Revision 1.0, January 2005 Part Number 82-000870-01 Copyright Inf

The Datasheet Archive - 100 Million Datasheets from 7500 Manufacturers.

Revision 1.0, January 2005 Part Number 82-000870-01 Copyright Inf

Datasheet Thumbnail

Top Searches for this datasheet

Blackfin EZ-Extender Manual
Revision 1.0, January 2005 Part Number 82-000870-01
Copyright Information
2005 Analog Devices, Inc., RIGHTS RESERVED. This document reproduced form without prior, express written consent from Analog Devices, Inc. Printed USA.
Limited Warranty
EZ-Extender warranted against defects materials workmanship period year from date purchase from Analog Devices from authorized dealer.
Disclaimer
Analog Devices, Inc. reserves right change this product without prior notice. Information furnished Analog Devices believed accurate reliable. However, responsibility assumed Analog Devices use; infringement patents other rights third parties which result from use. license granted implication otherwise under patent rights Analog Devices, Inc.
Trademark Service Mark Notice
Analog Devices logo, Blackfin, VisualDSP++, EZ-KIT Lite registered trademarks Analog Devices, Inc. other brand product names trademarks service marks their respective owners.
Regulatory Compliance
Blackfin EZ-Extender been certified comply with essential requirements European directive 89/336/EEC (inclusive 93/68/EEC) and, therefore, carries "CE" mark. Blackfin EZ-Extender been appended Analog Devices Development Tools Technical Construction File referenced "DSPTOOLS1" dated December 1997 awarded Certification appointed European Competent Body file.
EZ-KIT Lite evaluation system contains (electrostatic discharge) sensitive devices. Electrostatic charges readily accumulate human body equipment discharge without detection. Permanent damage occur devices subjected high-energy discharges. Proper precautions recommended avoid performance degradation loss functionality. Store unused EZ-KIT Lite boards protective shipping package.
CONTENTS
PREFACE
Product Overview Purpose This Manual Intended Audience Manual Contents What's This Manual Technical Customer Support xiii Supported Products xiii Product Information Related Documents Notation Conventions
EZ-EXTENDER INTERFACES
EZ-Extender Setup Analog Audio Interface Analog Video Interface Camera Module Interfaces Flat Panel Display Interface
Blackfin EZ-Extender Manual
CONTENTS
EZ-EXTENDER HARDWARE REFERENCE
System Architecture Jumpers Video Test Loopback Jumpers (JP1.1/2, JP1.3/4, JP1.5/6) Connector Voltage Selection Jumper (JP2) Source Selection Jumpers (JP3.3/5/7, JP3.4/6/8) PDWN Connection Jumper (JP3.9/10) Decoder HSync Disconnect Jumper (JP3.11/12) Decoder VSync Connection Jumper (JP3.13/14) Encoder HRef Connection Jumper (JP3.15/16) 2-10 Encoder VSync Connection Jumper (JP3.17/18) 2-10 Decoder Output Enable Jumper (JP3.19/20) 2-10 SNAPSHOT_FODD Disconnect Jumper (JP3.21/22) 2-10 Clock Setup Jumpers (JP4.1/2, JP4.3/4, JP4.5/6, JP4.7/8) 2-10 PPI0 D8-15 Enable Jumper (JP5.1/2) 2-11 VID_OUT Data Control Jumpers (JP5.3/4, JP5.5/6) 2-11 PPI0_SYNC1 Direction Setup Jumper (JP6.1/3/5) 2-12 PPI0_SYNC2 Direction Setup Jumper (JP6.2/4/6) 2-12 Enable Jumper (JP7.1/2) 2-13 SPORT Data Connection Jumpers (JP7.3/4, JP7.5/6) 2-13 VID_OUT Sync Source Select Jumpers (JP8.1/3/5, JP8.2/4/6) 2-13 VID_OUT Sync Enable Jumper (JP8.7/8) 2-13 AV_RESET Source Jumper (JP9.1/3/5) 2-14
Blackfin EZ-Extender Manual
CONTENTS
PPI0_D Direction Setup Jumper (JP9.2/4/6) 2-14 Audio Loopback Jumpers (JP10.1/2, JP10.3/4) 2-14
BILL MATERIALS INDEX
Blackfin EZ-Extender Manual
CONTENTS
viii
Blackfin EZ-Extender Manual
PREFACE
Thank purchasing Blackfin® EZ-Extender, Analog Devices, Inc. (ADI) extension board EZ-KIT Lite® evaluation system ADSP-BF533, ADSP-BF537, ADSP-BF561 Blackfin processors. Blackfin processors embedded processors that support Media Instruction Computing (MISC) architecture. This architecture natural merging RISC, media functions, digital signal processing characteristics towards delivering signal processing performance microprocessor-like environment. EZ-KIT Lite EZ-Extender designed used conjunction with VisualDSP++® development environment. VisualDSP++ offers powerful programming tool with flexibility that significantly decreases time required port software code processor, reducing time-to-market. learn more about Analog Devices development software,
Product Overview
Blackfin EZ-Extender separately sold extension board that plugs onto expansion interface ADSP-BF533, ADSP-BF537, ADSP-BF561 EZ-KIT Lite evaluation system. extension board aids design prototyping phases ADSP-BF533, ADSP-BF537, ADSP-BF561 processor targeted applications.
Blackfin EZ-Extender Manual
Product Overview
board extends capabilities evaluation system providing connection video decoder, video encoder, multiple camera evaluation boards, flat panel display, 3-stereo input channel, 2-stereo output channel audio codec. following list Blackfin EZ-Extender interfaces. Analog Audio Interface AD1836A Analog Devices audio codec five audio jacks, stacked connector Analog Video Interface ADV7183B video decoder with three input phono jacks ADV7179 video encoder with three output phono jacks OmniVision Camera Module Interface Connection OmniVision Camera Evaluation Modules, example: OV6630AA 32-pin, right angle, spacing, female socket Micron Camera Module Interface Connection Micron Camera Evaluation Modules, example: MT9V022 26-pin, right angle, spacing, female socket Kodak Camera Module Interface Connection Kodak Camera Evaluation Modules, example: KAC-9628 28-pin, right angle, spacing, female socket
Blackfin EZ-Extender Manual
Preface
Flat Panel Display Interface Connection Flat Panel Displays, example, NL6448BC20-08E DF9B-31S-1V connector Before using interfaces, follow setup procedure "A-V EZ-Extender Setup" page 1-1. Example programs available demonstrate capabilities Blackfin EZ-Extender board.
Purpose This Manual
Blackfin EZ-Extender Manual describes operation configuration components extension board. schematic bill materials provided reference future Blackfin processor board designs.
Intended Audience
This manual user's guide reference Blackfin EZ-Extender. Programmers familiar with Analog Devices Blackfin processor architecture, operation, development tools primary audience this manual. Programmers unfamiliar with VisualDSP++ EZ-KIT Lite evaluation software should refer ADSP-BF533, ADSP-BF537, ADSP-BF561 Evaluation System Manual, VisualDSP++ online Help, user's getting started guides. locations these documents, refer "Related Documents".
Blackfin EZ-Extender Manual
Manual Contents
Manual Contents
manual consists Chapter "A-V EZ-Extender Interfaces" page Provides basic board information. Chapter "A-V EZ-Extender Hardware Reference" page Provides information hardware aspects board. Appendix "Bill Materials" page Provides list components used manufacture EZ-Extender board. Appendix "Schematics" page Provides resources allow EZ-KIT Lite board-level debugging reference design. This appendix part online Help. online Help viewers should version Blackfin EZ-Extender Manual located Docs\EZ-KIT Lite Manuals folder installation schematics. Alternatively, schematics found Analog Devices site, www.analog.com/processors.
What's This Manual
This first edition Blackfin EZ-Extender Manual.
Blackfin EZ-Extender Manual
Preface
Technical Customer Support
reach processor Tools Support following ways. Visit Embedded Processing processor products site
E-mail tools questions
dsptools.support@analog.com
E-mail processor questions
dsp.support@analog.com
Phone questions 1-800-ANALOGD Contact your Analog Devices, Inc. local sales office authorized distributor Send questions mail
Analog Devices, Inc. Technology P.O. 9106 Norwood, 02062-9106
Supported Products
Blackfin EZ-Extender designed extension board ADSP-BF533, ADSP-BF537, ADSP-BF561 EZ-KIT Lite evaluation systems.
Blackfin EZ-Extender Manual
xiii
Product Information
Product Information
obtain product information from Analog Devices site, from product CD-ROM, from printed publications (manuals). Analog Devices online www.analog.com. site provides information about broad range products-analog integrated circuits, amplifiers, converters, digital signal processors.
Related Documents
information product related development software, following publications. Table Related Processor Publications
Title ADSP-BF533 Embedded Processor Datasheet ADSP-BF536/ADSP-BF537 Embedded Processor Datasheet ASP-BF561 Blackfin Embedded Symmetric Multi-Processor Datasheet ADSP-BF533 Blackfin Processor Hardware Reference ADSP-BF537 Blackfin Processor Hardware Reference ASP-BF561 Blackfin Processor Hardware Reference Blackfin Processor Instruction Reference Description General functional description, pinout, timing.
Description internal processor architecture register functions
Description allowed processor assembly instructions.
Blackfin EZ-Extender Manual
Preface
Table Related VisualDSP++ Publications
Title ADSP-BF533 EZ-KIT Lite Evaluation System Manual ADSP-BF537 EZ-KIT Lite Evaluation System Manual ADSP-BF561 EZ-KIT Lite Evaluation System Manual VisualDSP++ User's Guide VisualDSP++ Assembler Preprocessor Manual VisualDSP++ C/C++ Complier Library Manual Blackfin Processors VisualDSP++ Linker Utilities Manual VisualDSP++ Loader Manual Description Description EZ-KIT Lite features usage. Note: ADSP-BF537 EZ-KIT Lite, there additional Getting Started with ADSP-BF537 EZ-KIT Lite. Description VisualDSP++ features usage Description assembler function commands Description complier function commands Blackfin processors Description linker function commands Description loader function commands
documentation available online. Most documentation available printed form. Visit Technical Library site access processor tools manuals data sheets:
Blackfin EZ-Extender Manual
Notation Conventions
Notation Conventions
Text conventions used this manual identified described follows.
