Revision 1.0, January 2005 Part Number 82-000845-01 Copyright Inf
|
|
|
Top Searches for this datasheet
Blackfin USB-LAN EZ-Extender Manual
Revision 1.0, January 2005 Part Number 82-000845-01
Copyright Information
2005 Analog Devices, Inc., RIGHTS RESERVED. This document reproduced form without prior, express written consent from Analog Devices, Inc. Printed USA.
Limited Warranty
USB-LAN EZ-Extender warranted against defects materials workmanship period year from date purchase from Analog Devices from authorized dealer.
Disclaimer
Analog Devices, Inc. reserves right change this product without prior notice. Information furnished Analog Devices believed accurate reliable. However, responsibility assumed Analog Devices use; infringement patents other rights third parties which result from use. license granted implication otherwise under patent rights Analog Devices, Inc.
Trademark Service Mark Notice
Analog Devices logo, Blackfin, VisualDSP++, EZ-KIT Lite registered trademarks Analog Devices, Inc. other brand product names trademarks service marks their respective owners.
Regulatory Compliance
Blackfin USB-LAN EZ-Extender been certified comply with essential requirements European directive 89/336/EEC (inclusive 93/68/EEC) and, therefore, carries "CE" mark. Blackfin USB-LAN EZ-Extender been appended Analog Devices Development Tools Technical Construction File referenced "DSPTOOLS1" dated December 1997 awarded Certification appointed European Competent Body file.
EZ-KIT Lite evaluation system contains (electrostatic discharge) sensitive devices. Electrostatic charges readily accumulate human body equipment discharge without detection. Permanent damage occur devices subjected high-energy discharges. Proper precautions recommended avoid performance degradation loss functionality. Store unused EZ-KIT Lite boards protective shipping package.
CONTENTS
PREFACE
Product Overview viii Purpose This Manual Intended Audience Manual Contents What's This Manual Technical Customer Support Supported Products Product Information Related Documents Notation Conventions
USB-LAN EZ-EXTENDER INTERFACES
USB-LAN EZ-Extender Setup Software Ethernet Software Interface Ethernet Interface Optional ADSP-BF537 EZ-KIT Lite Interfaces
Blackfin USB-LAN EZ-Extender Manual
CONTENTS
Power-Over-Ethernet Interface
USB-LAN EZ-EXTENDER HARDWARE REFERENCE
System Architecture Jumper Setting Power Select Jumper (JP1) Power Jumper (JP2) Link Jumper (JP3) Switch Settings ADDR Enable Switch (SW1.1) FLAGS Enable Switch (SW1.2) Enable Switch (SW1.3) Test Mode Enable Switch (SW1.4) Serial Enable Switch (SW2.1) IOS[2:0] Switch (SW2.2, SW2.3, SW2.4)
BILL MATERIALS INDEX
Blackfin USB-LAN EZ-Extender Manual
PREFACE
Thank purchasing Blackfin® USB-LAN EZ-Extender, Analog Devices, Inc. extension board EZ-KIT Lite® evaluation system ADSP-BF533, ADSP-BF537, ADSP-BF561 Blackfin processors. Blackfin processors embedded processors that support Media Instruction Computing (MISC) architecture. This architecture natural merging RISC, media functions, digital signal processing characteristics towards delivering signal processing performance microprocessor-like environment. EZ-KIT Lite USB-LAN EZ-Extender designed used conjunction with VisualDSP++® development environment. VisualDSP++ offers powerful programming tool with flexibility that significantly decreases time required port software code processor, reducing time-to-market. learn more about Analog Devices development software,
Blackfin USB-LAN EZ-Extender Manual
Product Overview
Product Overview
Blackfin USB-LAN EZ-Extender separately sold extension board that plugs onto expansion interface ADSP-BF533, ADSP-BF537, ADSP-BF561 EZ-KIT Lite evaluation system. extension board aids design prototyping phases ADSP-BF533, ADSP-BF537, ADSP-BF561 processor targeted applications. board extends capabilities evaluation system providing connection between Asynchronous Memory Blackfin processor (Asynchronous Memory Bank either 10/100 Mbps Ethernet device. following list Blackfin USB-LAN EZ-Extender interfaces. Interface PLX's Technology Netchip 2272 device Driver Application code Logo Certified Ethernet Interface SMSC's 91C111 device supported ADSP-BF533 EZ-KIT ADSP-BF561 EZ-KIT Lites IEEE802.3.AF Compliant Power-Over-Ethernet application ADSP-BF537 EZ-KIT Lite SMSC's Connector evaluate different PHYs with ADSP-BF537 EZ-KIT Lite Ethernet Stack Application code Power Supply Required Derives Power from EZ-KIT Lite Certified
viii
Blackfin USB-LAN EZ-Extender Manual
Preface
Dimensions 3.13 Before using interfaces, follow setup procedure "USB-LAN EZ-Extender Setup" page 1-1. Example programs available demonstrate capabilities Blackfin USB-LAN EZ-Extender board.
Purpose This Manual
Blackfin USB-LAN EZ-Extender Manual describes operation configuration components extension board. schematic bill materials provided reference future Blackfin processor board designs.
Intended Audience
This manual user's guide reference Blackfin USB-LAN EZ-Extender. Programmers familiar with Analog Devices Blackfin processor architecture, operation, development tools primary audience this manual. Programmers unfamiliar with VisualDSP++ EZ-KIT Lite evaluation software should refer ADSP-BF533, ADSP-BF537, ADSP-BF561 Evaluation System Manual, VisualDSP++ online Help, user's getting started guides. locations these documents, refer "Related Documents".
Blackfin USB-LAN EZ-Extender Manual
Manual Contents
Manual Contents
manual consists Chapter "USB-LAN EZ-Extender Interfaces" page Provides basic board information. Chapter "USB-LAN EZ-Extender Hardware Reference" page Provides information hardware aspects board. Appendix "Bill Materials" page Provides list components used manufacture EZ-Extender board. Appendix "Schematics" page Provides resources allow EZ-KIT Lite board-level debugging reference design. This appendix part online Help. online Help viewers should version Blackfin USB-LAN EZ-Extender Manual located Docs\EZ-KIT Lite Manuals folder installation schematics. Alternatively, schematics found Analog Devices site, www.analog.com/processors.
