T-13/4 Precision Optical Performance AlInGaP Lamps These Precisio
|
|
|
Top Searches for this datasheet
HLMP-ELxx, HLMP-EHxx, HLMP-EJxx, HLMP-EGxx
T-13/4 Precision Optical Performance AlInGaP Lamps
These Precision Optical Performance AlInGaP LEDs provide superior light output excellent readability sunlight extremely reliable. AlInGaP technology provides extremely stable light output over long periods time. Precision Optical Performance lamps utilize aluminum indium gallium phosphide (AlInGaP) technology. These lamps untinted, nondiffused, T-13/4 packages incorporating second generation optics producing well defined spatial radiation patterns specific viewing cone angles. These lamps made with advanced optical grade epoxy, offering superior high temperature high moisture resistance performance outdoor signal sign applications. high maximum junction temperature limit +130°C enables high temperature operation bright sunlight conditions. package epoxy contains both uv-a uv-b inhibitors reduce effects long term exposure direct sunlight. These lamps available package options give designer flexibility with device mounting.
Features
Well defined spatial radiation patterns Viewing angles: 15°, 23°, High luminous output Colors: amber orange reddish-orange High operating temperature: +130°C Superior resistance moisture Package options: With without lead stand-offs
Applications
Traffic management: Traffic signals Pedestrian signals Work zone warning lights Variable message signs Commercial outdoor advertising: Signs Marquees Automotive: Exterior interior lights
Benefits
Viewing angles match traffic management sign requirements Colors meet automotive pedestrian signal specifications Superior performance outdoor environments Suitable autoinsertion onto boards
Device Selection Guide
Typical Viewing Angle (Deg.)[4] Color Dominant Wavelength (nm), Typ.[3] Amber Lamps without Standoffs Leads (Outline Drawing HLMP-EL08-T0000 HLMP-EL08-VY000 HLMP-EL08-VYK00 HLMP-EL08-WZ000 HLMP-EL08-X1K00 HLMP-EL08-X1000 Orange HLMP-EJ08-WZ000 HLMP-EJ08-X1000 HLMP-EJ08-Y2000 Red-Orange HLMP-EH08-UX000 HLMP-EH08-WZ000 HLMP-EH08-X1000 HLMP-EH08-Y2000 HLMP-EG08-T0000 HLMP-EG08-VY000 HLMP-EG08-WZ000 HLMP-EG08-X1000 HLMP-EG08-YZ000 HLMP-EG08-Y2000 HLMP-EG10-Y2000
Notes: luminous intensity measured mechanical axis lamp package. optical axis closely aligned with package mechanical axis. dominant wavelength, derived from Chromaticity Diagram represents color lamp. off-axis angle where luminous intensity half on-axis intensity. Tolerance each intensity limit 15%.