Example Close command (File menu)
{this that}
Description Titles reference sections indicate location item within VisualDSP++ environment's menu system (for example, Close command appears File menu). Alternative required items syntax descriptions appear within curly brackets separated vertical bars; read example this that. other required. Optional items syntax descriptions appear within brackets separated vertical bars; read example optional this that. Optional item lists syntax descriptions appear within brackets delimited commas terminated with ellipse; read example optional comma-separated list this. Commands, directives, keywords, feature names text with letter gothic font. Non-keyword placeholders appear text with italic style format. Note: correct operation, Note provides supplementary information related topic. online version this book, word Note appears instead this symbol. Caution: Incorrect device operation result Caution: Device damage result Caution identifies conditions inappropriate usage product that could lead undesirable results product damage. online version this book, word Caution appears instead this symbol. Warning: Injury device users result Warning identifies conditions inappropriate usage product that could lead conditions that potentially hazardous devices users. online version this book, word Warning appears instead this symbol.
[this that]
[this,.]
.SECTION
filename
Blackfin EZ-Extender Manual
Preface
Additional conventions, which apply only specific chapters, appear throughout this document.
Blackfin EZ-Extender Manual
xvii
Notation Conventions
xviii
Blackfin EZ-Extender Manual
EZ-EXTENDER INTERFACES
After setup procedure custom system utilizing Blackfin EZ-Extender, ADSP-BF533, ADSP-BF537 ADSP-BF561 EZ-KIT Lite, evaluation module, chapter describes each evaluation interfaces extender supports. information presented following order. "Analog Audio Interface" page "Analog Video Interface" page "Camera Module Interfaces" page "Flat Panel Display Interface" page
EZ-Extender Setup
very important components system containing EZ-Extender before applying power that system. following procedure recommended correct setup. Power your system when these steps completed: Read applicable design interface section this chapter-the text provides overview capabilities interface. Read "System Architecture" page understand physical connections extension board. detailed information, refer "Schematics page B-1".
Blackfin EZ-Extender Manual
Analog Audio Interface
jumpers EZ-Extender board. block diagram Figure page conjunction with "Jumpers" page 2-7. switches jumpers EZ-KIT Lite board. already, familiarize yourself with documentation schematics EZ-KIT Lite (see "Related Documents" page -xiv). Compare expansion interface signals EZ-Extender board with signals EZ-KIT Lite board ensure there contention. example, necessary disable other devices connected Parallel Peripheral Interface (PPI) processor, change routing clocks, disable push buttons. Configure other interfacing boards, example, another EZ-Extender camera evaluation board.
Analog Audio Interface
audio application, EZ-Extender uses AD1836A multichannel audio codec. AD1836A high-performance, single-chip codec that provides three stereo digital-to-analog converters (outputs) stereo analog-to-digital converters (inputs) using ADI's patented multi-bit sigma-delta architecture. board includes port, allowing processor adjust volume other parameters. general overview audio interface connections, Figure page 2-3. more detailed information, "Schematics page B-1". expansion interface interfaces with serial port AD1836A codec. processor capable transferring data audio codec time-division multiplexed (TDM) mode. mode allows codec operate sample rate allows only channels output. mode operate maximum
SPORT0
Blackfin EZ-Extender Manual
EZ-Extender Interfaces
sample rate allows simultaneous input output channels. operate mode, JP7.1/2 jumper must installed. more information, "I2S Enable Jumper (JP7.1/2)" page 2-13. internal registers AD1836A audio codec programmed port processor. (For information program configuration registers, refer AD1836A datasheet.) AD1836A codec reset comes either from flag located PPI1_D11 expansion interface from EZ-KIT Lite reset signal. information configure reset, "AV_RESET Source Jumper (JP9.1/3/5)" page 2-14. Before using interface, follow steps "A-V EZ-Extender Setup" page 1-1. Example programs demonstrating capabilities audio interface included EZ-Extender installation directory. more information about AD1836A, http://www.analog.com search AD1836A.
Analog Video Interface
EZ-Extender supports video input output applications with on-board video encoder decoder. ADV7179 video encoder provides three output channels analog video, while ADV7183B video decoder provides three input channels analog video. Both encoder decoder connect PPI0 expansion interface, while encoder also connect PPI1 processor ports). general overview analog video interface connectors, Figure page 2-3. more detailed information, "Schematics page B-1".
Blackfin EZ-Extender Manual
Camera Module Interfaces
ADV7179 ADV7183B, jumpers related data signals, frame sync signals, clock signal. program internal register video devices, configure Wire Interface signals (see "TWI Source Selection Jumpers (JP3.3/5/7, JP3.4/6/8)" page 2-7). Finally, determine source encoder decoder reset (see "AV_RESET Source Jumper (JP9.1/3/5)" page 2-14.) Before using interface, follow steps "A-V EZ-Extender Setup" page 1-1. Example programs demonstrating capabilities analog video interface included EZ-Extender installation directory. more information about ADV7179 ADV7183B, http://www.analog.com search ADV7179 ADV7183B.
Camera Module Interfaces
EZ-Extender three right-angle connectors (J4, with control signals necessary interface with three different manufactures camera evaluation modules. general overview camera module interface connections, Figure page 2-4. more detailed information, "Schematics page B-1". Figure shows orientation camera modules, each camera connects board. connector designated Micron camera sensor evaluation module. interface been tested with Micron MT9V022 camera evaluation module. information about Micron camera sensors evaluation boards, http://www.micron.com. connector designated OmniVision camera sensor evaluation module. interface been tested with OmniVision OV6630AA camera evaluation module. information about OmniVision camera sensors evaluation boards, http://www.ovt.com.
Blackfin EZ-Extender Manual
EZ-Extender Interfaces
Micron
Kodak Audio
EZ-KIT
Figure 1-1. Camera Orientation connector designated Kodak camera sensor evaluation module. interface been tested with Kodak KAC-9628 camera evaluation module. information about Kodak camera sensors evaluation boards, http://www.kodak.com. connect Blackfin EZ-Extender camera module, first determine source clock. learn about possible clock settings, refer "PPI Clock Setup Jumpers (JP4.1/2, JP4.3/4, JP4.5/6, JP4.7/8)" page 2-10. Then direction data frame sync signals, which depend upon camera's configuration. data must input port. more information, refer "System Architecture" page "Jumpers" page 2-7. Before using these interfaces, follow steps "A-V EZ-Extender Setup" page 1-1.
Blackfin EZ-Extender Manual
Flat Panel Display Interface
Example programs demonstrating capabilities camera module interface included EZ-Extender installation directory.
Flat Panel Display Interface
Flat Panel Display (FPD) interface consists 31-pin, connector linked port frame sync signals processor. general overview display interface connections, Figure page 2-4. more detailed information, "Schematics page B-1". timing functional analysis required determine specific module connect Blackfin EZ-Extender. example display that connect extender NL6448BC20-08 display (http://www.ee.nec.de/). Please note that power backlight feature module must provided customer (use backlight inverter recommended manufacturer). also necessary purchase cable connect EZ-Extender display. example such cable FDC31/xxxxAFF03 from Axon Cable (http://www.axon-cable.com, part number FDC31/xxxxAFF03). Different length cables available. Before using interface, follow steps "A-V EZ-Extender Setup" page 1-1. Example programs demonstrating capabilities flat panel display interface included EZ-Extender installation directory.
Blackfin EZ-Extender Manual
EZ-EXTENDER HARDWARE REFERENCE
This chapter describes hardware design EZ-Extender. following topics covered. "System Architecture" page Describes configuration extension board explains board components interface with processor EZ-KIT Lite. "Jumpers" page Describes function configuration jumpers.
Blackfin EZ-Extender Manual
System Architecture
System Architecture
block diagram Blackfin EZ-Extender shown Figure 2-1. shown diagram analog audio interface, which simple connection between serial port processor AD1836A audio codec. audio interface connects directly SPORT0 expansion interface. Figure 2-1, unidirectional buffers show triangle symbols, while bidirectional buffers shown overlapping triangles. both types buffers, output-enable signal comes active LOW. bidirectional buffers, second signal direction shown. When this pulled HIGH, buffer driving direction arrow center, when LOW, buffer driving opposite direction. Before applying power system, follow steps "A-V EZ-Extender Setup" page 1-1. Video interfaces split into main signal sets: VID_IN VID_OUT. Both signal sets consist 16-bit data bus, frame sync signals, data clock. VID_IN connects video decoder camera interfaces. VID_IN connects only PPI0 EZ-KIT Lite. VID_OUT connects video encoder flat panel display interface. expansion interface, VID_OUT connects either PPI0 PPI1 EZ-KIT Lite. Table summarizes signals coming going expansion interface connectors.
Blackfin EZ-Extender Manual
EZ-Extender Hardware Reference
VID_OUT_D[7:0] JP3.15/16 FLAG_SDA PPI1_D2 FLAG_SCL_ DIR_CTRL PPI1_D3 PPI1_D11 RESET PPI0_DAT[15-0] JP9.2/4/6
T/~R
Encoder (Out) P[7:0] HSYNC VSYNC RESET DAC_A DAC_B DAC_C
JP3.19/20
VID_IN_D[7:0] JP3.11/12 JP3.13/14
Decoder (In) P[15:8] HSYNC VSYNC CLK_OUT RESET Micron DATA[9:0] LN_VALID FRAME_VALID AVIN1 AVIN4 AVIN5
JP3.3/5/7
JP3.17/18
JP3.4/6/8
JP9.1/3/5
Expansion Interface Signals
also JP5.1/2
VID_IN_D[15:0]
VID_OUT_D[15:0] 3.3v
JP5.5/6
PPI1_DAT[15-0] JP5.3/4
T/~R
FPDI RGB[15:0]
PCLK TX_CLK RESET V_IN
JP8.1/3/5 PPI1_SYNC1 JP8.2/4/6 PPI1_SYNC2 JP8.7/8 PPI0_SYNC1
V_IN OmniVision Y[7:0] UV[7:0] HREF VSYNC PCLK EXCLK PWDN FODD RESET
VID_IN_SYNC1_HSYNC JP6.1/3/5
T/~R
PPI0_SYNC2 VID_IN_SYNC2_VSYNC JP6.2/4/6
T/~R
V_IN
Eastman Kodak
27MHz PPI0_CLK PPI1_CLK JP3.9-10 PPI1_D10 SNAPSHOT_ FODD_SSEL PPI1_D15 Pull-up JP3.21/22 Represents location lowest number jumper series JP1, JP5.1/2, JP7, JP10 Audio Interface shown this block diagram.
