FlexiPanel Evaluation board Toothpick, LinkMatik, Bluematik Tooth

The Datasheet Archive - 100 Million Datasheets from 7500 Manufacturers.

FlexiPanel Evaluation board Toothpick, LinkMatik, Bluematik Tooth

Datasheet Thumbnail

Top Searches for this datasheet

Bluetooth Evaluation Board
FlexiPanel
Evaluation board Toothpick, LinkMatik, Bluematik Toothpick Stamp Edition
Summary
Bluetooth Evaluation Board designed evaluate FlexiPanel Ltd's Bluetooth products: Toothpick LinkMatik BlueMatik Toothpick Stamp Edition
Features
Sockets modules Power regulator, switch LED, powered from 5-12V Jumper switches board configuration RS232 serial port RS232 converter Toothpick ICD2 programming socket 24C256 memory chip pushbuttons, LEDs, presets switches tutorials products data sheets.
These supplied with evaluation board must bought separately.
Ordering Information
Part BTEVAL Description Bluetooth Evaluation Board
Manufactured ISO9001:2000
Page 30-Mar-06
Bluetooth Evaluation Board DS378-2
FlexiPanel
Patents apply and/or pending
www.FlexiPanel.com
Evaluation Board Overview
Intended uses
primary Bluetooth Evaluation Board allow evaluation FlexiPanel Ltd's Bluetooth products easily possible. designed allow developer follow tutorials examples product data sheets. Additionally, evaluation board used during development reliable, tested environment while troubleshooting.
memory
24C256 serial memory conditionally connected, according configuration pins, pins Toothpick. Pull-up resistors included. address pins held low, Toothpick mStr value access memory 0x10.
ICD2 programming connector
RJ11 programming connector allows program ToothPIC directly using Microchip MPLAB ICD2. Since NMCLR, INT0 INT1 lines must isolated, BASIC Stamp should installed same time IDC2 connected.
Power Supply
evaluation board powered reasonable smooth unregulated power source 2.5mm center-positive connector. heat sink provided voltage regulator, expect quite warm.
Jumper connections
Jumper connections allow evaluation board dynamically reconfigured detailed General Setup sections. printed next each jumper connection strip. columns denoted letters, rows numbers. Note that links might need inserted either horizontal vertical positions.
Switches, LEDs Presets
following peripheral permanently connected: components
LEDs Toothpick pins AN9, AN10, AN11, CCP1 SDO. Presets that vary voltage Toothpick pins AN0, AN1, smoothly between Pushbuttons control voltages Toothpick pins AN4, AN5, AN7. when pressed otherwise. binary encoding rotary switch CCP5. binary encoding rotary switch unconnected. Power LED. connected Status LinkMatik BlueMatik. following peripheral components conditionally connected according configuration pins detailed General Setup sections: LEDs Toothpick pins CCP2, CCP3, SDA, SCL, binary encoding rotary switch CCP4. binary encoding rotary switch RxD.
Page 30-Mar-06 Bluetooth Evaluation Board DS378-2
Switches
switches LinkMatik Connect Sleep between Sleep state state. used switch LinkMatik Master Slave Mode between Master Slave modes, switch BlueMatik between Command Data modes. Note that whether this switch effect depends jumper settings, since these modes alternately driven state RS232 line.
RS232 driver Serial Port
serial port used Toothpick, LinkMatik, BlueMatik BASIC Stamp according configuration.
Module Sockets
Only insert BlueMatik, LinkMatik Toothpick time. Only insert BASIC Stamp when used with Toothpick Stamp Edition.
Patents apply and/or pending www.FlexiPanel.com
FlexiPanel
Toothpick
General Setup
Insert Toothpick evaluation board that antenna overhangs edge board. There should nothing inserted LinkMatik, Stamp BlueMatik sockets. Remove existing links then insert links over following configuration pins: C10- (CCP4 rotary switch)* (CCP3 LED) (CCP2 LED) (TxD LED)
Toothpick Slave Tutorial
follow Toothpick Slave tutorial provided Toothpick data sheet, remove existing links then connect links RS232 flow control) follows: C10- (RS232 pin) (RS232 pin) (SDA memory) (RS232 pin) (CCP4 rotary switch) (CCP3 LED) (CCP2 LED) (SCL memory) (TxD LED)
*Note: version board (TPDr5), incorrectly labeled rear RS232 port used (e.g. DARC-I tutorial) insert links over following configuration pins: (RS232 pin) (RS232 pin) (RS232 pin)