What's This Manual
This first edition Blackfin USB-LAN EZ-Extender Manual.
Blackfin USB-LAN EZ-Extender Manual
Preface
Technical Customer Support
reach processor Tools Support following ways. Visit Embedded Processing processor products site
E-mail tools questions
dsptools.support@analog.com
E-mail processor questions
dsp.support@analog.com
Phone questions 1-800-ANALOGD Contact your Analog Devices, Inc. local sales office authorized distributor Send questions mail
Analog Devices, Inc. Technology P.O. 9106 Norwood, 02062-9106
Supported Products
Blackfin USB-LAN EZ-Extender designed extension board ADSP-BF533, ADSP-BF537, ADSP-BF561 EZ-KIT Lite evaluation systems.
Blackfin USB-LAN EZ-Extender Manual
Product Information
Product Information
obtain product information from Analog Devices site, from product CD-ROM, from printed publications (manuals). Analog Devices online www.analog.com. site provides information about broad range products-analog integrated circuits, amplifiers, converters, digital signal processors.
Related Documents
information product related development software, following publications. Table Related Processor Publications
Title ADSP-BF533 Embedded Processor Datasheet ADSP-BF536/ADSP-BF537 Embedded Processor Datasheet ASP-BF561 Blackfin Embedded Symmetric Multi-Processor Datasheet Description General functional description, pinout, timing.
ADSP-BF533 Blackfin Processor Hard- Description internal processor architecture ware Reference register functions ADSP-BF537 Blackfin Processor Hardware Reference ASP-BF561 Blackfin Processor Hardware Reference Description allowed processor assembly instructions.
Blackfin Processor Instruction Reference
Blackfin USB-LAN EZ-Extender Manual
Preface
Table Related VisualDSP++ Publications
Title ADSP-BF533 EZ-KIT Lite Evaluation System Manual ADSP-BF537 EZ-KIT Lite Evaluation System Manual ADSP-BF561 EZ-KIT Lite Evaluation System Manual Description Description EZ-KIT Lite features usage. Note: ADSP-BF537 EZ-KIT Lite, there additional Getting Started with ADSP-BF537 EZ-KIT Lite. Description VisualDSP++ features usage Description assembler function commands Description complier function commands Blackfin processors Description linker function commands Description loader function commands
VisualDSP++ User's Guide VisualDSP++ Assembler Preprocessor Manual VisualDSP++ C/C++ Complier Library Manual Blackfin Processors VisualDSP++ Linker Utilities Manual VisualDSP++ Loader Manual
documentation available online. Most documentation available printed form. Visit Technical Library site access processor tools manuals data sheets:
Blackfin USB-LAN EZ-Extender Manual
xiii
Notation Conventions
Notation Conventions
Text conventions used this manual identified described follows.
Example Close command (File menu)
{this that}
Description Titles reference sections indicate location item within VisualDSP++ environment's menu system (for example, Close command appears File menu). Alternative required items syntax descriptions appear within curly brackets separated vertical bars; read example this that. other required. Optional items syntax descriptions appear within brackets separated vertical bars; read example optional this that. Optional item lists syntax descriptions appear within brackets delimited commas terminated with ellipse; read example optional comma-separated list this. Commands, directives, keywords, feature names text with letter gothic font. Non-keyword placeholders appear text with italic style format. Note: correct operation, Note provides supplementary information related topic. online version this book, word Note appears instead this symbol. Caution: Incorrect device operation result Caution: Device damage result Caution identifies conditions inappropriate usage product that could lead undesirable results product damage. online version this book, word Caution appears instead this symbol. Warning: Injury device users result Warning identifies conditions inappropriate usage product that could lead conditions that potentially hazardous devices users. online version this book, word Warning appears instead this symbol.
[this that]
[this,.]
.SECTION
filename
Blackfin USB-LAN EZ-Extender Manual
Preface
Additional conventions, which apply only specific chapters, appear throughout this document.
Blackfin USB-LAN EZ-Extender Manual
Notation Conventions
Blackfin USB-LAN EZ-Extender Manual
USB-LAN EZ-EXTENDER INTERFACES
After following setup procedures both Blackfin USB-LAN EZ-Extender EZ-KIT Lite (ADSP-BF533, ADSP-BF537 ADSP-BF561), chapter describes each interfaces extender supports. information presented following order. "USB Interface" page "Ethernet Interface" page "Optional ADSP-BF537 EZ-KIT Lite Interfaces" page
USB-LAN EZ-Extender Setup
very important components system containing USB-LAN EZ-Extender before applying power that system. following procedure recommended correct setup. Power your system when these steps completed: Read applicable design interface section this chapter-the text provides overview capabilities interface. Read "System Architecture" page understand physical connections extension board. detailed information, refer "Schematics page B-1".
Blackfin USB-LAN EZ-Extender
USB-LAN EZ-Extender Setup
Remove rubber feet that attached EZ-KIT Lite. place these rubber feet, install nylon feet screws provided with USB-LAN EZ-Extender. Install nylon feet mounting holes EZ-KIT Lite's PCB. Flip EZ-KIT Lite upside down that three expansion headers (J1-3) facing switches jumpers USB-LAN EZ-Extender board. block diagram Figure page conjunction with "Jumper Setting" page "Switch Settings" page 2-6. switches jumpers EZ-KIT Lite board. already, familiarize yourself with documentation schematics EZ-KIT Lite (see "Related Documents"). Compare expansion interface signals USB-LAN EZ-Extender board with signals EZ-KIT Lite board ensure there contention. example, necessary disable other devices connected expansion interface processor disable push buttons EZ-KIT Lite. Install USB-LAN EZ-Extender EZ-KIT Lite three-connector expansion interface. Configure other interfacing boards, example, another EZ-Extender board.
Software
information software (host-side device-side), refer Software Readme.txt file located .\VisualDSP++ install path\Blackfin\EZ-KITs\USB-LAN EZ-EXTENDER\usb directory.