Lamps with Standoffs Leads (Outline Drawing HLMP-EL10-T0000 HLMP-EL10-VY000 HLMP-EL10-WZ000 HLMP-EL10-X1K00 HLMP-EL10-X1000 HLMP-EJ10-X1000 HLMP-EH10-UX000 HLMP-EH10-WZ000 HLMP-EH10-X1000 HLMP-EH10-Y2000 HLMP-EG10-T0000 HLMP-EG10-WZ000 HLMP-EG10-X1000
Luminous Intensity (mcd)[1,2,5] Min. Max. 2500 4200 4200 5500 7200 7200 5500 7200 9300 3200 5500 7200 9300 2500 4200 5500 7200 9300 9300 12000 12000 16000 21000 21000 16000 21000 27000 9300 16000 21000 27000 12000 16000 21000 16000 27000
Device Selection Guide
Typical Viewing Angle (Deg.)[4] Color Dominant Wavelength (nm), Typ.[3] Amber HLMP-EL15-PS000 HLMP-EL15-QSK00 HLMP-EL15-QT000 HLMP-EL15-RU000 HLMP-EL15-TW000 HLMP-EL15-TWK00 HLMP-EL15-UX000 HLMP-EL15-VY000 HLMP-EL15-VYK00 HLMP-EL15-VW000 Orange HLMP-EJ15-PS000 HLMP-EJ15-RU000 HLMP-EJ15-SV000 Red-Orange HLMP-EH15-QT000 HLMP-EH15-RU000 HLMP-EH15-TW000 HLMP-EH15-UX000 HLMP-EG15-N0000 HLMP-EG15-PS000 HLMP-EG15-QT000 HLMP-EG15-RU000 HLMP-EG15-UX000 HLMP-EG15-TW000 HLMP-EG17-QT000 HLMP-EG17-RU000 HLMP-EG17-UX000 HLMP-EG17-TW000 HLMP-EH17-TW000 HLMP-EH17-UX000 HLMP-EG17-N0000 HLMP-EJ17-SV000 HLMP-EJ17-QT000 HLMP-EL17-UX000 HLMP-EL17-VY000 HLMP-EL17-TW000 Lamps without Standoffs Leads (Outline Drawing Lamps with Standoffs Leads (Outline Drawing HLMP-EL17-M0000 Luminous Intensity (mcd)[1,2,5] Min. Max. 1150 1150 1500 2500 2500 3200 4200 4200 4200 1150 1500 1900 1150 1500 2500 3200 1150 1500 3200 2500 2500 2500 3200 4200 7200 7200 9300 12000 12000 7200 3200 2500 4200 5500 3200 4200 7200 9300 2500 3200 4200 9300 7200
Notes: luminous intensity measured mechanical axis lamp package. optical axis closely aligned with package mechanical axis. dominant wavelength, derived from Chromaticity Diagram represents color lamp. off-axis angle where luminous intensity half on-axis intensity. Tolerance each intensity limit 15%.
Device Selection Guide
Typical Viewing Angle (Deg.)[4] Color Dominant Wavelength (nm), Typ.[3] Amber Lamps without Standoffs Leads (Outline Drawing HLMP-EL24-L0000 HLMP-EL24-MQ000 HLMP-EL24-NR000 HLMP-EL24-PS000 HLMP-EL24-QR000 HLMP-EL24-QRK00 HLMP-EL24-QS400 HLMP-EL24-QT000 HLMP-EL24-RU000 HLMP-EL24-RUK00 HLMP-EL24-SV000 HLMP-EL24-SUK00 HLMP-EL24-SU400 HLMP-EL24-SVK00 HLMP-EL24-TW000 HLMP-EL24-TWK00 Orange Red-Orange HLMP-EJ24-QT000 HLMP-EH24-PS000 HLMP-EH24-QT000 HLMP-EH24-RU000 HLMP-EH24-SV000 HLMP-EG24-M0000 HLMP-EG24-PS000 HLMP-EG24-QT000 HLMP-EG24-RU000 HLMP-EG26-RU000
Notes: luminous intensity measured mechanical axis lamp package. optical axis closely aligned with package mechanical axis. dominant wavelength, derived from Chromaticity Diagram represents color lamp. off-axis angle where luminous intensity half on-axis intensity. Tolerance each intensity limit 15%.