Step tutorial, adding RS232 level shifting circuit, complete simply connect your serial port socket evaluation board. will glow more less continually during tutorial because usually high state. follow tutorial exactly data sheet. When have completed tutorial might like experiment with memory follows: Type command: 04010C01 activate memory. This command nonvolatile setting which only takes effect after device reset, type command 0200 reset Toothpick wait greeting message. store values 0x05, 0x06, 0x07, 0x08 location 0x0100, type command 090F10000105060708 retrieve those same values, type command 060E10000104 retrieved values will last characters response.
addition, flow control used (e.g. DARC-I tutorial) insert links over following configuration pins. ICD2 programming socket cannot used with these pins place: A10- (RS232 INT0 pin) (RS232 INT0 pin) (RS232 INT1 pin) (RS232 INT1 pin)
RS232 port used (e.g. DARC-II tutorial) insert link over following configuration pin: (RxD rotary switch)
memory used insert links over following configuration pins: (SDA memory) (SCL memory)
memory used insert links over following configuration pins:
Page 30-Mar-06
(SCL LED) (SDA LED)
Bluetooth Evaluation Board DS378-2
FlexiPanel
Patents apply and/or pending
www.FlexiPanel.com
DARC-I Tutorial
follow DARC-I tutorial provided DARC-I data sheet, remove existing links then connect links RS232 follows: C10- (SCL LED) (SDA LED) (CCP4 rotary switch) (CCP3 LED) (CCP2 LED) (RxD rotary switch) (TxD LED)
DARC-II Tutorial
follow DARC-II tutorial provided DARC-II data sheet, remove existing links then connect links RS232 follows: C10- (SCL LED) (SDA LED) (CCP4 rotary switch) (CCP3 LED) (CCP2 LED) (RxD rotary switch) (TxD LED)
follow tutorial exactly data sheet. Remember that presets connected AN1, allowing voltages these pins easily.
follow tutorial exactly data sheet. Remember that presets connected AN2, allowing voltages these pins easily. parallel input comprised CCP5/CCP4/RxD connected rotary switch.
Page 30-Mar-06
Bluetooth Evaluation Board DS378-2
FlexiPanel
Patents apply and/or pending
www.FlexiPanel.com
LinkMatik
General Setup
Insert LinkMatik evaluation board that antenna overhangs edge board. There should nothing inserted Toothpick, Stamp BlueMatik sockets. Remove existing links then insert links over following configuration pins: A10- (RS232 pin) (RS232 pin)* (RS232 pin)* (RS232 pin) (RS232 pin) (RS232 pin)
Slave Mode
evaluate LinkMatik slave mode, switch Sleep position, remove existing links then connect links follows: A10- (RS232 pin) (RS232 pin) (RS232 pin) (RS232 pin) (RS232 pin) (RS232 pin) (SW6 input) (RS232 pin) (RS232 pin)
*Note: version board (TPDr5 omitted rearside labels. decide whether input controlled switch line RS232 port. control from switch SW6, insert link over following configuration pin: (SW6 input)
LinkMatik configured that input controlled Connect Sleep line controlled SW7. Apply power into position. Then into position. Status should flash indicate that entered Slave mode waiting device connect LinkMatik working, HyperTerminal sessions much started will connected RS232 port, other Bluetooth. What type into console will appear other. First connect socket your PC's serial port. Start HyperTerminal session 9600 baud, hardware flow control, bits parity, stop bit. Second, Bluetooth Manager your discover LinkMatik. will need pair with since security enabled. code four zeroes `0000'. Connect LinkMatik observe that Status glows steadily connection complete. Start another HyperTerminal session, using port number assigned Bluetooth Manager when made connection. baud settings ignored, enter anything like them. should find that anything type HyperTerminal window appears other HyperTerminal window.
control input from line, insert links over following configuration pins: (DTR input) (DTR input)
operate normal transceiver mode, insert links over following configuration pins: (RS232 pin) (RS232 pin)
operate configuration mode, insert links over following configuration pins: (4k7 pull-down pin) (4k7 pull-down pin)
Page 30-Mar-06
Bluetooth Evaluation Board DS378-2
FlexiPanel
Patents apply and/or pending
www.FlexiPanel.com
Configuration Mode
Important: have previously Slave Mode evaluation, sure close HyperTerminal windows they will otherwise `hog' ports prevent correct Bluetooth communication. evaluate LinkMatik configuration mode, switch Sleep position, remove existing links then connect links follows: A10- (RS232 pin) (RS232 pin) (RS232 pin) (RS232 pin) (RS232 pin) (RS232 pin) (SW6 input) (4k7 pull-down pin) (4k7 pull-down pin)
Master Mode