Blackfin USB-LAN EZ-Extender
USB-LAN EZ-Extender Interfaces
Ethernet Software
Readme.txt
information software, refer Software file located .\VisualDSP++ install path\Blackfin\EZ-KITs\USB-LAN EZ-EXTENDER\lan directory.
Interface
USB-LAN EZ-Extender allows connect chip Blackfin processor without other programmable logic required. PLX's (formerly Netchip) Net2272 device ties directly Asynchronous Memory Bank Blackfin processor. read from write controller directly addressing named memory bank. reset Net2272 processor asserting these flag pins: PF11 ADSP-BF533 processor, ADSP-BF537 processor, PF11 ADSP-BF561 processor. flag pins used push buttons LEDs respective EZ-KIT Lite; consequently, user must make proper changes that EZ-KIT Lite. switch settings required each respective EZ-KIT Lites described Software Readme.txt file .\Blackfin\EZ-KITs\USB-LAN EZ-EXTENDER\usb subdirectory VisualDSP++ installation directory. readme file describes software, source code, drivers, explains USB-based application. correct switch settings, refer schematics drawing respective device. line extender connects PF10 ADSP-BF533, ADSP-BF537, PF10 ADSP-BF561 processors. These flag pins used push buttons LEDs respective EZ-KIT Lites; consequently, user must make proper changes that EZ-KIT Lite.
Blackfin USB-LAN EZ-Extender
Ethernet Interface
When writing reading from device using EZ-KIT Lites, memory addresses from Table 1-1. Table 1-1. Device Memory
EZ-KIT Connects ADSP-BF533 EZ-KIT Lite ADSP-BF537 EZ-KIT Lite ADSP-BF561 EZ-KIT Lite Starting Address
0x2030 0000 0x2030 0000 0x2C00 0000
Ending Address
0x2030 007F 0x2030 007F 0x2C00 007F
Ethernet Interface
USB-LAN EZ-Extender allows connect 10/100 Mbps Ethernet chip Blackfin processor. SMSC's LAN91C111 device ties directly Asynchronous Memory Bank Blackfin processor. read from write Ethernet controller directly addressing named memory bank. reset Ethernet processor asserting board reset ADSP-BF533 ADSP-BF561 EZ-KIT Lites. reset connects supervisory reset circuit managed Analog Devices ADM708 device. ADM708 also asserts reset Ethernet chip power-up. Ethernet line connects flag ADSP-BF533 processor ADSP-BF561 processor. flag pins used push buttons LEDs respective EZ-KIT Lite; consequently, user must remember make proper changes that EZ-KIT Lite. switch settings required each respective EZ-KIT Lites described Software Readme.txt file .\Blackfin\EZ-KITs\USB-LAN EZ-EXTENDER\lan subdirectory Visu-
Blackfin USB-LAN EZ-Extender
USB-LAN EZ-Extender Interfaces
alDSP++ installation directory. readme file describes software, source code, drivers, explains Ethernet application. correct switch settings, refer schematics drawing respective device. When writing reading from Ethernet device using EZ-KIT Lites, memory ranges from Table 1-2. Table 1-2. Device Memory
EZ-KIT Connects ADSP-BF533 EZ-KIT Lite ADSP-BF561 EZ-KIT Lite Starting Address
0x2031 0000 0x2C01 0000
Ending Address
0x2031 FFFF 0x2C01 FFFF
Optional ADSP-BF537 EZ-KIT Lite Interfaces
Optional ADSP-BF537 EZ-KIT Lite interfaces are: "Power-Over-Ethernet" "MII Interface"
Power-Over-Ethernet
Blackfin USB-LAN EZ-Extender, when used conjunction with ADSP-BF537 EZ-KIT Lite, allows user power both EZ-KIT Lite extender 10/100 Mbps switch Midspan device that supports IEEE802.3.AF.
Blackfin USB-LAN EZ-Extender
Optional ADSP-BF537 EZ-KIT Lite Interfaces
EZ-KIT Lite extender must powered 7.5V supply when Power-over-Ethernet mode. user make appropriate jumper changes EZ-KIT Lite extender then connect extender power both boards switch Midspan device. user must switch Midspan device that supports power data pairs. user uses Midspan device that powers only over spare pins, then circuitry will work. Table shows recommended Midspan device that supports both power over spare pins power over data pairs. Table 1-3. Midspan Device
Power Sourcing Equipment Midspan Device Manufacturer PowerDsine Part Number PD-8006/AC
Ethernet connector EZ-KIT Lite application. Power-over-Ethernet will work properly Ethernet connector used extender board. When mode, blinking LEDs (LED[1:6]) confirm successful power-up. Since intended simple demonstration power circuitry, able bring VisualDSP session while Power-over-Ethernet mode. Refer "Power Select Jumper (JP1)" page extender's settings. Refer ADSP-BF537 EZ-KIT Lite Evaluation System Manual EZ-KIT Lite's settings.
Interface
Media Independent Interface (MII) allows evaluate different devices with ADSP-BF537 EZ-KIT Lite. separately purchased evaluation board connects directly USB-LAN EZ-Extender. also need purchase connector solder able connect boards together. part numbers SMSC's evaluation boards connector shown Table 1-4.
Blackfin USB-LAN EZ-Extender
USB-LAN EZ-Extender Interfaces
Table 1-4. Devices
Part Description
Manufacturer AMP/TYCO ELECTRONICS SMSC SMSC
Manufacturer Part 787170-4 EVB185 EVB183
20x2 Connector
Evaluation Board Evaluation Board
Blackfin USB-LAN EZ-Extender
Optional ADSP-BF537 EZ-KIT Lite Interfaces
Blackfin USB-LAN EZ-Extender
USB-LAN EZ-EXTENDER HARDWARE REFERENCE
This chapter describes hardware design USB-LAN EZ-Extender. following topics covered. "System Architecture" page Describes configuration extension board explains board components interface with processor EZ-KIT Lite. "Jumper Setting" page Describes function configuration jumpers, JP1-3. "Switch Settings" page Describes function switches, SW1.1-1.3.
Blackfin USB-LAN EZ-Extender Manual
System Architecture
System Architecture
block diagram Blackfin USB-LAN EZ-Extender shown Figure 2-1.