Lamps with Standoffs Leads (Outline Drawing HLMP-EL26-L0000
Luminous Intensity (mcd)[1,2,5] Min. Max. 1500 1900 2500 1900 1900 2500 3200 4200 4200 5500 4200 4200 5500 7200 7200 3200 2500 3200 4200 5500 2500 4200 4200
HLMP-EL26-PS000
1150 1150 1150
HLMP-EL26-QT000 HLMP-EL26-RU000 HLMP-EL26-SV000
1150 1150 1150 1900 1900 1900 1900
HLMP-EL26-TW000
2500 2500 1150
HLMP-EH26-PS000
1150 1500
HLMP-EH26-SV000 HLMP-EG26-M0000 HLMP-EG26-PS000
1900 1150 1500
Device Selection Guide
Typical Viewing Angle (Deg.)[4] Color Dominant Wavelength (nm), Typ.[3] Amber Lamps without Standoffs Leads (Outline Drawing HLMP-EL30-K0000 HLMP-EL30-MQ000 HLMP-EL32-NR000 HLMP-EL30-PQ000 HLMP-EL30-PR400 HLMP-EL30-PS000 HLMP-EL30-PSK00 HLMP-EL30-QT000 HLMP-EL30-QTK00 HLMP-EL30-ST000 HLMP-EL30-SU400 HLMP-EL30-SUK00 HLMP-EL30-STK00 HLMP-EL30-SV000 HLMP-EL30-SVK00 Orange Red-Orange HLMP-EJ30-NR000 HLMP-EJ30-PS000 HLMP-EH30-MQ000 HLMP-EH30-NR000 HLMP-EH30-PS000 HLMP-EH30-QT000 HLMP-EH30-RU000 HLMP-EG30-K0000 HLMP-EG30-KN000 HLMP-EG30-MQ000 HLMP-EG30-NQ000 HLMP-EG30-NR000 HLMP-EG30-PQ000 HLMP-EG30-PR000 HLMP-EG30-PS000 HLMP-EG30-QT000 HLMP-EG32-QT000
Notes: luminous intensity measured mechanical axis lamp package. optical axis closely aligned with package mechanical axis. dominant wavelength, derived from Chromaticity Diagram represents color lamp. off-axis angle where luminous intensity half on-axis intensity. Tolerance each intensity limit 15%.
Lamps with Standoffs Leads (Outline Drawing HLMP-EL32-K0000
Luminous Intensity (mcd)[1,2,5] Min. Max. 1500 1900 1500 1900 2500 2500 3200 3200 3200 4200 4200 3200 5500 5500 1900 2500 1500 1900 2500 4200 4200 1500 1500 1900 1500 1900 2500 3200
HLMP-EL32-PS000 HLMP-EL32-QT000
1150 1150 1900 1900 1900 1900
HLMP-EL32-SV000
1900 1900
HLMP-EJ32-PS000 HLMP-EH32-MQ000 HLMP-EH32-NR000 HLMP-EH32-PS000 HLMP-EH32-QT000 HLMP-EH32-RU000 HLMP-EG32-K0000 HLMP-EG32-MQ000 HLMP-EG32-NR000
1150 1500 1150
Part Numbering System
HLMP
Mechanical Options Bulk Packaging Ammo Pack Flexi-Bin; Bulk Packaging Flexi-Bin; Ammo Pack Color Selections color limitation Amber color only Amber color bins only Maximum Intensity limitation Minimum Intensity Viewing Angle Lead Stand Offs without lead stand offs with lead stand offs without lead stand offs with lead stand offs without lead stand offs with lead stand offs without lead stand offs with lead stand offs Color Red-Orange Orange Amber Package Round
Note: Please refer 5337 complete information part numbering system.
Package Dimensions
5.00 0.20 (0.197 0.008) 1.14 0.20 (0.045 0.008)
5.00 0.20 (0.197 0.008)
8.71 0.20 (0.343 0.008)
8.71 0.20 (0.343 0.008)
2.35 (0.093) MAX. 0.70 (0.028) MAX. 31.60 MIN. (1.244)
1.14 0.20 (0.045 0.008)
31.60 MIN. (1.244)
1.50 0.15 (0.059 0.006) 0.70 (0.028) MAX. CATHODE LEAD
CATHODE LEAD
1.00 MIN. (0.039)
0.50 0.10 TYP. (0.020 0.004)
1.00 MIN. (0.039)
0.50 0.10 TYP. (0.020 0.004)
CATHODE FLAT
5.80 0.20 (0.228 0.008)
2.54 0.38 (0.100 0.015) NOTES: DIMENSIONS MILLIMETERS (INCHES). LEADS MILD STEEL, SOLDER DIPPED. TAPERS SHOWN LEADS (BOTTOM LAMP PACKAGE) INDICATE EPOXY MENISCUS THAT EXTEND ABOUT (0.040 in.) DOWN LEADS. NOTES: DOME HEIGHTS ABOVE LEAD STAND-OFF SEATING PLANE, LAMP PACKAGE TABLE.