D[11:0] HSYNC VSYNC PCLK MCLK PWDN SNAPSHOT EXT_SYNC RESET V_IN
Blackfin EZ-Extender Manual
System Architecture
Table 2-1. Signals Expansion Interface Connectors
Net/Bus Name (Direction)
PPI0_D[0:15]
EZ-Extender Function
Relevant Configuration Jumpers
JP5.3/4, JP9.2/4/5
(Bi)
Connects processor's PPI0 data pins VID_OUT_D[0:15] busses, depending jumper settings. This allows PPI0 interface with possible video interfaces board. This bidirectional, where direction fixed with jumper controlled flag pin.
VID_IN_D[0:15]
PPI0_CLK
(Output)
clock related data PPI0. This come from onboard oscillator, from video interfaces, from socket that allows user-supplied oscillator. frame sync signal going processor's
PPI0_SYNC1 pin. signal behaves HSYNC HREF video interfaces. signal also used drive FPDI signal. signal bidirec-
JP4.1/2, JP4.3/4, JP4.5/6, JP4.7/8 JP6.1/3/5, JP8.1/3/5, JP8.7/8
PPI0_SYNC1
(Bi)
tional, where direction fixed with jumper controlled flag pin.
PPI0_SYNC2
frame sync signal going processor's
PPI0_SYNC2 pin. signal behaves VSYNC VREF video interfaces. signal also used drive FPDI signal. This signal bidirec-
(Bi)
JP6.2/4/6, JP8.2/4/6, JP8.7/8
tional, where direction fixed with jumper controlled flag pin.
PPI1_D[0:15]
(Bi)
Connects processors PPI1 data pins bus. VID_OUT_D[0:15] interfaces with output video interfaces (FPDI video encoder). bidirectional intended input. Changing direction necessary only test purposes allows PPI0 loop-back PPI1. have other functionality (see below).
VID_OUT_D[0:15]
JP5.3/4, JP5.5/6, JP3.9/10, JP3.3/5/7 JP3.4/6/8
PPI1_D10
(Bi)
Multifunction that typically functions PPI1 but, with jumper, also connect PDWN input OmniVision interface Kodak interface.
JP3.9/10, JP5.3/4, JP5.5/6
Blackfin EZ-Extender Manual
EZ-Extender Hardware Reference
Table 2-1. Signals Expansion Interface Connectors (Cont'd)
Net/Bus Name (Direction)
PPI1_D2
EZ-Extender Function
Relevant Configuration Jumpers
(Bi)
PPI1
Multifunction typically functions JP3.3/5/7, also function data signal pro- JP5.3/4, cessor's Wire Interface (TWI). Used program JP5.5/6 internal configuration registers most video interfaces. Multifunction typically functions JP3.4/6/8, also function data signal pro- JP5.3/4, cessor's TWI. Used program internal configuration JP5.5/6 registers most video interfaces. systems whose processor does have TWI, sig- JP3.3/5/7 connects processor's flag pins emulate data configure internal configure registers most video interfaces. systems whose processor does have TWI, sig- JP3.4/6/8 connects processor's flag pins emulate clock signal configure internal configure registers most video interfaces.
PPI1_D3
(Bi)
PPI1
FLAG_SDA
(Bi)
FLAG_SCL_DIR_ CTRL
(Input)
PPI1_CLK
(Output)
clock driving EZ-KIT Lite's PPI1 clock input. source this clock PPI0_CLK, onboard oscillator, socket accepting oscillators other frequencies. signal driven signal FPDI. output going FPDI disabled jumper. signal driven signal FPDI. output going FPDI disabled jumper. Audio codec slave select signal; also connect SNAPSHOT input Kodak interface FODD output OmniVision interface. serial clock used program control register AD1836A audio codec. serial output data signal used program control register AD1836A audio codec.
JP4.1/2, JP4.3/4, JP4.5/6, JP4.7/8 JP8.1/3/5, JP8.7/8 JP8.2/4/6, JP8.7/8 JP3.21/22
PPI1_FS1
(Input)
PPI1_FS2
(Input)
SNAPSHOT_FODD _SSEL
(Bi)
(Input)
MOSI
(Output)
Blackfin EZ-Extender Manual
System Architecture
Table 2-1. Signals Expansion Interface Connectors (Cont'd)
Net/Bus Name (Direction)
MISO
EZ-Extender Function
Relevant Configuration Jumpers
(Output)
RSCLK0
serial input data signal used read control register AD1836A audio codec. Processor's SPORT0 receive clock signal connected serial clock digital side audio codec analog input. mode, signal connect TSCLK0 net. Processor's SPORT0 receive frame sync signal connected frame sync digital side audio codec analog input. mode, signal connect TFS0 net. Connection data output audio codec. disconnected with jumper signal needed another purpose. Secondary connection data output audio codec. disconnected with jumper signal needed used another purpose. Processor's SPORT0 transmit clock signal. Connects serial clock digital side audio codec's analog output. mode, signal connect RSCLK0 net. Processor's SPORT0 transmit frame sync signal. Connects frame sync digital side audio codec analog output. mode, signal connect RFS0 net. Connection data input audio codec. Secondary connection data input audio codec.
JP7.1/2
(Bi)
RFS0
JP7.1/2
(Bi)
DR0PRI
JP7.3/4
(Output)
DR0SEC
JP7.5/6
(Output)
TSCLK0
JP7.1/2
(Bi)
TFS0
JP7.1/2
(Bi)
DT0PRI
(Input)
DT0SEC
(Input)
Blackfin EZ-Extender Manual
EZ-Extender Hardware Reference
Jumpers
Before using Blackfin EZ-Extender, follow steps "A-V EZ-Extender Setup" page 1-1. Figure shows locations jumper headers. jumper headers divided show placement rotation each jumper. jumpers described pins header which jumpers placed. example, JP3.4/6/8 refers single jumper that placed across pins pins JP3. dark indicates each header.
Video Test Loopback Jumpers (JP1.1/2, JP1.3/4, JP1.5/6)
test purposes only, video test jumpers used loop-back video encoder's output signals video decoder's input signals. default, none these jumpers installed.
Connector Voltage Selection Jumper (JP2)
camera module display interfaces powered extender. actual voltage these interfaces, 3.3V determined placement jumper (see Table 2-2).
Source Selection Jumpers (JP3.3/5/7, JP3.4/6/8)
fact that some Blackfin processors feature built-in Wire Interface (TWI), while others need emulate interface with programmable flags, jumpers provided plug EZ-Extender both sources (see Table 2-3).
Blackfin EZ-Extender Manual
Jumpers
JP10
Figure 2-2. Jumper Locations Table 2-2. Jumper Locations their Connector Voltages
Jumper Location
JP2.1/2 JP2.2/3
Connector Voltage 3.3V power
installed
Blackfin EZ-Extender Manual
EZ-Extender Hardware Reference
Table 2-3. Jumper Locations Interface Sources
Jumper Locations
JP3.3/5 JP3.5/7
Interface Source Programmable Flags Processor's
JP3.4/6 JP3.6/8
PDWN Connection Jumper (JP3.9/10)
Depending application, PDWN OmniVision Kodak cameras left floating controlled flag (see Table 2-4). Table 2-4. PWDN Connections
JP3.9/10 Uninstalled Installed PDNW Connection PDWN used, default, cameras function standard mode. PDWN functionality cameras controlled processor flag pin.
Decoder HSync Disconnect Jumper (JP3.11/12)
connect horizontal sync signal video decoder PPI0 frame sync signal processor, install JP3.11/12 jumper; otherwise, decoder's horizontal sync disconnected.
Decoder VSync Connection Jumper (JP3.13/14)
connect vertical sync signal video decoder PPI0 frame sync signal processor, install JP3.13/14 jumper; otherwise, decoder's vertical sync disconnected.
Blackfin EZ-Extender Manual
Jumpers
Encoder HRef Connection Jumper (JP3.15/16)
connect horizontal sync signal video encoder PPI0 frame sync signal processor, install JP3.15/16 jumper; otherwise, encoder's horizontal reference disconnected.
Encoder VSync Connection Jumper (JP3.17/18)
connect vertical sync signal video encoder PPI0 frame sync signal processor, install JP3.17/18 jumper; otherwise, encoder's vertical sync disconnected.
Decoder Output Enable Jumper (JP3.19/20)
When installed, JP3.19/20 jumper enables video decoder's data output signals VID_IN bus.
SNAPSHOT_FODD Disconnect Jumper (JP3.21/22)
SNAPSHOT_FODD EZ-Extender general-purpose flag pin. flag connects both SNAPSHOT signal Kodak camera evaluation board FODD control signal OmniVision camera evaluation board. install jumper unless processor needs control signals. flag also connects select AD1836A audio codec-when audio interfaces being used, install this jumper.
Clock Setup Jumpers (JP4.1/2, JP4.3/4, JP4.5/6, JP4.7/8)
PPI_CLK signals PPI0 PPI1 setup using clock setup jumpers. Table shows results jumper connections. more information about clock settings, refer Figure page 2-4.