Ethernet Connector
SMSC Connector (BF537 Only)
Buffer Driver
3.3V
ADDR[15:1] DATA[31:0] CNTRL
SMSC LAN91C111 (Ethernet)
3.3V
Da[15:0] ADDR[15:1]
Expansion Interface from BlackFIN EZ-KIT Lites
DATA[31:0]
16bit Db[15:0]
3.3V
ADDR[5:1] DATA[15:0] CNTRL
Netchip NET2272 (USB 2.0)
3.3V 2.5V
CNTRL
5.0V Regulation Circuitry
3.3V 3.3V 2.5V
16bit Da[31:16]
3.3V
Conn
Power Over Ethernet Ciruitry
Figure 2-1. Block Diagram
Blackfin USB-LAN EZ-Extender Manual
USB-LAN EZ-Extender Hardware Reference
Jumper Setting
Before using Blackfin USB-LAN EZ-Extender, follow steps "USB-LAN EZ-Extender Setup" page 1-1. Figure shows locations jumper headers. two-pin jumper placed respective jumper header different functionality. following sections describe possible jumper settings associated functionality.
Figure 2-2. Jumper Locations
Power Select Jumper (JP1)
power select jumper, JP1, default, must have jumpers pins. Jumpers used only when extender plugged into ADSP-BF537 EZ-KIT Lite.
Blackfin USB-LAN EZ-Extender Manual
Jumper Setting
Table 2-1. Settings
Source Power EZ-KIT Lite Power Test Mode Use) Power-over-Ethernet Setting Jumpers (Default)
JP1.1 JP1.2
JP1.2 JP1.3
When using ADSP-BF533 ADSP-BF561 EZ-KIT Lite, user must place jumpers JP1. Placing jumper damage extender card and/or EZ-KIT Lite. user must power ADSP-BF533/ADSP-BF561 EZ-KIT Lite USB-LAN EZ-Extender with 7.5V power supply provided with EZ-KIT Lite. When using ADSP-BF537 EZ-KIT Lite without Power-over-Ethernet feature, user must place jumpers JP1. user must power both EZ-KIT Lite extender with 7.5V power supply provided with EZ-KIT Lite. When using ADSP-BF537 EZ-KIT Lite with Power-over-Ethernet, user must place jumper between user must power both EZ-KIT Lite USB-LAN EZ-Extender with CAT5E Ethernet cable, which provides power over signal pairs. Ethernet cable must plugged into Ethernet connector ADSP-BF537 EZ-KIT Lite, USB-LAN EZ-Extender. 7.5V power supply provided with EZ-KIT Lite should used. overview Power-over-Ethernet interface, refer "Power-Over-Ethernet" page 1-5.
Blackfin USB-LAN EZ-Extender Manual
USB-LAN EZ-Extender Hardware Reference
Power Jumper (JP2)
power jumper, JP2, used power SMSC's 91C111 device with 3.3V. default, and, general, jumper plugged This jumper provided user flexibility. user must make changes jumper only when power applied USB-LAN EZ-Extender and/or EZ-KIT Lite. Table 2-2. Settings
Functionality Power LAN91C111 Other Cases Setting Jumper JP2.1 JP2.2 (Default)
Link Jumper (JP3)
link jumper, JP3, USB-LAN EZ-Extender directly connects Link Status SMSC's 91C111 device. default setting keep link jumper unpopulated. When jumper populated, sends logic input port used convey LINK status (EPHSR bit14). more information about populating jumper, refer SMSC LAN91C111 data sheet. Table 2-3. Settings
Functionality Logic 91C111 LINK Status Other Cases Setting
JP3.1
JP3.2
Jumper (Default)
Blackfin USB-LAN EZ-Extender Manual
Switch Settings
Switch Settings
Before using Blackfin USB-LAN EZ-Extender follow steps "USB-LAN EZ-Extender Setup" page 1-1. Figure shows locations switches. following sections describe possible switch settings associated functionality.
Figure 2-3. Switch Locations
ADDR Enable Switch (SW1.1)
address enable switch, SW1.1, used control output Blackfin address buffer. default, switch position. position, user cannot communicate
Blackfin USB-LAN EZ-Extender Manual
USB-LAN EZ-Extender Hardware Reference
Ethernet processor. address enable switch adds flexibility processors because turn switch when capacitive loading issue present with other peripherals EZ-KIT Lite. Table 2-4. SW1.1 Settings
Functionality Blackfin Address Buffer (U1) Enabled Blackfin Address Buffer (U1) Disabled SW1.1 Setting (Default)
FLAGS Enable Switch (SW1.2)
Flags enable switch, SW2.2, used control output Blackfin Flags multiplexer. default, SW1.2 switch position. position, user cannot communicate Ethernet processor. Flag enable switch adds flexibility extender-when switch OFF, Flags used other peripherals EZ-KIT Lite. Table 2-5. SW1.2 Settings
Functionality FLAGS (U12) Enabled Blackfin FLAGS (U12) Disabled SW1.2 Setting (Default)
Enable Switch (SW1.3)
enable switch, SW1.3, used control connection between Netchip 2272 line with respective Flag Blackfin processor. switch connects USB_IRQ line with PF10 ADSP-BF533 ADSP-BF561 processors, ADSP-BF537 processor. default, enable switch position. When position, communication with pro-
Blackfin USB-LAN EZ-Extender Manual
Switch Settings
cessor cannot established. SW1.3 adds flexibility extender- when switch OFF, Flag used other peripherals EZ-KIT Lite. Table 2-6. SW1.3 Settings
Functionality Enabled Disabled SW1.3 Setting (Default)
Test Mode Enable Switch (SW1.4)
test mode enable switch, SW1.4, internal test should used. This switch, default, position. Table 2-7. SW1.4 Settings
Functionality Test Mode Enabled Test Mode Disabled SW1.4 Setting (Default)
Serial Enable Switch (SW2.1)
Serial enable switch, SW2.1, used control connection between LAN91C111 Ethernet processor with serial (U3). When switch disabled, Ethernet processor loads address from serial ROM. SW2.1 switch, default, position. switch position, able communicate with Ethernet application code provided. switch adds flexibility extender-you modify application code generate another address when switch
Blackfin USB-LAN EZ-Extender Manual
USB-LAN EZ-Extender Hardware Reference
Table 2-8. SW2.1 Settings
Functionality Serial Disabled Serial Enabled SW2.1 Setting (Default)
IOS[2:0] Switch (SW2.2, SW2.3, SW2.4)
IOS[2:0] bits USB-LAN EZ-Extender directly connected IOS[2:0] pins LAN91C111 Ethernet processor. These switches, default, positions. pins used conjunction with Serial Enable switch select between predefined EEPROM configurations. more information about switches, refer SMSC LAN91C111 data sheet.