CATHODE FLAT
5.80 0.20 (0.228 0.008)
2.54 0.38 (0.100 0.015)
DIMENSIONS MILLIMETERS (INCHES). TAPERS SHOWN LEADS (BOTTOM LAMP PACKAGE) INDICATE EPOXY MENISCUS THAT EXTEND ABOUT (0.040 in.) DOWN LEADS. DOME HEIGHTS ABOVE LEAD STAND-OFF SEATING PLANE, LAMP PACKAGE TABLE.
PART HLMP-XX10 HLMP-XX17 HLMP-XX26 HLMP-XX32
12.37 0.25 (0.487 0.010) 12.42 0.25 (0.489 0.010) 12.52 0.25 (0.493 0.010) 11.96 0.25 (0.471 0.010)
Absolute Maximum Ratings 25°C
Forward Current[1,2,3] Peak Pulsed Forward Current[2,3] .100 Average Forward Current[3] Reverse Voltage Junction Temperature. 130°C Operating Temperature .-40°C +100°C Storage Temperature .-40°C +100°C
Notes: Derate linearly shown Figure long term performance with minimal light output degradation, drive currents between recommended. more information recommended drive conditions, please refer Application Brief I-024. Operating currents below recommended. Please contact your local representative further information.
Electrical/Optical Characteristics 25°C
Parameter
Forward Voltage Amber Orange Red-Orange Reverse Voltage Peak Wavelength: Amber Orange Red-Orange Spectral Halfwidth
Symbol
PEAK
Min.
Typ.
2.02 1.98 1.94 1.90
Max.
Units
Test Conditions
Peak Wavelength Spectral Distribution Wavelength Width Spectral Distribution Power Point Exponential Time Constant, e-t/ts Junction-to-Cathode Lead Emitted Luminous Power/Emitted Radiant Power
Speed Response Capacitance Thermal Resistance Luminous Efficacy[1] Amber Orange Red-Orange Luminous Flux Luminous Efficiency Amber Orange Red-Orange Note:
RJ-PIN
°C/W
lm/W
lm/W
Emitted Luminous Flux/Electrical Power
radiant intensity, watts steradian, found from equation Iv/hv, where luminous intensity candelas luminous efficacy lumens/watt. where emitted luminous flux, electrical forward current forward voltage.
AMBER ORANGE RELATIVE INTENSITY RED-ORANGE CURRENT
AMBER
WAVELENGTH
FORWARD VOLTAGE
Figure Relative intensity peak wavelength
Figure Forward current forward voltage
RELATIVE LUMINOUS INTENSITY (NORMALIZED
FORWARD CURRENT
AMBIENT TEMPERATURE
FORWARD CURRENT
Figure Relative luminous intensity forward current
Figure Maximum forward current ambient temperature
NORMALIZED INTENSITY
ANGULAR DISPLACEMENT DEGREES
Figure Representative spatial radiation pattern viewing angle lamps
NORMALIZED INTENSITY
ANGULAR DISPLACEMENT DEGREES
Figure Representative spatial radiation pattern viewing angle lamps
NORMALIZED INTENSITY
-100 ANGULAR DISPLACEMENT DEGREES
Figure Representative spatial radiation pattern viewing angle lamps
NORMALIZED INTENSITY
ANGULAR DISPLACEMENT DEGREES
Figure Representative spatial radiation pattern viewing angle lamps
ORANGE RED-ORANGE AMBER
Intensity Limits
(mcd Name
RELATIVE (NORMALIZED 25°C)
Min.