2-10
Blackfin EZ-Extender Manual
EZ-Extender Hardware Reference
Table 2-5. Jumper Results
Jumper
JP4.1/2
Result Connects EXT_VID_CLK onboard oscillator. more information about EXT_VID_CLK signal, description JP4.3/4. Connects PPI0_CLK EXT_VID_CLK net. EXT_VID_CLK external clock, which drives input clock camera module interface connectors, plus flat panel display connector. Depending installation other jumpers, EXT_VID_CLK generated PIXEL_CLK net, VDEC_CLKOUT net, socket (U8), onboard oscillator. Connects VDEC_CLKOUT PPI0_CLK. VDEC_CLKOUT drives PPI0 clock when video decoder used. Connects PIXEL_CLK net, which output from three camera module interfaces, PPI0_CLK.
JP4.3/4
JP4.5/6
JP4.7/8
PPI0 D8-15 Enable Jumper (JP5.1/2)
JP5.1/2 jumper, when installed, disables upper 8-bits PPI0 data bus. This allows signals connected upper 8-bits data EZ-KIT Lite used another purpose. disable reuse upper 8-bits VID_IN PPI0 data busses, install JP5.1/2 jumper.
VID_OUT Data Control Jumpers (JP5.3/4, JP5.5/6)
JP5.3/4 JP5.5/6 jumpers used together direction well enable disable drivers driving VID_OUT data bus. Table shows results different combinations JP5.3/4 JP5.5/6 jumpers.
Blackfin EZ-Extender Manual
2-11
Jumpers
Table 2-6. Jumper Combinations
JP5.3/4 Uninstalled Uninstalled Installed Installed JP5.5/6 Uninstalled Installed Uninstalled Installed VID_OUT Status
VID_OUT, PPI1 state JP9.2/4/6 PPI1 PPI0 PPI0
driven; PPI0 depends
drives VID_OUT drives VID_OUT
drives VID_OUT, VID_OUT drives PPI1 (loopback mode)
PPI0_SYNC1 Direction Setup Jumper (JP6.1/3/5)
direction PPI0_SYNC1 signal either fixed programmed, depending state general-purpose flag. Table shows direction PPI0_SYNC1. Table 2-7. Setting Direction PPI0_SYNC1 (JP6.1/3/5)
Jumper Location
JP6.1/3 JP6.3/5
PPI0_SYNC1 Direction Controlled flag Input processor Output from processor
Uninstalled
PPI0_SYNC2 Direction Setup Jumper (JP6.2/4/6)
direction PPI0_SYNC2 signal either fixed programmed, depending state general-purpose flag. Table shows direction PPI0_SYNC2.
2-12
Blackfin EZ-Extender Manual
EZ-Extender Hardware Reference
Table 2-8. Setting Direction PPI0_SYNC2 (JP6.2/4/6)
Jumper Location
JP6.2/4 JP6.4/6
PPI0_SYNC2 Direction Controlled flag Input processor Output from processor
Uninstalled
Enable Jumper (JP7.1/2)
When JP7.1/2 jumper installed, SPORT signals routed SPORT communication protocol mode. accomplish this, receive transmit clocks processor routed driven output clock AD1836A. same done frame sync signals.
SPORT Data Connection Jumpers (JP7.3/4, JP7.5/6)
JP7.3/4 JP7.5/6 jumpers connect data output pins (ASDATA1 ASDATA2) audio codec primary secondary SPORT data input pins processor. audio codec driving these pins-with help JP7.3/4 JP7.5/6 jumpers, processor's pins reused when audio codec used.
VID_OUT Sync Source Select Jumpers (JP8.1/3/5, JP8.2/4/6)
source frame sync signals depends port driving VID_OUT bus. When using PPI0, place jumpers JP8.1/3 JP8.2/4. When using PPI1, place jumpers JP8.3/5 JP8.4/6.
VID_OUT Sync Enable Jumper (JP8.7/8)
enable VID_OUT frame sync signals, install JP8.7/8 jumper.
Blackfin EZ-Extender Manual
2-13
Jumpers
AV_RESET Source Jumper (JP9.1/3/5)
source reset EZ-Extender controlled either flag system reset, latter also resetting Blackfin processor (see Table 2-9). Table 2-9. Jumper Reset Sources
Jumper Location
JP9.1/3 JP9.3/5
Reset Source Flag multiplexed with PPI1_D11 System reset generator reset
Uninstalled
PPI0_D Direction Setup Jumper (JP9.2/4/6)
direction PPI0_D[15:0] signal fixed direction programmed, depending state general-purpose flag. Table 2-10 shows direction PPI0_D[15:0]. Table 2-10. Setting Direction PPI0_D[15:0] (JP9.2/4/6)
Jumper Location
JP9.2/4 JP9.4/6
PPI0_D[15:0] Direction Controlled flag Input processor Output from processor
Uninstalled
Audio Loopback Jumpers (JP10.1/2, JP10.3/4)
JP10.1/2 JP10.3/4 jumpers loop back audio input output test purposes should installed.
2-14
Blackfin EZ-Extender Manual
BILL MATERIALS
bill materials corresponds board schematics page B-1. Please check latest schematics Analog Devices website,
Blackfin EZ-Extender Manual
Reference Designator C1,C4,C7-8,C10-15,C17, 0603YC104KAT2A C102,C113-114,C116, C140,C142 C18,C20-21,C28,C31,C35, C2-3,C6,C16,C25,C29,C36, KEMET C27,C39 C42,C45,C59,C79-80 PANASONIC PANASONIC ECJ-1VB1C105K ECJ-2FF1A106Z 08055C823JAT2A 06035A331JAT2A PANASONIC ECJ-1VB1H222K Manufacturer Part Number C71,C74,C82-83,C127-128, PANASONIC C141 C73,C85,C101,C112, C120-121 ECJ-1VC1H121J 08053C224FAT C77,C91-92,C97,C105-106, PANASONIC C109 C84,C88-90,C122-123 PANASONIC ECJ-1VC1H101J ECJ-1VC1H681J
Ref.
Description
0.1UF 10%603
2200pF 0603
330PF 0603
0.01UF 0603
0603
10UF +80/-20% 0805
82NF
120PF 0603
0.22uF CERM
100PF 0603
Blackfin EZ-Extender Manual
680pF 0603
Ref. C87,C94-96,C125-126 C9,C24,C72,C86,C93,C100, PANASONIC C103 CT1-4,CT12-13 TAJB106K016R ECJ-1VC1H102J PANASONIC ECJ-1VC1H221J
Description
Reference Designator
Manufacturer
Part Number
220PF 0603
0.001UF 0603
10uF TANT CT5-11,CT14-16 DIG01
10uF CAP002 ELEC
PCE3062TR-ND
Blackfin EZ-Extender Manual
ANALOG DEVICES AD1580BRT FER1-3,FER9 DIGIKEY 240-1019-1-ND FER4-8 MURATA BLM11A601SPT J1-3 SAMTEC SFC-145-T2-F-D-A SAMTEC SSW-116-02-F-D-RA FOXCONN JA33331-R55
10MA AD1580BRT SOT23D 1.2V-SHUNT-REF
100MHZ 500MA 1206 0.70 BEAD
100MHZ 200MA 0.50 BEAD
0.05 45X2 CON019 SOCKET
16X2 IDC16X2RASOC SOCKET
3.5MM 5xAUDIO_JACK CON035 3.5MM AUDIO JACK
Bill Materials
Reference Designator SAMTEC SSW-113-02-F-D-RA Manufacturer Part Number SWITCHCRAFT PJRAS3X2S01 JP1,JP5-7,JP9 JP10 DIGI-KEY SAMTEC TSM-103-01-T-DV S2011-02-ND DIGI-KEY S1011-03-ND SAMTEC TSM-113-01-T-DV JP4,JP8 L1-3,L7-9 L4-6 LED1 SAMTEC MURATA MURATA PANASONIC TSM-104-01-T-DV LQG21NR68K10T1 LQG21N2R2K10 LN1361C P1-3 SAMTEC TFC-145-32-F-D
Ref.
Description
13x2RA IDC13x2_F_RA 13x2 FEMALE
CON024
IDC3X2_SMT
IDC2X2 GOLD
IDC3X1 GOLD
13X2 IDC13X2_M_SMT
IDC4X2_M_SMT
0.68UH 0.72
2.2UH 0.63
GREEN-SMT LED001 GULL-WING
Blackfin EZ-Extender Manual
0.05 45x2 CON018 HEADER
Ref. SULLINS PTC14DBAN
Description
Reference Designator
Manufacturer
Part Number
14x2RA IDC14x2_M_RA 14X2 MALE HIROSE DF9-31P-1V
FPDI 31PIN CON034 FLAT PANEL DISP CONNECTOR R11-12,R16-17,R21-22, R26-31 R114 R13-14,R18-19,R23-24 R15,R20,R25,R111,R115, R130 R2-4,R10,R32,R37,R44-48, R39-40 YAGEO PHYCOMP DIGI-KEY
1.5K 100MW
CR21-1501F-T 9T06031A75R0FBHFT
Blackfin EZ-Extender Manual
CR32-681J-T 9C06031A1001JLHFT 9C06031A0R00JLHFT VISHAY CRCW0603103JRT1 DIGIKEY DIGIKEY VISHAY PANASONIC 311-147KCCT-ND 311-76.8KCCT-ND CRCW0603104JRT1 ERJ-8ENF1500V
75.0 1/10W 0603
1/8W 1206
1/10W 0603
1/10W 0603
1/10W 0603
147K 100MW
76.8K 100MW
100K 1/10W 0603
Bill Materials
1/8W 1206
Reference Designator R49,R52 R5,R8,R33,R68,R142-145 R50, R146-148 R53,R55 R61-63,R67,R72-73,R76-77, DIGI-KEY R105 R64,R70,R106,R110 R65,R69,R127,R129 DIGI-KEY DIGI-KEY VISHAY/DALE VISHAY DIG01 311-33.0HTR-ND CRCW0603220JRT1 CRCW0805220JRT1 311-5.76KHTR-ND CR21-330JTR PANASONIC ERJ-2GEJ122X Manufacturer Part Number 311-237HTR-ND 311-750KHTR-ND R71,R78-80,R112-113 DIGI-KEY 311-2.74KHTR-ND R74,R84-85,R88,R117-118 R75,R83,R86-87,R89, R99-101 R81,R91-92,R95,R124-125 DIGI-KEY DIGI-KEY 311-1.65KHTR-ND 311-5.49KHTR-ND DIGI-KEY 311-3.32KHTR-ND R82,R90,R93-94,R123,R126 DIGI-KEY 311-11KHTR-ND
Ref.