Blackfin USB-LAN EZ-Extender Manual
Switch Settings
2-10
Blackfin USB-LAN EZ-Extender Manual
BILL MATERIALS
bill materials corresponds board schematics page B-1. Please check latest schematics Analog Devices website,
Blackfin LAN-USB EZ-Extender Manual
Reference Designator SINU1 PERICOM SEMI MICROCHIP SEMI SMSC NETCHIP PERICOM SEMI PERICOM SEMI PERICOM SEMI ANALOG DEVICES ADP3330ART-2.5 ANALOG DEVICES ADP3330ART-3.3 Manufacturer Part Number EPSON AMERICA MA-505 25.000M-C2 SN74AHC1G00D PI74AVC+16244A 93LC46B/SN LAN91C111-NE NET2272 PI3B16234A PI3B16245A PI3B3257L
Ref.
Description
ADP3330ART-3.3 SOT23-6 3.3V-200MA REGULATOR
ADP3330ART-2.5 SOT23-6 2.5V-200MA REGULATOR
25MHZ OSC005 CRYSTAL
SN74AHC1G00 SOT23-5 GLE-2-INPUT-NAND
PI74AVC+16244 TSSOP48 2.5V 1.9NS 16BIT DRIVER
93LC46B SOIC8 Serial
LAN91C111 TQFP128 10/100 NON-PCI ETHERNET
NET2272 TQFP64 CONTROLLER
PI3B16234 TSSOP56 3.3V 16:32BUS
PI3B16245 TSSOP48 3.3V 16BIT SWITCH
Blackfin LAN-USB EZ-Extender Manual
PI3B3257 TSSOP16 3.3V MUXDEMUX
Ref. ECLIPTEK PULSE VISHAY SEMI LINEAR TECH MILL-MAX SAMTEC SWITCH HALO ELECTRONIC DALE PANASONIC C1,C3,C6,C8,C11,C13, C2,C7,C9-10,C12,C19-4 1,C43,C48 PA1134 PS2911-1-F3 SI3440DV-T1 TLV431ASN1T1 LTC4267CGN 897-30-004-90-00 TFC-145-32-F-D TDA04H0SK1 HFJ11-2450E CRCW1206-000J LN1461C-TR 08051C103KAT2 08055C104KAT EC2SM-30.000M PHILIPS LOGIC 74LVC139PW
Description
Reference Designator
Manufacturer
Part Number
74LVC139 TSSOP16 3.3V DUAL DECODER
P1-3 SW1-2 LED1-2
30MHZ CRYSTAL FUNDA- MENTAL FREQ
PA1134 TRANSFORMER
PS2911-1 PHOTOCOUPLER
SI3440DV TSOP6
TLV431A SOT23-3 VOLT SHUNT
Blackfin LAN-USB EZ-Extender Manual
LTC4267 SSOP16 CHIP SWITCH
4PIN
0.05 45x2
4PIN-SMT-SWT
RJ45 8PIN 10/100BASE-TX SHIELDED
0.00 1/8W 1206
AMBER-SMT GULL-WING
0.01uF 100V CERM
0.1uF CERM
Bill Materials
Reference Designator R1-4,R8-18,R36-45,R48, CT1-3 FER1-4,FER7 C14-15 R28-29,R46 FER5-6 R19,R21 C4-5,C44-45 C17-18,C42 VISHAY PANASONIC TAIYO YUDEN YAGEO DALE STEWARD VISHAY CR21-1004F-T CR21-1501F-T TAJB106K016R LL4148-13 HZ1206B601R CRCW12061102F 12061A300JAT2A CR21-4702F-T CRCW0805 0.0R ERJ-6ENF3321V FBMJ2125HS420-T 9C08052A39R0F 0805YC474KAT2 0805ZC105KAT2 TPSE687K006R0 CR21-4701F-T CR21-330JTR CR21-103J-T Manufacturer Part Number
Ref.