evaluate LinkMatik master mode, first complete configuration mode evaluation since this configure LinkMatik connect your with switch Sleep position, remove existing links then connect links slave mode evaluation: A10- (RS232 pin) (RS232 pin) (RS232 pin) (RS232 pin) (RS232 pin) (RS232 pin) (SW6 input) (RS232 pin) (RS232 pin)
LinkMatik configured that input controlled Connect Sleep line controlled SW7. Apply power into Mstr position. Then into position. Status should flash indicate that entered Master mode looking connect your After seconds should discover your will automatically connect Depending whether previous pairings have been remembered not, necessary enter code 0000 again. wish verify that connection working, start HyperTerminal sessions Slave Mode evaluation. What type into console will appear other.
Apply power into position. Status should flash rapidly, indicating that configuration mode. Bluetooth Manager your discover LinkMatik connect your computer requires code four zeroes 0000. Also Bluetooth Manager, make note your PC's Bluetooth device name. Start LinkMatik configuration tool enter first characters PC's Bluetooth device name Pair Match Prefix. example, used write this documentation name FlexiPanel Vaio Laptop, FlexiPanel entered Pair Match Prefix. This being done that next section, where master mode evaluated, LinkMatik will search connect Press Program LinkMatik button write settings LinkMatik. will extinguish second then glow steadily indicating configuration complete. first time power after programming,
Page 30-Mar-06
Bluetooth Evaluation Board DS378-2
FlexiPanel
Patents apply and/or pending
www.FlexiPanel.com
BlueMatik
General Setup
Insert BlueMatik evaluation board that antenna overhangs edge board. There should nothing inserted Toothpick, Stamp LinkMatik sockets. Remove existing links then insert links over following configuration pins: A10- (RS232 pin) (RS232 pin) (RS232 pin) (RS232 pin) (RS232 pin) (RS232 pin) (RS232 pin) (TxD LED) (RS232 pin)
Example commands
following examples exhaustive. Refer product documentation full list commands. Apply power following greetings message similar following will appear: +BINF:830,2,C7,1D4140,Anonymous READY wait seconds before typing anything, following message will also appear: +BURT:1D8,0,0 This simply indicates that baud rate reverted 115200 baud (which anyway), since input been received first seconds. Note extinguishes while response being send. This differentiate between response from BlueMatik data from Bluetooth connection. discover Bluetooth devices range, type following command: +BURT:1D8,0,0 This starts second scan devices. Each device found will result message similar following: following message indicates that scan complete: +BINC:1 BlueMatik into encrypted slave mode that other devices connect securely, type following commands: AT+BRSR=1,0 AT+BWLP=7 AT+BSEC=2 AT+BSLV
FlexiPanel Patents apply and/or pending
decide whether input controlled switch line RS232 port. control from switch SW6, insert link over following configuration pin: (SW6 input)
control input from line, insert links over following configuration pins: (DTR input) (DTR input)
Evaluation Setup
LinkMatik should configured that input controlled output lights Status LED. Ensure position. First connect socket your PC's serial port. Start HyperTerminal session 115200 baud, hardware flow control, bits parity, stop bit. File Properties Settings ASCII Setup, ensure following checked: Echo characters typed locally Append line feeds incoming line ends Also ensure following checked Send line ends with line feeds
(replies then +BRSR) (replies (replies (replies
www.FlexiPanel.com
Page 30-Mar-06
Bluetooth Evaluation Board DS378-2
Then Bluetooth Manager your discover BlueMatik. When have discovered select Bluetooth Manager pair with using code 0000 (four zeroes). message similar following will appear: +BLNK:800,46,B939B0 indicate that have link yet, should respond typing: AT+BLNK= will then receive message: +BPIN:800,46,B939B0 then pair with code typing: AT+BPIN=0000 When pairing complete, will receive message similar following: +BPRC:800,46,B939B0,9538CD9793. final 32-digit number link key, which could future connect securely without specifying code. that devices paired, Bluetooth Manager your connect BlueMatik. following message will appear: +BMSC:B,0 +BRFC:800,46,B939B0,0,0,0 +BMSC:3,3B These indicate that device connected. Start another HyperTerminal session, using port number assigned Bluetooth Manager when made connection. baud settings ignored, enter anything like them. send data first HyperTerminal, type into second console (the just created) observe that text appears first console also. light does extinguish, indicating that text data rather than command response from BlueMatik. send data from first HyperTerminal, switch Data position that BlueMatik knows
