOS Data Book (DL129/D).
TIMING REQUIREMENTS (Input
Symbol
trec
Maximum Input Rise Fall Times (Figure
Minimum Pulse Width, Reset (Figure
Minimum Pulse Width, Clock (Figure
Minimum Recovery Time, Reset Inactive Clock (Figure
Minimum Hold Time, Clock Data (Figure
Minimum Setup Time, Data Clock (Figure
Parameter
http://onsemi.com
MC74HC175A
25_C 1000 Guaranteed Limit
85_C 125_C
1000
1000
Unit
MC74HC175A
SWITCHING WAVEFORMS
RESET CLOCK 1/fmax tPLH tPHL CLOCK tTLH tTHL tPHL tPLH trec
Figure
Figure
VALID DATA CLOCK
Figure
TEST CIRCUIT
TEST POINT OUTPUT DEVICE UNDER TEST
*Includes probe capacitance
Figure
http://onsemi.com
MC74HC175A
EXPANDED LOGIC DIAGRAM
CLOCK
RESET
http://onsemi.com
MC74HC175A
PACKAGE DIMENSIONS
PDIP-16 SUFFIX CASE 648-08 ISSUE
NOTES: DIMENSIONING TOLERANCING ANSI Y14.5M, 1982. CONTROLLING DIMENSION: INCH. DIMENSION CENTER LEADS WHEN FORMED PARALLEL. DIMENSION DOES INCLUDE MOLD FLASH. ROUNDED CORNERS OPTIONAL. INCHES MILLIMETERS 0.740 0.770 18.80 19.55 0.250 0.270 6.85 6.35 0.145 0.175 4.44 3.69 0.015 0.021 0.53 0.39 0.040 0.070 1.77 1.02 0.100 2.54 0.050 1.27 0.008 0.015 0.38 0.21 0.110 0.130 3.30 2.80 0.295 0.305 7.74 7.50 0.020 0.040 1.01 0.51
0.25 (0.010)
SEATING PLANE
SOIC-16 SUFFIX CASE 751B-05 ISSUE
NOTES: DIMENSIONING TOLERANCING ANSI Y14.5M, 1982. CONTROLLING DIMENSION: MILLIMETER. DIMENSIONS INCLUDE MOLD PROTRUSION. MAXIMUM MOLD PROTRUSION 0.15 (0.006) SIDE. DIMENSION DOES INCLUDE DAMBAR PROTRUSION. ALLOWABLE DAMBAR PROTRUSION SHALL 0.127 (0.005) TOTAL EXCESS DIMENSION MAXIMUM MATERIAL CONDITION. MILLIMETERS 9.80 10.00 4.00 3.80 1.75 1.35 0.49 0.35 1.25 0.40 1.27 0.25 0.19 0.25 0.10 6.20 5.80 0.50 0.25 INCHES 0.386 0.393 0.150 0.157 0.054 0.068 0.014 0.019 0.016 0.049 0.050 0.008 0.009 0.004 0.009 0.229 0.244 0.010 0.019
0.25 (0.010)
SEATING
PLANE
0.25 (0.010)
http://onsemi.com
MC74HC175A
PACKAGE DIMENSIONS
TSSOP-16 SUFFIX CASE 948F-01 ISSUE
0.10 (0.004) 0.15 (0.006)
IDENT.
SECTION
0.25 (0.010) 0.15 (0.006)
DETAIL
NOTES: DIMENSIONING TOLERANCING ANSI Y14.5M, 1982. CONTROLLING DIMENSION: MILLIMETER. DIMENSION DOES INCLUDE MOLD FLASH. PROTRUSIONS GATE BURRS. MOLD FLASH GATE BURRS SHALL EXCEED 0.15 (0.006) SIDE. DIMENSION DOES INCLUDE INTERLEAD FLASH PROTRUSION. INTERLEAD FLASH PROTRUSION SHALL EXCEED 0.25 (0.010) SIDE. DIMENSION DOES INCLUDE DAMBAR PROTRUSION. ALLOWABLE DAMBAR PROTRUSION SHALL 0.08 (0.003) TOTAL EXCESS DIMENSION MAXIMUM MATERIAL CONDITION. TERMINAL NUMBERS SHOWN REFERENCE ONLY. DIMENSION DETERMINED DATUM PLANE -W-. MILLIMETERS 4.90 5.10 4.30 4.50 1.20 0.05 0.15 0.50 0.75 0.65 0.18 0.28 0.09 0.20 0.09 0.16 0.19 0.30 0.19 0.25 6.40 INCHES 0.193 0.200 0.169 0.177 0.047 0.002 0.006 0.020 0.030 0.026 0.007 0.011 0.004 0.008 0.004 0.006 0.007 0.012 0.007 0.010 0.252
0.10 (0.004) SEATING
PLANE
DETAIL