Description
100MW
100MW
4.7K 100MW
100MW
1.5K 100MW
10uF TANT
300MA LL4148 DL35 FAST SWITCHING DIOD
100MHZ 500MA 1206
11.0K 1/8W 1206
30pF 100V 1206
1/10W
0.00 100MW
3.32K 100MW
100MHZ
100MW
0.47UF
Blackfin LAN-USB EZ-Extender Manual
680uF 6.3V TANT-LOW-ESR
Ref. C46-47 R26-27,R30-31 R32-33 DIODES DIODES DIODES YAGEO YAGEO PANASONIC DALE JP2-3 PANASONIC BERG BERG YAGEO YAGEO YAGEO 08055A100JAT2A 9C08052A24R9F 9C08052A49R9F 9C08052A2431FK SMAJ58A-13 SBM1040-13 HD01-T 9C08052A68R1F 9C08052A6811FK ERJ-3RSFR12V CR1206-330JTR CRCW1206-1002 ECS-H1AX475R 54101-T08-02 54101-T08-03 VISHAY INTERTEC CRCW08051000F
Description
Reference Designator
Manufacturer
Part Number
1/10W
GREEN-YELLOW-SMT 1210
24.9 1/10W
49.9 1/10W
2.43K 1/10W
R22-23
SMAJ58A DIO003 TRANS VOLTAGE SUPPRESSOR
Blackfin LAN-USB EZ-Extender Manual
SBM1040 SCHOTTKY RECT
0.8A HD01 MDIP4 BRIDGE RECT
68.1 1/10W
6.81K 1/10W
0.12 1/10W 0603
1/8W 1206
10.0K 1/8W 1206
4.7uF TANT -55+125
IDC2X1
Bill Materials
IDC3X1
Blackfin LAN-USB EZ-Extender Manual
REVISIONS
DESCRIPTION
ENGR
DATE
06/14/04 08/27/04
APPR
BLACKFIN USB-LAN EZ-EXTENDER SCHEMATIC
Populate Manual Jumper Settings
ANALOG DEVICES
Approvals
Drawn Checked Engineering
Cotton Road Nashua, 03063 1-800-ANALOGD
Date
11/03/04
Title
BLACKFIN USB-LAN EZ-EXTENDER TITLE
Board
11-9-2004_11:39
Size
Date
A0187-2003
Sheet
REVISIONS
DESCRIPTION
ENGR
DATE
06/14/04 08/27/04
APPR
EXPANSION INTERFACE (TYPE
3.3V 3.3V
DSP_D[0:31] DSP_A[1:15] DSP_A2 DSP_A4 DSP_A6 DSP_A8 DSP_A10 DSP_A12 DSP_A14 DSP_A16 POE_VCC+ 561_PF12 561_PF10_537_PF7 DSP_D1 DSP_D3 DSP_D5 DSP_D7 DSP_D9 DSP_D11 DSP_D13 DSP_D15 DSP_D17 DSP_D19 DSP_D21 DSP_D23 DSP_D25 DSP_D27 DSP_D29 DSP_D31 AMS3 533_PF11 533_PF9 DSP_A1 DSP_A3 DSP_A5 DSP_A7 DSP_A9 DSP_A11 DSP_A13 DSP_A15 DSP_A17 45X2 CON018 ABE1 ABE0 561_ABE3 561_ABE2 533_PF10 3.3V CLK_OUT_EXP1 PHYINT RXD0 RXD2 RX_DV RX_ER TXD0 TXD2 TX_EN 45X2 CON018 0.1UF Decoupling 3.3V RXD1 RXD3 RX_CLK MDIO SN74AHC1G00 SOT23-5 RESET TXD1 TXD3 TX_CLK 537_DMAR
DSP_D0 DSP_D2 DSP_D4 DSP_D6 DSP_D8 DSP_D10 DSP_D12 DSP_D14 DSP_D16 DSP_D18 DSP_D20 DSP_D22 DSP_D24 DSP_D26 DSP_D28 DSP_D30 POE_VCC77 561_PF11_537_PF6 561_PF9_537_PF5 45X2 CON018
Populate Manual Jumper Settings
ANALOG DEVICES
Approvals
Drawn Checked Engineering
Cotton Road Nashua, 03063 1-800-ANALOGD
Date
11/03/04
Title
BLACKFIN USB-LAN EZ-EXTENDER EXPANSION INTERFACE
Board
11-17-2004_9:51
Size
Date
A0187-2003
Sheet
REVISIONS
LAN_D[0:31] LAN_D0 Decoupling Caps LAN_D1 3.3V LAN_D2 LAN_D3 Decoupling Caps LAN_D4 3.3V LAN_D5 LAN_D6 LAN_D7 LAN_D8 DSP_A3 LAN_D9 DSP_A4 LAN_D10 DSP_A5 LAN_D11 DSP_A6 LAN_D12 DSP_A7 LAN_D13 LAN_D14 LAN_D15 Decoupling Caps DSP_A8 3.3V DSP_A9 DSP_A10 10A1 11A1 12A1 13A1 14A1 15A1 16A1 USB_D0 USB_D1 USB_D2 USB_D3 USB_D4 USB_D5 USB_D6 USB_D7 USB_D8 USB_D9 USB_D10 USB_D11 USB_D12 USB_D13 USB_D14 USB_D15 0.1UF Decoupling 3.3V Decoupling Caps 3.3V ADDR_EN PI74AVC+16244 TSSOP48 0.1UF 0.1UF 0.1UF 0.1UF USB_D[0:15] 3.3V DSP_A11 DSP_A12 DSP_A13 DSP_A14 DSP_A15 0.1UF 0.1UF DSP_A[1:15] DSP_A1 DSP_A2 ADDR1 ADDR2 ADDR3 ADDR4 ADDR5 ADDR6 ADDR7 ADDR8 ADDR9 ADDR10 ADDR11 ADDR12 ADDR13 ADDR14 ADDR15 0.1UF 0.1UF 0.1UF 0.1UF ADDR[1:15]
DESCRIPTION
ENGR
DATE
06/14/04 08/27/04
APPR
DSP_D[0:31]
DSP_D0 DSP_D1 DSP_D2 DSP_D3 DSP_D4 DSP_D5 DSP_D6 DSP_D7 DSP_D8 DSP_D9 DSP_D10 DSP_D11 DSP_D12 DSP_D13 DSP_D14 DSP_D15 10B1 11B1 12B1 13B1 14B1 15B1 16B1
10B2 11B2 12B2 13B2 14B2 15B2 LAN_EN PI3B16234 TSSOP56 16B2