1150 1500 1900 2500 3200 4200 5500 7200 9300 12000 16000 21000
Max.
1150 1500 1900 2500 3200 4200 5500 7200 9300 12000 16000 21000 27000
JUNCTION TEMPERATURE
Figure Relative light output junction temperature
Tolerance each limit 15%.
Amber Color Limits
Name
Min.
584.5 587.0 589.5 592.0
Max.
587.0 589.5 592.0 594.5
Tolerance each limit
Note: categories established classification products. Products available categories.
Precautions:
Lead Forming:
leads lamp preformed length prior insertion soldering board. better control, recommended proper tool precisely form leads applicable length rather than doing manually. manual lead cutting necessary, leads after soldering process. solder connection forms mechanical ground which prevents mechanical stress lead cutting from traveling into package. This highly recommended hand solder operation, excess lead length also acts small heat sink.
Note: with different size design (component density) will have different heat mass (heat capacity). This might cause change temperature experienced board same wave soldering setting used. recommended re-calibrate soldering profile again before loading type PCB. Avago Technologies' high brightness using high efficiency with single wire bond shown below. Customer advised take extra precaution during wave soldering ensure that maximum wave temperature does exceed 250°C solder contact time does exceeding 3sec. Over-stressing during soldering process might cause premature failure delamination.
Avago Technologies configuration
Soldering Handling:
Care must taken during assembly soldering process prevent damage component. component effectively hand soldered PCB. However, only recommended under unavoidable circumstances such rework. closest manual soldering distance soldering heat source (soldering iron's tip) body 1.59mm. Soldering using soldering iron closer than 1.59mm might damage LED.
1.59mm
CATHODE
Note: Electrical connection between bottom surface AllnGaP Device lead frame achieved through conductive paste.
alignment fixture that being applied during wave soldering should loosely fitted should apply weight force LED. metal material recommended will absorb less heat during wave soldering process. elevated temperature, more susceptible mechanical stress. Therefore, must allowed cool down room temperature prior handling, which includes removal alignment fixture pallet. board contains both through hole (TH) other surface mount components, recommended that surface mount components soldered side PCB. surface mount need bottom side, these components should soldered using reflow soldering prior insertion LED. Recommended board plated through holes (PTH) size component leads.
component lead size Diagonal Plated through hole diameter 0.98 1.08 (0.039 0.043 inch) 1.05 1.15 (0.041 0.045 inch)
precaution must properly applied soldering station personnel prevent damage component that sensitive. refer Avago application note 1142 details. soldering iron used should have grounded ensure electrostatic charge properly grounded. Recommended soldering condition:
Wave Soldering Pre-heat temperature Preheat time Peak temperature Dwell time Max. Max. Max. Manual Solder Dipping Max.
Note: Above conditions refers measurement with thermocouple mounted bottom PCB. recommended only bottom preheaters order reduce thermal stress experienced LED.
0.45 0.45 0.636 (0.018x 0.018 inch) (0.025 inch) 0.50 0.50 0.707 (0.020x 0.020 inch) (0.028 inch)
Wave soldering parameters must maintained according recommended temperature dwell time. Customer advised perform daily check soldering profile ensure that always conforming recommended soldering conditions.
Over-sizing lead twisted after clinching. other hand under sizing cause difficulty inserting LED.
Refer application note AN5334 more information about soldering handling high brightness lamps.
Example Wave Soldering Temperature Profile
TURBULENT WAVE LAMINAR WAVE KNIFE
Recommended solder: Sn63 (Leaded solder alloy) SAC305 (Lead free solder alloy) Flux: Rosin flux
Solder bath temperature: 245°C± (maximum peak temperature 250°C) Dwell time: (maximum 3sec) Note: Allow board sufficiently cooled room temperature before exerting mechanical force.