Description
1.2K 1/16W
100MW
1/10W 0603
1/10W 0603
1/10W
5.76K 1/10W 0603
1/10W 0603
750K 1/10W 0603
2.74K 1/10W 0603
1.65K 1/10W 0603
5.49K 1/10W 0603
3.32K 1/10W 0603
Blackfin EZ-Extender Manual
1/10W 0603
Ref. R96-97,R108-109,R137-138 DIGI-KEY 311-49.9KHTR-ND
Description
Reference Designator
Manufacturer
Part Number
49.9K 1/10W 0603 R98,R102-104,R133,R136 RN1-4 FAIRCHILD EPSON DIGIKEY DIGI-KEY 311-604HTR-ND 744C083220JCT-ND SG-8002CA 74LVTH16244MTD
1/10W 0603
125MW RNS001
27MHZ OSC003
Blackfin EZ-Extender Manual
U11,U14,U16 FAIRCHILD 74LVTH16245MTD U12-13,U15,U17,U19, U29-30 SN74LVC1G125DBVR DIG01 SG-8002CA-PCC-ND ANALOG DEVICES ADV7183BKSTZ U20-23,U25-28 ANALOG DEVICES AD8606AR
74LVTH16244MTD TSSOP48 16BIT-BUFFER-DRIVER
74LVTH16245MTD TSSOP48 16BIT-BUFFER-TXRX
SN74LVC1G125 SOT23-5 SINGLE-3STATE-BUFFER
12.288MHZ OSC003 TS201/21262
ADV7183BKSTZ LQFP80 VID-DECODER
AD8606AR SOIC8 OPAMP
Bill Materials
Reference Designator ANALOG DEVICES AD1836AAS Manufacturer Part Number U3-5 ANALOG DEVICES AD8061ART-REEL SN74LVC1G32DBVR ANALOG DEVICES ADV7179KCP MILL-MAX 614-93-308-31-007 SN74AHC1G00DBVR ANALOG DEVICES ADP3336ARM-REEL
Ref.
Description
AD1836AASMQFP52 MULTI-CHANNEL- 96KHZ-CODEC
AD8061ART SOT23-5 300MHZ-AMP
SN74LVC1G32 SOT23-5 SINGLE-2 INPUT GATE
ADV7179 LFCSP40 VIDEO ENCODER
TH-TH CARRIER SOCKETED
SN74AHC1G00 SOT23-5 SINGLE-2-INPUT-NAND
Blackfin EZ-Extender Manual
ADP3336ARM MSOP8 500MA REGULATOR
Blackfin EZ-Extender Schematic
Populate Manual Jumper Settings
ANALOG DEVICES
Title Size Board
12-1-2004_18:50
Cotton Road Nashua, 03063 1-800-ANALOGD
Blackfin EZ-Extender TITLE A0193-2004
Sheet
Date
EXPANSION INTERFACE (TYPE
Expanison Connector Bottom Board Board P1_[5:86] P1_40 P1_42 P1_44 P1_46 P1_48 P1_50 P1_52 P1_54 P1_56 P1_58 P1_60 P1_62 P1_64 P1_66 P1_68 P1_70 PPI0_D0 PPI0_D2 P1_76 P1_78 P1_80 P1_82 P1_84 P1_86 PPI0_D0 PPI0_D2 P1_76 P1_78 P1_80 P1_82 P1_84 P1_86 P1_40 P1_42 P1_44 P1_46 P1_48 P1_50 P1_52 P1_54 P1_56 P1_58 P1_60 P1_62 P1_64 P1_66 P1_68 P1_70 P1_6 P1_8 P1_10 P1_12 P1_14 P1_16 P1_18 P1_20 P1_22 P1_24 P1_26 P1_28 P1_30 P1_32 P1_34 P1_36 P1_6 P1_8 P1_10 P1_12 P1_14 P1_16 P1_18 P1_20 P1_22 P1_24 P1_26 P1_28 P1_30 P1_32 P1_34 P1_36 45X2 CON019 P1_77 P1_79 P1_81 P1_83 P1_85 PPI0_D1 PPI0_D3 P2_77 P2_79 P2_81 P2_83 P2_85 P1_39 P1_41 P1_43 P1_45 P1_47 P1_49 P1_51 P1_53 P1_55 P1_57 P1_59 P1_61 P1_63 P1_65 P1_67 P1_69 PPI0_CLK FLAG_SDA P2_59 P2_61 P2_63 P2_65 P2_67 P2_69 P2_71 P2_73 P1_5 P1_7 P1_9 P1_11 P1_13 P1_15 P1_17 P1_19 P1_21 P2_23 P1_23 P1_25 P1_27 P1_29 P1_31 P1_33 P1_35 DR0SEC DR0PRI RFS0 RSCLK0 PPI0_D4 PPI0_D6 PPI0_D8 PPI0_D10 PPI0_D12 PPI0_D14 P2_55 R149 0603 PPI0_SYNC1 P2_27 P2_29 P2_31 P2_33 P2_15 P2_17 P2_19 P2_21 P2_23 P2_11 P2_5 P2_7 45X2 CON018 Bottom Board
3.3V
Expanison Connector Board P2_[5:86] P2_6 P2_8 MOSI MISO MOSI MISO P2_6 P2_8 P2_16 P2_18 P2_20 P2_22 PPI0_SYNC2 P2_26 P2_28 P2_30 P2_32 P2_34 DT0SEC DT0PRI TFS0 TSCLK0 PPI0_D5 PPI0_D7 PPI0_D9 PPI0_D11 PPI0_D13 PPI0_D15 SNAPSHOT_FODD_SSEL DT0SEC DT0PRI TFS0 TSCLK0 PPI0_D5 PPI0_D7 PPI0_D9 PPI0_D11 PPI0_D13 PPI0_D15 PPI0_SYNC2 P2_26 P2_28 P2_30 P2_32 P2_34 P2_16 P2_18 P2_20 P2_22 P2_60 P2_62 P2_64 P2_66 P2_68 P2_70 P2_72 P2_74 FLAG_SCL_DIR_CTRL P2_60 P2_62 P2_64 P2_66 P2_68 P2_70 P2_72 P2_74 P2_78 P2_80 P2_82 P2_84 P2_86 P2_78 P2_80 P2_82 P2_84 P2_86 45X2 CON019 P2_77 P2_79 P2_81 P2_83 P2_85 P2_59 P2_61 P2_63 P2_65 P2_67 P2_69 P2_71 P2_73 P2_55 FLAG_SDA PPI0_D4 PPI0_D6 PPI0_D8 PPI0_D10 PPI0_D12 PPI0_D14 P2_27 P2_29 P2_31 P2_33 DR0SEC DR0PRI RFS0 RSCLK0 P2_15 P2_17 P2_19 P2_21 P2_23 PPI0_SYNC1 P2_11 P2_5 P2_7
P1_5 P1_7 P1_9 P1_11 P1_13 P1_15 P1_17 P1_19 P1_21 P1_23 P1_25 P1_27 P1_29 P1_31
P1_33 P1_35
P1_39 P1_41 P1_43 P1_45 P1_47 P1_49 P1_51 P1_53 P1_55 P1_57 P1_59 P1_61 P1_63 P1_65 P1_67 P1_69
PPI0_D1
45X2 CON018
PPI0_D3 P1_77 P1_79 P1_81 P1_83 P1_85
PPI0_D[15:0] 3.3V
Populate Manual Jumper Settings
10UF 0805 0.1UF
10UF 0805
0.1UF
ANALOG DEVICES
Title Size Board
2-9-2005_16:10
Cotton Road Nashua, 03063 1-800-ANALOGD
Blackfin EZ-Extender EXPANSION INTERFACE A0193-2004
Sheet
Date
EXPANSION INTERFACE (TYPE
3.3V
Bottom Board
Expanison Connector Board PPI1_D[15:0] P3_[1:90] PPI1_D1 P3_5 P3_7 PPI1_D3 PPI1_D5 PPI1_D7 PPI1_D9 PPI1_D11 PPI1_D13 PPI1_D15 PPI1_CLK P3_29 P3_31 P3_45 P3_47 P3_49 P3_51 P3_53 P3_55 P3_57 P3_59 P3_61 P3_63 P3_67 P3_69 P3_71 P3_73 P3_89 45X2 CON018 P3_90 P3_90 P3_68 P3_70 P3_72 P3_74 P3_76 P3_78 P3_80 P3_82 P3_84 P3_86 P3_68 P3_70 P3_72 P3_74 P3_76 P3_78 P3_80 P3_82 P3_84 P3_86 P3_46 P3_48 P3_50 P3_52 P3_54 P3_56 P3_58 P3_60 P3_62 P3_64 P3_46 P3_48 P3_50 P3_52 P3_54 P3_56 P3_58 P3_60 P3_62 P3_64 P3_42 P3_42 P3_32 P3_34 P3_36 P3_38 PPI1_FS2 P3_32 P3_34 P3_36 P3_38 P3_28 RESET P3_28 P3_6 P3_8 PPI1_D2 PPI1_D4 PPI1_D6 PPI1_D8 PPI1_D10 PPI1_D12 PPI1_D14 PPI1_D2 PPI1_D4 PPI1_D6 PPI1_D8 PPI1_D10 PPI1_D12 PPI1_D14 P3_6 P3_8 PPI1_D0 PPI1_D0 45X2 CON019 P3_89 P3_67 P3_69 P3_71 P3_73 P3_75 P3_77 P3_79 P3_81 P3_83 P3_85 IDC13X2_M_SMT 13X2 Jumpers P3_45 P3_47 P3_49 P3_51 P3_53 P3_55 P3_57 P3_59 P3_61 P3_63 DEC_DATA_OE SNAPSHOT_FODD 0603 P3_29 P3_31 P3_33 P3_35 P3_37 P3_39 PPI1_FS1 PPI1_FS1 3.3V FLAG_SDA PPI1_D2 PWDN VDEC_HS VDEC_VS VENC_HREF VENC_VSYNC SNAPSHOT_FODD_SSEL FLAG_SCL_DIR_CTRL PPI1_D3 PPI1_D10 VID_IN_SYNC1_HREF VID_IN_SYNC2_VSYNC ADSP-BF537 EZ-KIT Lite 3.3V P3_5 P3_7 PPI1_D3 PPI1_D5 PPI1_D7 PPI1_D9 PPI1_D11 PPI1_D13 PPI1_D15 PPI1_CLK R114 1206 PPI1_D1 POWER LED1 GREEN-SMT LED001