3.3V DSP_D16 DSP_D17 DSP_D18 DSP_D19 DSP_D20 DSP_D21 DSP_D22 DSP_D23 DSP_D24 PI3B16245 TSSOP48 561_PF12 DSP_A16 DSP_A17 AMS3 74LVC139 TSSOP16 BF561 ADDR RANGE PERIPHERAL BF537 ADDR RANGE PERIPHERAL USB_EN LAN_EN 0x2030 0000 0x2031 0000 0x2032 0000 0x2033 0000 0x2030 007F BF533 ADDR RANGE PERIPHERAL SEL=0 BF561 SEL=0 BF537 SEL=1 BF533 USB_IRQ LAN_D16 LAN_D17 LAN_D18 LAN_D19 LAN_D20 LAN_D21 LAN_D22 LAN_D23 LAN_D24 LAN_D25 LAN_D26 LAN_D27 LAN_D28 LAN_D29 LAN_D30 LAN_D31 533_PF9 533_PF10 LAN_EN 533_PF11 ADDR1 PI3B3257 TSSOP16 3.3V 4.7K 561_ADDR1 561_PF9_537_PF5 561_PF10_537_PF7 561_PF11_537_PF6 561_ADDR1 3.3V_USB ADDR1 561_ABE3
0.1UF
SW1.1
ADDR_EN ENABLED
SW1.1 HI-Z
FLAG_EN
SW1.2
FLAG_EN ENABLED
DSP_D25 DSP_D26 DSP_D27 DSP_D28 DSP_D29 DSP_D30 DSP_D31
SW1.2 HI-Z
LAN_ADDR1 LAN_IRQ 533_561_USB_IRQ USB_RESET
SW1.3
SW1.4
OPERATION OPERATION OPERATION DEFAULT SETTING
Denotes default position ADDR_EN FLAG_EN 533_561_USB_IRQ 537_DMAR
0x2031 FFFF 0x2032 FFFF 0x2033 FFFF
SWT018 DIP4
Populate Manual Jumper Settings Cotton Road Nashua, 03063 1-800-ANALOGD
ANALOG DEVICES
Approvals
Drawn Checked Engineering
0x2C00 0000 0x2C00 007F 0x2C01 0000 0x2C01 FFFF 0x2C02 0000 0x2C02 FFFF 0x2C03 0000 0x2C03 FFFF
0x2030 0000 0x2031 0000 0x2032 0000 0x2033 0000
0x2030 007F
Date
11/03/04
Title
0x2031 FFFF 0x2032 FFFF 0x2033 FFFF
BLACKFIN USB-LAN EZ-EXTENDER SWITCHES
Board
2-15-2005_9:16
Size
Date
A0187-2003
Sheet
REVISIONS
ADDR[2:6] ADDR2 ADDR3 ADDR4 ADDR5 ADDR6 RESET DMARD DMAWR DACK TEST TRST TMC2 XOUT RREF USB_VBUS VBUS
USB_D0 USB_D1 USB_D2 USB_D3 USB_D4 USB_D5 USB_D6 USB_D7 USB_D8 USB_D9 USB_D10 USB_D11 USB_D12 USB_D13 USB_D14 USB_D15 USB_LCLK0 USB_DREQ USB_VBUS USB_IRQ FER5 0.00 0.47UF 3.3V_USB INPUT OUTPUT ADP3330ART-25 SOT23-6 V_SELECT USB_D[0:15]
DESCRIPTION
ENGR
DATE
06/14/04 08/27/04
APPR
2.5V 2.5V FER1 1206 AVCC FER2 1206
USB_RESET USB_ALE
USB_EN USB_DMARD USB_DMAWR USB_DACK USB_EOT USB_TEST USB_TRST USB_TCM2 30MHZ OSC010
LD10 LD11 LD12 LD13 LD14 LD15 LCLKO
0.47UF
AGND
FER7 1206
DREQ RSDM
10PF
10PF
RSDP
1.5K
FER6
SHELL USB_TYPE_B CON009 4PIN
SHGND
3.3V_USB INPUT OUTPUT ADP3330ART-33 SOT23-6
2.43K
NET2272 TQFP64
0.01UF
0.47UF
0.47UF
AGND
AVCC Decoupling Caps
2.5V Decoupling Caps
3.3V_USB Decoupling Caps
3.3V_USB
AVCC 2.5V
VDDC1 VDDC2 VDD25 AVDD PVDD VDDIO1 VDDIO2 AVSS1 VDDIO3 AVSS2 VDD33 NET2272 TQFP64 VSSC1 VSSC2 VSSIO1 VSSIO2 VSSIO3 GND1 GND2 USB_ALE USB_DACK USB_EOT USB_TEST USB_TRST USB_TCM2 AGND USB_DREQ
3.3V_USB
3.3V_USB
0.1UF
0.01UF
10UF
0.1UF
0.01UF
0.1UF
0.01UF
10UF
0.1UF
0.01UF
0.1UF
0.01UF
10UF
AGND
USB_DMARD USB_DMAWR
Populate Manual Jumper Settings
ANALOG DEVICES
Approvals
Drawn Checked Engineering
Cotton Road Nashua, 03063 1-800-ANALOGD
Date
11/03/04
Title
BLACKFIN USB-LAN EZ-EXTENDER
Board
11-17-2004_17:56
Size
Date
A0187-2003
Sheet
REVISIONS
3.3V LAN_D[0:31] LAN_ADDR1 ADDR[2:15] ADDR2 ADDR3 ADDR4
DESCRIPTION
ENGR
DATE
06/14/04 08/27/04
APPR
3.3V_LAN
EECS EESK EEDO EEDI ENEEP IOS2 IOS1 IOS0 RESET LCLK RDYRTN DATACS CYCLE W/R~ VLBUS LAN91C111 TQFP128
ADDR5 ADDR6 ADDR7 ADDR8 ADDR9 ADDR10 3.3V_LAN ADDR11 ADDR12 ADDR13 ADDR14 MicroWire Serial EEPROM 93LC46B SOIC8 ADDR15
10/100 ETHERNET
ABE0 ABE1 561_ABE2 561_ABE3 LAN_EN RESET LAN_ADS LAN_LCLK LAN_RDYRTN LAN_DATACS LAN_CYCLE LAN_W/R~ LAN_VLBUS
SWT018 DIP4
LAN_D0 LAN_D1 LAN_D2
IDC2X1
Default LAN_D3 LAN_D4 LAN_D5 LAN_D6 LAN_D7 LAN_D8 LAN_D9 LAN_D10 LAN_D11 LAN_D12 LAN_D13 LAN_D14 LAN_D15 LAN_D16 LAN_D17 LAN_D18 LAN_D19 LAN_D20 LAN_D21 LAN_D22 LAN_D23 LAN_D24 LAN_D25 LAN_D26 LAN_D27 LAN_D28 LAN_D29 LAN_D30 LAN_D31 1206 1206 3.3V_LAN AVDD1 AVDD2 GND1 GND2 GND3 GND4 GND5 GND6 GND7 GND8 GND9 GND10 AGND1 AGND2 RXD0 RXD1 RXD2 RXD3 11.0K 1206 VDD1 VDD2 VDD3 VDD4 VDD5 VDD6 VDD7 VDD8 TPO+ TPO17 TPI+ TPI20 CNTRL RBIAS 3.3V_LAN 24.9 24.9 0.00 49.9 49.9 0.01UF