PREHEAT
TIME (MINUTES)
Figure Recommended wave soldering profile
Ammo Pack Drawing
6.35 1.30 (0.25 0.0512) 12.70 1.00 (0.50 0.0394)
CATHODE
20.50 1.00 (0.807 0.039) 9.125 0.625 (0.3593 0.0246) 18.00 0.50 (0.7087 0.0197)
12.70 0.30 (0.50 0.0118) 0.70 0.20 (0.0276 0.0079) DIMENSIONS MILLIMETERS (INCHES).
VIEW
4.00 0.20 TYP. (0.1575 0.008)
NOTE: AMMO-PACKS DRAWING APPLICABLE PACKAGING OPTION REGARDLESS STANDOFF NON-STANDOFF.
Packaging Ammo Packs
LABEL THIS SIDE BOX. FROM LEFT SIDE BOX, ADHESIVE TAPE MUST FACING UPWARD.
ANODE LEAD LEAVES FIRST.
LOGI
NOTE: DIMENSION AMMO PACK APPLICABLE DEVICE WITH STANDOFF WITHOUT STANDOFF.
Packaging Label:
Avago Mother Label: (Available packaging ammo pack shipping box)
(1P) Item: Part Number (1T) Lot: Number LPN: (9D)MFG Date: Manufacturing Date Customer Item: Vendor DeptID:
STANDARD LABEL LS0002 RoHS Compliant temp 250C
QTY: Quantity CAT: Intensity BIN: Refer below information
(9D) Date Code: Date Code Made Country Origin
Lamps Baby Label (1P) PART Part Number
RoHS Compliant temp 250C
DeptID:
Made Country Origin
(ii) Avago Baby Label (Only available bulk packaging)
Lamps Baby Label (1P) PART Part Number (1T) Number (9D)MFG DATE: Manufacturing Date C/O: Country Origin Customer P/N: Supplier Code:
RoHS Compliant temp 250C
QUANTITY: Packing Quantity
CAT: Intensity BIN: Refer below information DATECODE: Date Code
Acronyms Definition:
BIN: Color only only (Applicable part number with color bins without part number with bins color bin) (ii) Color incorporated with (Applicable part number that have both color bin) Example: Color only only BIN: (represent color only) BIN: (represent "VB" only) (ii) Color incorporate with BIN: "VB" Color only
DISCLAIMER: AVAGO'S PRODUCTS SOFTWARE SPECIFICALLY DESIGNED, MANUFACTURED AUTHORIZED SALE PARTS, COMPONENTS ASSEMBLIES PLANNING, CONSTRUCTION, MAINTENANCE DIRECT OPERATION NUCLEAR FACILITY MEDICAL DEVICES APPLICATIONS. CUSTOMER SOLELY RESPONSIBLE, WAIVES RIGHTS MAKE CLAIMS AGAINST AVAGO SUPPLIERS, LOSS, DAMAGE, EXPENSE LIABILITY CONNECTION WITH SUCH USE.
product information complete list distributors, please website:
www.avagotech.com
Avago, Avago Technologies, logo trademarks Avago Technologies United States other countries. Data subject change. Copyright 2005-2008 Avago Technologies. rights reserved. Obsoletes 5989-4368EN AV02-0373EN September 2008
Other recent searches
XZBBA55W-A2 - XZBBA55W-A2 XZBBA55W-A2 Datasheet
SPB08P06P - SPB08P06P SPB08P06P Datasheet
PI74LCX241 - PI74LCX241 PI74LCX241 Datasheet
MB86C30A - MB86C30A MB86C30A Datasheet
LT1D73-AN - LT1D73-AN LT1D73-AN Datasheet
HT95L100 - HT95L100 HT95L100 Datasheet
EUP8010X - EUP8010X EUP8010X Datasheet
DIP20H - DIP20H DIP20H Datasheet
Privacy Policy | Disclaimer
© 2012 Datasheet Archive