P3_33 P3_35 P3_37 P3_39
P3_75 P3_77 P3_79 P3_81 P3_83 P3_85
3.3V
Populate Manual Jumper Settings
10UF 0805
0.1UF
10UF 0805
0.1UF
ANALOG DEVICES
Title Size Board
1-6-2005_16:35
Cotton Road Nashua, 03063 1-800-ANALOGD
Blackfin EZ-Extender EXPANSION INTERFACE A0193-2004
Sheet
Date
PPI0_D[15:0]
VID_IN_D[15:0] VID_IN_D0 VID_IN_D1 VID_IN_D2 VID_IN_D3 VID_IN_D4 VID_IN_D5 VID_IN_D6 VID_IN_D7 VID_IN_D8 VID_IN_D9 VID_IN_D10 VID_IN_D11 VID_IN_D12 VID_IN_D13 VID_IN_D14 T/~R1 T/~R2 74LVTH16245MTD TSSOP48 PPI0_HI_EN RNS001 PPI0_D3 RNS001 PPI0_D4 PPI0_D4 PPI0_D5 PPI0_D5 PPI0_D6 PPI0_D6 PPI0_D7 PPI0_D7 PPI0_D8 RNS001 PPI0_D8 PPI0_D9 PPI0_D9 PPI0_D10 PPI0_D10 PPI0_D11 PPI0_D11 PPI0_D12 PPI0_D13 PPI0_D14 RNS001 PPI0_D12 PPI0_D15 PPI0_D13 PPI0_D14 PPI0_D15 PPI0_EN VID_IN_DIR_CTRL 74LVTH16244MTD TSSOP48 VID_OUT_D8 VID_OUT_D9 VID_OUT_D10 VID_OUT_D11 VID_OUT_D12 VID_OUT_D13 VID_OUT_D14 VID_OUT_D15 PPI0_D0 PPI0_D1 PPI0_D2 PPI0_D3 PPI0_D0 PPI0_D1 PPI0_D2 VID_OUT_D0 VID_OUT_D1 VID_OUT_D2 VID_OUT_D3 VID_OUT_D4 VID_OUT_D5 VID_OUT_D6 VID_OUT_D7 VID_OUT_D[15:0]
VID_IN_D15
PPI1_D[15:0]
3.3V 3.3V 3.3V PPI1_D0 PPI1_D1 PPI1_D2 PPI1_D3 PPI1_D4 PPI1_D5 0603 PPI1_D11 AV_RESET RESET IDC3X2_SMT Jumpers FLAG_SCL_DIR_CTRL VID_IN_DIR_CTRL 0603 0603 0603 0603 PPI1_D6 PPI1_D7 PPI1_EN T/~R1 T/~R2 74LVTH16245MTD TSSOP48 VID_OUT_D0 VID_OUT_D1 VID_OUT_D2 VID_OUT_D3 VID_OUT_D4 VID_OUT_D5 VID_OUT_D6 VID_OUT_D7 VID_OUT_D8 VID_OUT_D9 VID_OUT_D10 VID_OUT_D11 VID_OUT_D12 VID_OUT_D13 VID_OUT_D14 VID_OUT_D15
PPI1_D8 PPI0_HI_EN PPI0_EN PPI1_EN PPI1_D9 PPI1_D10 PPI1_D11 PPI1_D12 PPI1_D13 PPI1_D14 PPI1_D15
IDC3X2_SMT
PPI0_EN
3.3V
3.3V
3.3V
Populate Manual Jumper Settings
0.1UF
0.1UF
0.1UF
0.1UF
0.1UF
0.1UF
ANALOG DEVICES
Title Size Board
12-1-2004_14:50
Cotton Road Nashua, 03063 1-800-ANALOGD
Blackfin EZ-Extender DATA ROUTING A0193-2004
Sheet
74LVTH16245MTD
SN74ALVTH16244
SN74ALVTH16244
Date
Video Frame Sync Setup
VID_IN_SYNC1_HREF 3.3V 27MHZ_CLK IDC3X2_SMT Jumpers R148 0603 VID_IN_SYNC1_DIR_CTL VID_IN_SYNC2_DIR_CTL PPI0_SYNC2 FLAG_SCL_DIR_CTRL 0603 0603 0603 PPI0_SYNC1 3.3V
Clock Setup
VID_IN_SYNC2_VSYNC
OE/NC SOCKET DIP8SOC
VDEC_CLKOUT PIXEL_CLK
EXT_VID_CLK
T/~R1 T/~R2 74LVTH16245MTD TSSOP48
VID_IN_SYNC1_DIR_CTL VID_IN_SYNC2_DIR_CTL
SN74LVC1G125 SOT23-5
IDC4X2_M_SMT Jumpers 3.3V TP10
0603 0603 PPI0_CLK
SN74LVC1G125 SOT23-5
VID_OUT_SYNC_EN R146 0603 VID_OUT_SYNC1_HREF
VID_OUT_SYNC_EN R147 0603 VID_OUT_SYNC2_VSYNC
VID_OUT_SYNC1
VID_OUT_SYNC2
SN74LVC1G125 SOT23-5
SN74LVC1G125 SOT23-5 3.3V 3.3V TP11 TP12
EXT_VID_CLK PPI0_SYNC2 VID_OUT_SYNC2 PPI1_FS2
0603
Video Frame Sync Setup
0603 PPI1_CLK
PPI0_SYNC1 VID_OUT_SYNC1 PPI1_FS1 VID_OUT_SYNC_EN
SN74LVC1G125 SOT23-5
IDC4X2_M_SMT Jumpers
3.3V
3.3V
3.3V
3.3V
3.3V
3.3V
Populate Manual Jumper Settings
0.1UF
0.1UF
0.1UF
0.1UF
0.1UF
0.1UF
0.1UF
ANALOG DEVICES
Title Size Board
1-18-2005_9:12
Cotton Road Nashua, 03063 1-800-ANALOGD
Blackfin EZ-Extender FS/CLK CONFIG A0193-2004
Sheet
SN74LVC1G125 SN74LVC1G125 SN74LVC1G125
74LVTH16245MTD
SN74LVC1G125
Date
CONN_SUPPLY
Micron Interface
VID_IN_D[15:0]
Kodak Interface
VID_IN_D1 VID_IN_D3 VID_IN_D5 VID_IN_D7 VID_IN_D9 AV_RESET EXT_VID_CLK IDC13X2_F_RA 13X2RA PIXEL_CLK VID_IN_SYNC2_VSYNC VID_IN_SYNC1_HREF VID_IN_D0 VID_IN_D2 VID_IN_D4 VID_IN_D6 VID_IN_D8 3.3V
Micron Interface
CONN_SUPPLY TP13
OmniVision Interface
IDC3X1 Jumper
0.1UF
10UF 0805
Flat Panal Display Interface
CONN_SUPPLY CONN_SUPPLY
VID_IN_D0 PWDN EXT_VID_CLK EXCLK VID_IN_D8 VID_IN_D10 VID_IN_D12 VID_IN_D14 IDC16X2RASOC 16X2 RESET FODD HREF VSYNC PCLK VID_IN_D9 VID_IN_D11 VID_IN_D13 VID_IN_D15 SNAPSHOT_FODD VID_IN_D1 VID_IN_D3 VID_IN_D5 VID_IN_D7 SN74AHC1G00 SOT23-5 AV_RESET VCC1 VCC2
VID_OUT_D0 VID_OUT_D1 VID_OUT_D2 VID_OUT_D3 VID_OUT_D4 VID_OUT_D5 VID_OUT_D6 VID_OUT_D7 VID_OUT_D8 VID_OUT_D9 VID_OUT_D10 VID_OUT_D[15:0] EXT_VID_CLK VID_OUT_SYNC1_HREF VID_OUT_SYNC2_VSYNC
VID_IN_D2 VID_IN_D4 VID_IN_D6 PWDN
VID_IN_SYNC1_HREF VID_IN_SYNC2_VSYNC PIXEL_CLK
OmniVision Interface
CONN_SUPPLY VID_OUT_D11 VID_OUT_D12 VID_OUT_D13 VID_OUT_D14 VID_OUT_D15 0603 0603
CONN_SUPPLY ENAB
VID_IN_SYNC1_HREF PIXEL_CLK VID_IN_D0 VID_IN_D2 VID_IN_D4 VID_IN_D6 VID_IN_D8 VID_IN_D10 IDC14X2_M_RA 14X2RA RESET PWDN EXT_SYNC PWDN PPI0_D15 AV_RESET 0.1UF VID_IN_D1 VID_IN_D3 VID_IN_D5 VID_IN_D7 VID_IN_D9 3.3V VID_IN_D11 SNAPSHOT SNAPSHOT_FODD VID_IN_SYNC2_VSYNC EXT_VID_CLK GND1 GND2 GND3 GND4 GND5
0603 0603 0603
Kodak Interface
CON034
31PIN
Populate Manual Jumper Settings
ANALOG DEVICES
Title Size Board
1-6-2005_16:35
Cotton Road Nashua, 03063 1-800-ANALOGD
Blackfin EZ-Extender PPI0 SETUP A0193-2004
Sheet
Note: numbers look swapped this connector This just industry standard numbering male connector footprint connecting board correct. SN74AHC1G00
Date
DAC_C
DAC_B
VIDEO_AVIN1 VIDEO_AVIN4 VIDEO_AVIN5
VIDEO_DAC_A VIDEO_DAC_C VIDEO_DAC_B
DAC_A
Composite Video Component Video Differential Component Video Video CVSB
CVSB
IDC3X2_SMT
(WHITE) (RED)
AVIN5
AVIN4
AVIN1
0603
VIDEO_DAC_A
0.68UH 2.2UH 0.68UH AD8061ART SOT23-5 75.0 0603
CON024
VIDEO ENCODER
VAA1 VAA2 VAA3 VAA4
3.3V 0603
FER4
75.0 0603
330PF 0603
330PF 0603
75.0 0603
0603
0.1UF
0.1UF
1.2K AGND2