0.00
IDC2X1
Default
24.9
24.9
CON_RJ45B 8PIN
10/100
TXD0 TXD1
ETHERNETTXD2114
TXD3 TXEN100 CRS100 COL100 RX_DV RX_ER MCLK RX25 TX25 CSOUT 3.3V_LAN
ARDY SRDY INTR0 LDEV LEDA LEDB
LAN_ARDY
LED1 AMBER-SMT LED001
LED2 AMBER-SMT LED001
LAN_IRQ
XTAL2 XTAL1
LAN_LCLK LAN_RDYRTN LAN_DATACS LAN_CYCLE LAN_W/R~ LAN_VLBUS LAN_ARDY LAN_ADS
X25OUT LAN91C111 TQFP128
SW2.1
SW2.2
SW2.3
SW2.4
Decoupling 3.3V_LAN 25MHZ OSC005
EEPROM DISABLED
EEPROM ENABLED
Denotes Default Setting DENOTES DON'T CARE VALUE PLEASE REFER SMSC DATASHEET MORE INFO IOS[2:0] 0.1UF 30PF 1206
30PF 1206
Decoupling Caps 3.3V_LAN
Decoupling Caps
3.3V_LAN FER3 1206
0.00 1206
Populate Manual Jumper Settings
0.1UF
0.1UF
0.1UF
0.1UF
0.1UF
0.1UF
0.1UF
0.1UF
SHGND2
ANALOG DEVICES
Approvals
Drawn Checked Engineering
Cotton Road Nashua, 03063 1-800-ANALOGD
Date
11/03/04
Title
BLACKFIN USB-LAN EZ-EXTENDER
Board
2-15-2005_9:16
Size
Date
A0187-2003
Sheet
REVISIONS
POWER OVER ETHERNET CIRCUITRY WITH ADSP-BF537 EZ-KIT LITE ONLY
DESCRIPTION
ENGR
DATE
06/14/04 08/27/04
APPR
SBM1040 DIO004 0.1UF SMAJ58A DIO003 POE_VCC3 HD01 MDIP4 68.1 VPORTP RCLASS PGND1 PGND2 PGND3 PGND4 SIGDISA VPORTN LTC4267 SSOP16 PVCC PWRGD NGATE SENSE ITH/RUN POUT POE_PWR
5V@1.7A
PA1134 ICS005 4.7UF 4.7UF 6.81K 0.1UF SI3440DV TSOP6 AGND2 PS2911-1 ICS006 TLV431A SOT23-3 3.32K FER4 1206 680UF 0.1UF
POE_VCC+
LL4148 DL35
10.0K 1206
AGND2
AGND2
0.12 0603
AGND2
AGND2
INTERFACE
MDIO
WARNING: EZ-KIT LITE MUST POWERED WHEN THESE JUMPERS POPULATED.
RXD3 RXD2 RXD1 RXD0
V_SELECT
RX_DV RX_CLK RX_ER TX_ER
POE_PWR
IDC3X1
TX_CLK TX_EN TXD0 TXD1 TXD2 TXD3
SOURCE EZ-KIT POWER TEST MODE POWER ADSP-BF537 EZ-KIT LITE ONLY
SETTING
JUMPER
VCC1 MDIO RXD3 RXD2 RXD1 RXD0 RX_DV RX_CLK RX_ER TX_ER TX_CLK TX_EN TXD0 TXD1 TXD2 TXD3 VCC2 CON036 40PIN
VCC3 GND1 GND2 GND3 GND4 GND5 GND6 GND7 GND8 GND9 GND10 GND11 GND12 GND13 GND14 GND15 GND16 GND17 GND18 VCC4
Populate Manual Jumper Settings
WITH ADSP-BF537 EZ-KIT LITE ONLY
*DENOTES DEFAULT SETTING
ANALOG DEVICES
Approvals Date
11/03/04 Size Title Board
2-15-2005_9:16
Cotton Road Nashua, 03063 1-800-ANALOGD
Drawn Checked Engineering
BLACKFIN USB-LAN EZ-EXTENDER POE, MII, SELECTION A0187-2003
Sheet
Date
INDEX
ADDR enable switch (SW1.1), architecture, EZ-Extender, Asynchronous Memory Bank, viii
interfaces EZ-KIT Lite, switch (SW2.2, SW2.3, SW2.4),
bill materials,
jumpers (power), (LAN power), (link power), jumper settings,
CAT5E Ethernet cable, customer support,
dimensions,
device model, viii power jumper (JP2), LAN91C111 Ethernet processor, link jumper (JP3),
Ethernet device, viii interface, viii expansion interface, EZ-KIT Lite, viii interface (J1-3), EZ-Extender interfacing with EZ-KIT Lite, system architecture,
address,
notation conventions,
FLAGS enable switch (SW1.2), Power-over-Ethernet, viii, power select jumper (JP1),
Blackfin USB-LAN EZ-Extender Manual
INDEX
product overview, viii
switch settings,
serial enable switch (SW2.1), SMSC 91C111 device, switches SW1.1 (addr enable), SW1.3 (USB enable), SW1.4 (test mode enable), SW2.1 (serial enable), SW2.2-2.4 (IOS), SW2.2 (flag enable),
test mode enable switch (SW1.4),
device, viii enable switch (SW1.3),
Blackfin USB-LAN EZ-Extender Manual
Other recent searches
TM5670 - TM5670 TM5670 Datasheet
OC-3 - OC-3 OC-3 Datasheet
OC-192 - OC-192 OC-192 Datasheet
CSD16323Q3 - CSD16323Q3 CSD16323Q3 Datasheet
CP-8 - CP-8 CP-8 Datasheet
AN1524 - AN1524 AN1524 Datasheet
ADR390 - ADR390 ADR390 Datasheet
ADR391 - ADR391 ADR391 Datasheet
ADR392 - ADR392 ADR392 Datasheet
ADR395 - ADR395 ADR395 Datasheet
Privacy Policy | Disclaimer
© 2012 Datasheet Archive