Semiconductor trademarks Semiconductor Components Industries, (SCILLC). SCILLC reserves right make changes without further notice products herein. SCILLC makes warranty, representation guarantee regarding suitability products particular purpose, does SCILLC assume liability arising application product circuit, specifically disclaims liability, including without limitation special, consequential incidental damages. "Typical" parameters which provided SCILLC data sheets and/or specifications vary different applications actual performance vary over time. operating parameters, including "Typicals" must validated each customer application customer's technical experts. SCILLC does convey license under patent rights rights others. SCILLC products designed, intended, authorized components systems intended surgical implant into body, other applications intended support sustain life, other application which failure SCILLC product could create situation where personal injury death occur. Should Buyer purchase SCILLC products such unintended unauthorized application, Buyer shall indemnify hold SCILLC officers, employees, subsidiaries, affiliates, distributors harmless against claims, costs, damages, expenses, reasonable attorney fees arising directly indirectly, claim personal injury death associated with such unintended unauthorized use, even such claim alleges that SCILLC negligent regarding design manufacture part. SCILLC Equal Opportunity/Affirmative Action Employer.
PUBLICATION ORDERING INFORMATION
NORTH AMERICA Literature Fulfillment: Literature Distribution Center Semiconductor P.O. 5163, Denver, Colorado 80217 Phone: 303-675-2175 800-344-3860 Toll Free USA/Canada Fax: 303-675-2176 800-344-3867 Toll Free USA/Canada Email: ONlit@hibbertco.com Response Line: 303-675-2167 800-344-3810 Toll Free USA/Canada American Technical Support: 800-282-9855 Toll Free USA/Canada EUROPE: Semiconductor European Support German Phone: (+1) 303-308-7140 (M-F 1:00pm 5:00pm Munich Time) Email: ONlit-german@hibbertco.com French Phone: (+1) 303-308-7141 (M-F 1:00pm 5:00pm Toulouse Time) Email: ONlit-french@hibbertco.com English Phone: (+1) 303-308-7142 (M-F 12:00pm 5:00pm Time) Email: ONlit@hibbertco.com EUROPEAN TOLL-FREE ACCESS*: 00-800-4422-3781 *Available from Germany, France, Italy, England, Ireland CENTRAL/SOUTH AMERICA: Spanish Phone: 303-308-7143 (Mon-Fri 8:00am 5:00pm MST) Email: ONlit-spanish@hibbertco.com ASIA/PACIFIC: Semiconductor Asia Support Phone: 303-675-2121 (Tue-Fri 9:00am 1:00pm, Hong Kong Time) Toll Free from Hong Kong Singapore: 001-800-4422-3781 Email: ONlit-asia@hibbertco.com JAPAN: Semiconductor, Japan Customer Focus Center 4-32-1 Nishi-Gotanda, Shinagawa-ku, Tokyo, Japan 141-8549 Phone: 81-3-5740-2745 Email: r14525@onsemi.com Semiconductor Website: http://onsemi.com
additional information, please contact your local Sales Representative.
http://onsemi.com
MC74HC175A/D

MC74HC175A identical pinout LS175. device inputs compatible with stand

Top Searches for this datasheet

Other recent searches