VAA5 VID_OUT_D[7:0] VID_OUT_D7 VID_OUT_D6 VID_OUT_D5 VID_OUT_D4 VID_OUT_D3 VID_OUT_D2 VID_OUT_D1 VID_OUT_D0 DAC_A DAC_B DAC_C HSYNC 27MHZ_CLK CLOCK FIELD/VSYNC BLANK AV_RESET 3.3V ALSB GND2 SDATA GND3 SCLOCK GND4 100K 0603 SCRESET/RTC GND8 GND9 TTXREQ GND10 ADV7179 LFCSP40 100K 0603 GND5 GND6 GND7 RESET GND1 COMP VREF RSET
0603
VENC_HREF VENC_VSYNC 0.68UH 2.2UH 0.68UH AGND2 0603 1206 AD1580BRT SOT23D 10MA 75.0 0603 330PF 0603 330PF 0603 75.0 0603 0603 AD8061ART SOT23-5 75.0 0603 CON024 VIDEO_DAC_B
VIDEO_DAC_C 0.68UH 2.2UH 0.68UH AD8061ART SOT23-5 75.0 0603 CON024
3.3V
75.0 0603
330PF 0603
330PF 0603
75.0 0603
0603
Populate Manual Jumper Settings
0.01UF 0603 0.01UF 0603 0.1UF 0.1UF 0.1UF 0.1UF COPPER 0.1UF 0.01UF 0603 0.1UF 0.1UF 0.1UF 0.01UF 0603 AGND2
ANALOG DEVICES
Title Size Board
1-6-2005_16:35
Cotton Road Nashua, 03063 1-800-ANALOGD
ADV7179
AGND2
AGND2 AD8061
AGND2 AD8061
AGND2 AD8061
Blackfin EZ-Extender VIDEO ENCODER (OUT) A0193-2004
Sheet
Date
3.3V 3.3V
AVIN1 Composite Video Differential Component Video Video CVBS
AVIN4 CVBS
AVIN5 CVBS 0603 0603 27MHZ OSC003 0603 27MHZ_CLK 0603 0603 0603
VIDEO DECODER
XTAL XTAL1 ALSB SCLK PVDD_ADV7183 SN74LVC1G32 SOT23-5 VID_IN_D7 VID_IN_D6 VID_IN_D5 VID_IN_D4 VID_IN_D3 VID_IN_D2 VID_IN_D1 VID_IN_D0 0603 0603 VDEC_CLKOUT VID_IN_D[7:0]
AV_RESET
RESET PWRDN
CON024
0603 VIDEO_AVIN1 0.1UF
NC[ISO]
AVIN1
AIN1 AIN7
CON024
AIN2 AIN8
0603 VIDEO_AVIN4
0.1UF
AVIN4
LLC1 AIN3 AIN9 LLC2 NC[LLCREF] ELPF AIN4 AIN10 AIN5 AIN11 FIELD NC[VREF] NC[HREF] AIN6 AIN12 NC[CLKIN] NC[AFF] REFOUT SFL[HFF] NC[AEF] NC[DV] CAPY1 CAPY2 NC[RD]
0.01UF 0603 1.5K 82NF
CON024
0603 VIDEO_AVIN5 0.1UF
VDEC_HS VDEC_VS VDEC_FIELD VDEC_VREF VDEC_HREF
AVIN5
75.0 0603
75.0 0603
75.0 0603 10UF 0.1UF 10UF 0.1UF
DEC_DATA_OE
AGND2
AGND2 10UF 0.1UF 0.001UF 0603
CAPC1 CAPC2
NC[GPO3] NC[GPO2] NC[GPO1]
DVDD_ADV7183 FER3 1206 0603 OUT1 OUT2 OUT3 ADP3336ARM MSOP8 1.8V 3.3V 3.3V 3.3V 1.8V
0.1UF
0.1UF
NC[GPO0] 10UF 0.1UF 0.001UF 0603
AVDD
DVDD1 DVDD2 DVDD3
AGND2
AGND2 0.1UF 0.1UF
PVDD
DVDDIO1 DVDDIO2
76.8K
0603
AGND1 AGND2 AGND3 AGND4 AGND5 NC[AGND6] DGND1 DGND2 DGND3 DGND4 DGND5 0603
1.8V
3.3V AGND2 FER2 1206 AGND2
147K
ADV7183BKSTZ LQFP80
FER1 1206 3.3V 3.3V 3.3V DVDD_ADV7183 0.1UF 0.01UF 0603 0.1UF 0.01UF 0603 PVDD_ADV7183
Populate Manual Jumper Settings
0.1UF
0.01UF 0603
0.1UF
0.1UF
0.01UF 0603
0.01UF 0603
0.1UF
0.1UF
0.1UF
ANALOG DEVICES
Title Size Board
1-6-2005_16:35
Cotton Road Nashua, 03063 1-800-ANALOGD
AGND2
Blackfin EZ-Extender VIDEO DECODER (IN) A0193-2004
Sheet
27MHZ
SN74LVC1G32
ADV7183
Date
I2S_EN I2S_EN RFS0 R144 0603 TFS0 RSCLK0 R145 0603 TSCLK0 3.3V
SN74LVC1G125 SOT23-5
SN74LVC1G125 SOT23-5
0603
0603 AD1836_CLK
OUT1 (BLUE) (BLACK) OUT2 (LIME) (YELLOW) OUT3 (PINK)
3.3V
12.288MHZ OSC003
AUDIO CODEC
3.3V R141 0603 I2S_EN DR0PRI DR0SEC IDC3X2_SMT Jumpers R142 0603 RFS0 RSCLK0 R143 0603 AD1836_CLK R107 0603 FER9 1206 3.3V
5V140
ASDATA1 ASDATA2 ALRCLK ABCLK
A5V115 A5V2
ADC1_LEFT OUT1L+ OUT1L8 OUT1L+ OUT1L-
DAC1 LEFT
ADC1_RIGHT
(BLACK)
OUT1R+
OUT1R+ OUT1R-
OUT1R45 MCLK OUT2L+ SNAPSHOT_FODD_SSEL MOSI MISO CLATCH CCLK CDATA COUT OUT2L6
DAC1 RIGHT DAC2 LEFT DAC2 RIGHT DAC3 LEFT DAC3 RIGHT
ADC2_LEFT
OUT2L+ OUT2L-
ADC2_RIGHT
(YELLOW)
OUT2R+
OUT2R+ OUT2R-
DAC1_LEFT
OUT2R-
OUT1 (BLUE)
ADC1 LEFT ADC1 RIGHT
IN1L+ IN1L-
IN1L+ IN1L-
OUT3L+ OUT3L-
OUT3L+ OUT3L-
DAC1_RIGHT
DAC2_LEFT IN1R+ IN1R18 IN1R+ IN1ROUT3R+ OUT3R+ OUT3R-
OUT3R-
OUT2 (LIME)
DAC2_RIGHT IN2L+/CL2/CL2 IN2L-/CL1/CL1 NC/IN2L1/IN2L+ NC/IN2L2/IN2L38 DSDATA1 DSDATA2 DSDATA3 DLRCLK DBCLK DT0PRI DT0SEC DAC3_LEFT TFS0 TSCLK0 R135 0603 IDC2X2 AD8606AR SOIC8 14AGND1 28AGND2 29AGND3 AGND4 CT12 10UF C131 0.1UF CT13 10UF C132 0.1UF R130 0603 R111 0603 AGND AD1836_VREF DAC3_RIGHT
JP10 CON035 5XAUDIO_JACK
ADC2 LEFT ADC2 RIGHT
IN2L1 IN2L2
OUT3 (PINK)
IN2R2 IN2R1
NC/IN2R2/IN2R25 NC/IN2R1/IN2R+ IN2R-/CR1/CR1 IN2R+/CR2/CR2
FILTR FILTD
AV_RESET
AD1836AAS MQFP52
52GND1 GND2
PD/RST
0.001UF 0603
C100 0.001UF 0603
C103 0.001UF 0603
C111 0.001UF 0603
AD8606AR SOIC8 R115 0603
AGND
AGND
3.3V
3.3V
3.3V
3.3V
Populate Manual Jumper Settings
C144 0.1UF
C145 0.1UF
0.1UF
C110 0.01UF 0603
C124 0.1UF
0.1UF
C115 0.1UF
C130 0.1UF
COPPER MSC_COPPER
C120 0.22UF
ANALOG DEVICES
Title Size Board
11-26-2004_10:48
Cotton Road Nashua, 03063 1-800-ANALOGD
Blackfin EZ-Extender AUDIO A0193-2004
Sheet
AGND SN74LVC1G125 SN74LVC1G125 12.288MHZ
AD1836
AGND
AGND AD8606
Date
R100 5.49K 0603 0603 OUT1RR92 3.32K 0603
C106 100PF 0603
C107 330PF 0603
DAC1 RIGHT
5.49K 0603 OUT1R+ 680PF 0603 1.65K 0603 AD8606AR SOIC8
R102 0603
10UF CAP002 DAC1_RIGHT
2.74K 0603
220PF 0603
C113 2200PF 0603
R109 49.9K 0603
AGND
5.49K 0603 0603 OUT1LR91 3.32K 0603
C105 100PF 0603
C104 330PF 0603
DAC1 LEFT
5.49K 0603 OUT1L+ 680PF 0603 1.65K 0603
AD8606AR SOIC8 R104 0603
2.74K 0603 AD1836_VREF 220PF 0603
10UF CAP002 DAC1_LEFT
C116 2200PF 0603
R108 49.9K 0603
AGND
Populate Manual Jumper Settings
C112 0.22UF
ANALOG DEVICES
Title Size Board
12-1-2004_18:50
Cotton Road Nashua, 03063 1-800-ANALOGD
Blackfin EZ-Extender AUDIO OUT(CH1) A0193-2004
Sheet
AGND AD8606
Date
R132 5.49K 0603 R126 0603 OUT2RR125 3.32K 0603 OUT3RC136 100PF 0603 0603 R101 5.49K 0603 3.32K 0603 C109 100PF 0603
C137 330PF 0603
C108 330PF 0603
DAC2 RIGHT
R119 5.49K 0603 OUT2R+ C123 680PF 0603 R118 1.65K 0603
DAC3 RIGHT
R133 0603 5.49K 0603 OUT3R+ DAC2_RIGHT 680PF 0603 1.65K 0603 AD8606AR SOIC8
AD8606AR SOIC8
CT15 10UF CAP002
R103 0603
10UF CAP002 DAC3_RIGHT