Page 30-Mar-06 Bluetooth Evaluation Board DS378-2
that wish send data. Then type into first console observe that text appears first console also. disconnect connection, switch back position type following command: AT+BDIS BlueMatik will respond with +BRFC=0,0,0,. This indicates that connection ended.
FlexiPanel
Patents apply and/or pending
www.FlexiPanel.com
Toothpick Stamp Edition
General Setup
Insert Toothpick Stamp Edition evaluation board that antenna overhangs edge board. Insert BASIC Stamp evaluation board. There should nothing inserted LinkMatik BlueMatik sockets. Remove existing links then insert links over following configuration pins: (4k7 pull-up Data pin) (TxD LED)
follow tutorial exactly detailed ToothPIC Stamp Edition data sheet. Note that will light more less continuously because Toothpick usually high state.
(IV) Controlling Toothpick
perform tutorial Controlling Toothpick I/O, keep links from previous section. this tutorial, there need connect CCP1 since evaluation board does this you. However, would better monitor voltage rather than AN11 pin, since this variable resistor connected this, open program IOComms.bsp locate following line:
SEROUT TxPinNo, Baud, $02, $04,
program Stamp from Toothpick pins CCP2, CCP3 CCP4, insert links over following configuration pins: (CCP4 ATN) (CCP2 Sin) (CCP3 Sout)
program Stamp from serial port, insert links over following configuration pins: C10- (DSR RS232) (RS232 Sin) (RS232 Sout) (RS232 ATN) (CCP4 rotary switch) (CCP3 LED) (CCP2 LED)
tutorial tells change $03. addition, change $10, will measure value rather than AN11. control voltage this using variable resistor marked AN0, closest Stamp.
Managing Bluetooth Comms
perform tutorial Managing Bluetooth Communications, keep links from previous section. would better monitor voltage rather than AN11 pin, since this variable resistor connected this, open program BTComms.bsp locate following line:
SEROUT TxPinNo, Baud, $02, $04,
(II) Programming Stamp
perform tutorial Programming Stamp from Toothpick Stamp Edition, remove existing links then connect links follows: (4k7 pull-up Data pin) (TxD LED) (CCP4 ATN) (CCP2 Sin) (CCP3 Sout)
Change measure value rather than AN11. control voltage this using variable resistor marked AN0, closest Stamp.
(VI) Creating User Interfaces
follow tutorial exactly detailed ToothPIC Stamp Edition data sheet.
then follow tutorial exactly detailed ToothPIC Stamp Edition data sheet.
(III) Sending Commands
perform tutorial Sending Commands Toothpick Stamp Edition, keep links from previous section.
(VII) Interacting with User Interface
perform tutorial Interacting with User Interface, will need program Stamp using programming cable. There reasons this. first that will wish
Patents apply and/or pending www.FlexiPanel.com
Page 30-Mar-06
Bluetooth Evaluation Board DS378-2
FlexiPanel
Bluetooth radio creating user interface connect debug terminal same time. second that will want CCP3 output rather than programming Stamp. Remove existing links then connect links follows: C10- (TxD LED) (4k7 pull-up Data pin) (DSR RS232) (RS232 Sin) (RS232 Sout) (RS232 ATN) (CCP4 rotary switch) (CCP3 LED) (CCP2 LED)
follow tutorial exactly detailed ToothPIC Stamp Edition data sheet.
Page 30-Mar-06
Bluetooth Evaluation Board DS378-2
FlexiPanel
Patents apply and/or pending
www.FlexiPanel.com
Contact Details
Sales
ToothPIC Stamp Edition distributed supported Parallax Menlo Suite Rocklin 95765, sales: 1024 tel: 8333 tech support email: support@parallax.com http://www.parallax.com Other FlexiPanel Bluetooth products distributed Solutions Unit Cliffe Industrial Estate, Lewes, Sussex 6JL, United Kingdom email sales@rfsolutions.co.uk http://www.rfsolutions.co.uk Tel: (0)1273 Fax: (0)1273
Technical Information Customization Contact Details
ToothPIC owned designed FlexiPanel Ltd. technical support, contact FlexiPanel Ltd: FlexiPanel Suite 120, Westbourne Studios Acklam Road London 5JJ, United Kingdom www.flexipanel.com 7524 7774 email: support@flexipanel.com
FlexiPanel
Page 30-Mar-06
Bluetooth Evaluation Board DS378-2
FlexiPanel
Patents apply and/or pending
www.FlexiPanel.com

FlexiPanel Evaluation board Toothpick, LinkMatik, Bluematik Tooth

Top Searches for this datasheet

Other recent searches