R113 2.74K 0603 AD1836_VREF
C126 220PF 0603
C140 2200PF 0603
R138 49.9K 0603
2.74K 0603
220PF 0603
C114 2200PF 0603
49.9K 0603
AGND
AGND
R131 5.49K 0603 R123 0603 OUT2LR124 3.32K 0603
C134 100PF 0603 0603 OUT3L-
5.49K 0603 3.32K 0603
100PF 0603
C133 330PF 0603
330PF 0603
DAC2 LEFT
R116 5.49K 0603 OUT2L+ C122 680PF 0603 R117 1.65K 0603
DAC3 LEFT
R136 0603 5.49K 0603 OUT3L+ DAC2_LEFT 680PF 0603 1.65K 0603 AD8606AR SOIC8
AD8606AR SOIC8
0603 CT10 10UF CAP002 DAC3_LEFT
CT14 10UF CAP002
R112 2.74K 0603
C125 220PF 0603
C142 2200PF 0603
R137 49.9K 0603
2.74K 0603
220PF 0603
C102 2200PF 0603
49.9K 0603
AGND
AGND
Populate Manual Jumper Settings
C135 0.22UF
C101 0.22UF
ANALOG DEVICES
Title Size Board
12-1-2004_18:50
Cotton Road Nashua, 03063 1-800-ANALOGD
Blackfin EZ-Extender AUDIO OUT(CH2, CH3) A0193-2004
Sheet
AGND AD8606
AGND AD8606
Date
FER6
10UF CAP002
5.76K 0603
5.76K 0603 ADC2_LEFT 120PF 0603
FER5
10UF CAP002
5.76K 0603
5.76K 0603
ADC1_LEFT
100PF 0603 120PF 0603
100PF 0603
AGND
0603 IN1LAGND
IN2L2
AD8606AR SOIC8 0.001UF 0603 100PF 0603 5.76K 0603 AD8606AR SOIC8 5.76K 0603
5.76K 0603
5.76K 0603
ADC1 LEFT
120PF 0603 750K 0603 IN1L+ AD8606AR SOIC8
120PF 0603 AGND 750K 0603 0603 AD8606AR SOIC8 0.001UF 0603
ADC2 LEFT
IN2L1
AGND AGND
FER7
CT11 10UF CAP002
R122 5.76K 0603
R121 5.76K 0603 ADC2_RIGHT C128 120PF 0603
FER8
CT16 10UF CAP002
R140 5.76K 0603
R134 5.76K 0603
ADC1_RIGHT
C129 100PF 0603
C139 100PF 0603
C141 120PF 0603
AGND
R106 0603 IN1RAGND
IN2R2
AD8606AR SOIC8 C119 0.001UF 0603 C118 100PF 0603 R128 5.76K 0603 AD8606AR SOIC8 R139 5.76K 0603 C143 120PF 0603 R129 750K 0603 IN1R+ AD8606AR SOIC8 AD8606AR SOIC8
R105 5.76K 0603
R120 5.76K 0603
ADC1 RIGHT
ADC2 RIGHT
C127 120PF 0603 AGND R127 750K 0603 R110 0603 C117 0.001UF 0603
IN2R1
AGND AGND
AD1836_VREF
Populate Manual Jumper Settings
0.22UF
C121 0.22UF
C138 0.22UF
0.22UF
ANALOG DEVICES
Title Size Board
10-15-2004_19:35
Cotton Road Nashua, 03063 1-800-ANALOGD
Blackfin EZ-Extender AUDIO IN(CH1, CH2) A0193-2004
Sheet
AGND AD8606
AGND AD8606
AGND AD8606
AGND AD8606
Date
INDEX
AD1836A audio codec, 2-5, 2-10 ADV7183B video decoder, analog audio interface audio interface analog video interface video interface architecture, EZ-Extender, ASDATA1-2 data output pins, 2-13 audio codec, data inputs, interface, jacks, loopback jumpers, 2-14 AV_RESET source jumper, 2-14
block diagram, EZ-Extender,
clock setup jumpers, 2-10 customer support, xiii
data pins PPI0 PPI1 decoder HSync disconnect jumper, output enable jumper, 2-10 VSync connection jumper,
bidirectional buffers, bill materials, encoder HRef connection jumper, 2-10 VSync connection jumper, 2-10
Blackfin EZ-Extender Manual
INDEX
expansion interface connector summary, DR0PRI, DR0SEC, DT0PRI, DT0SEC, FLAG_SCL_DIR_CTRL, FLAG_SDA, MISO, MOSI, PPI0_CLK, PPI0 data pins, PPI0_SYNC1-2, PPI1_CLK, PPI1_D10, PPI1_D2-3, PPI1 data pins, PPI1_FS1-2, RFS0, RSCLK0, SNAPSHOT_FODD_SSEL, TFS0, TSCLK0, expansion interface, EZ-KIT Lite, EZ-Extender interfacing with EZ-KIT Lite, system architecture,
general-purpose flag, 2-10, 2-12, 2-14
HREF, HSYNC,
mode, enable jumper, 2-13 reset, 2-14 interfaces analog audio, analog video, EZ-KIT Lite, flat panel display, Kodak camera modules, Micron camera module, OmniVision camera module,
JP10.1/2, 2-14 JP10.3/4, 2-14 JP1.1/2, JP1.3/4, JP1.5/6, connector, JP3.11/12, JP3.13/14, JP3.15/16, 2-10 JP3.17/18, 2-10 JP3.19/20, 2-10 JP3.21/22, 2-5, 2-10 JP3.3/5/7, 2-4, 2-5, JP3.4/6/8, 2-4, 2-5, JP3.9/10, 2-4, JP4.1/2, 2-4, 2-5, 2-10 JP4.3/4, 2-4, 2-5, 2-10
flag pin, 2-9, 2-14 flat panel displays, FODD (OmniVision camera) signal, 2-10 FPDI signal, interface, signal, frame sync signal, processor, 2-9, 2-10 frame sync signals, 2-2, 2-6, 2-13
Blackfin EZ-Extender Manual
INDEX
JP4.5/6, 2-4, 2-5, 2-10 JP4.7/8, 2-4, 2-5, 2-10 JP5.1/2, 2-11 JP5.3/4, 2-4, 2-5, 2-11 JP5.5/6, 2-4, 2-5, 2-11 JP6.1/3/5, 2-4, 2-12 JP6.2/4/6, 2-4, 2-12 JP7.1/2, 2-13 JP7.3/4, 2-13 JP7.5/6, 2-13 JP8.1/3/5, 2-4, 2-5, 2-13 JP8.2/4/6, 2-4, 2-5, 2-13 JP8.7/8, 2-4, 2-5, 2-13 JP9.1/3/5, 2-14 JP9.2/4/5, JP9.2/4/6, 2-14 jumpers,
PDWN connection jumper, input, PPI0, 2-2, 2-10, 2-13 data bus, 2-4, 2-11, 2-14 data enable jumper, 2-11 data direction setup jumper, 2-14 frame sync signal, PPI0_SYNC1-2 direction setup jumpers, 2-12 PPI1, 2-10, 2-13 PPI_CLK signals, 2-10 product overview,
RFS0 net, RSCLK0 net,
Kodak camera modules, 2-5, KAC-9628,
SNAPSHOT_FODD disconnect jumper, 2-10 source selection jumpers, serial clock, serial input data signal, serial output data signal, SPORT data connection jumpers, 2-13 data input pins, 2-13 Two-Wire Interface (TWI) mode, 2-13 SPORT0, receive clock signal, receive frame sync signal, transmit clock signal, system reset, 2-14
Micron camera modules, MT9V022,
NL6448BC20-08E, flat panel display, notation conventions,
OmniVision camera modules, 2-5, OV6630AA,
wire interface, 2-5,
Blackfin EZ-Extender Manual
INDEX
unidirectional buffers,
video decoder/encoder, interfaces, 2-2, test loopback jumpers,
VID_IN bus, 2-2, 2-4, 2-10 VID_OUT bus, 2-2, 2-4, 2-11 control jumpers, 2-11 sync enable jumper, 2-13 sync source select jumpers, 2-13 voltage selection jumper,
Blackfin EZ-Extender Manual

Revision 1.0, January 2005 Part Number 82-000870-01 Copyright Inf

Top Searches for this datasheet

Other recent searches