MB86296-EB01 Rev. 1.01 CORAL Evaluation Board 2007 1.01
|
|
|
Top Searches for this datasheet
CORAL
MB86296-EB01 Rev. 1.01
CORAL Evaluation Board
2007
1.01
Revision 1.01 2007 Fujitsu Microelectronics Europe
Page
MB86296-EB01 Evaluation Board Manual
Revision Control
Revision Number Date Description changes 1.00 15/07/2004 First official release 1.01 19/02/2007 Replaced Coral with Coral
Page
Revision 1.01 2007 Fujitsu Microelectronics Europe
MB86296-EB01 Evaluation Board Manual
CONTENTS
Overview.4 Hardware Installation System Components External Appearance Jumper Settings LEDs Expansion Connectors.10 Multiplexed Pins Coral Memory Worldwide Headquarters Disclaimer.14
Revision 1.01 2007 Fujitsu Microelectronics Europe
Page
MB86296-EB01 Evaluation Board Manual
Overview
This evaluation board designed evaluate test functions Fujitsu MB86296 "Coral graphic controller. evaluation board used 3.3V system (PCI compliant V2.1) frequency. Example software drivers included this system developed Windows 2000 Windows
Hardware Installation
order install MB86295S-EB01 evaluation board your system, follow these instructions: Make sure jumpers their default position (refer "Jumper Settings"). Power down your target system other environment) insert card. Note that either 3.3V systems used. Voltage level converters allow operation evaluation board environment Coral graphic controller 3.3V interface only. Restart your target system Install software driver example software (refer software installation instructions ROM) Connect monitor RGB-output connector J350 examples provided
Page
Revision 1.01 2007 Fujitsu Microelectronics Europe
MB86296-EB01 Evaluation Board Manual
System Components
Triple Video ADV7120
Coral-PA Evaluation Card block diagram
main components MB86296-EB01 evaluation board are: "Coral Graphic Controller (MB86296) 64Mbyte SDRAM 256Mbit, bit, (K4S561632C) Video Input Processor (SAA7113) Analog Input (AD9883) Analog Output (ADV7125) Switching Logic multiplexed Inputs/Outputs Output connector Input connector Composite Video input connector Expansion Connector 40pin dual connector Test LEDs Configuration Jumpers
COMP
NTSC
ANALOG SIGNAL SWITCHING
RGB[0:7]
Clocks PLLs
Power Filtering
TRIPLE SYNC ICS1531
RGB666
Video Input Processor SAA7113
Coral MB86296
MD[16:31]
SDRAM SDRAM
MA[0:14]
MD[0:15]
Revision 1.01 2007 Fujitsu Microelectronics Europe
Page
MB86296-EB01 Evaluation Board Manual
External Appearance
Reset Switch
output J250, JP250JP254
Expansion connector J200
Jumpers J300 J301 JP300
Expansion connector J207
Position main external components jumpers
Page
Output
Testpins
LEDs enable J201-J206 1.8V supply level J153
J500
1.8V
Input
Comp Video Input
SDRAM
MB86296S "Coral
Interrupt, Power, Reset, enable, reset Coral: J151, J100, JP550, J104
Buffer Control JP1-JP4 3.3V power supply JP150
3.3V
settings J101-J103, J152
SDRAM
Revision 1.01 2007 Fujitsu Microelectronics Europe
MB86296-EB01 Evaluation Board Manual
Jumper Settings LEDs
This table gives overview Jumpers Coral evaluation board. sure jumpers according functions want use. Before inserting Coral evaluation board first time, make sure jumpers correctly their default positions. jumpers this table logically grouped according sheet evaluation board schematics.
Jumper Function BUFF1 CONTROL BUFF2 CONTROL Closed Open Closed Open Open Closed Closed Open Description ITU656 Input Buffer manual enable ITU656 Input Buffer enable GPIO (GPCON0) control (default) Enable ITU656 input buffers Disable ITU656 input buffers (default) Input Buffer manual enable Input Buffer enable GPIO (GPCON1) control (default) Enable input buffers Disable input buffers (default) VSYNC enable VSYNC disable (default) Activate blanking Disable blanking (default) Enable Power save mode Disable Power save mode (default) Disable (default) Enable Coral Analog Outputs (default) Analog Outputs Coral Analog Output Override Output Switch (use J250) (default) Coral Analog Output Override Output Switch (use J250) (default) Coral Analog Output Override Output Switch (use J250) (default) Direct Coral HSYNC line (default) HSYNC line driver Direct Coral VSYNC line (default) VSYNC line driver
MANUAL SELECT
MANUAL SELECT
JP300
VSYNC SELECT
J300
BLANK
J301
POWER SAVE
J500 J250
SYNC GREEN Output Switch
JP250
Green Output
JP251
Output
JP252
Blue Output
JP253
HYSNC line driver
JP254
VSYNC line driver
Revision 1.01 2007 Fujitsu Microelectronics Europe
Page
MB86296-EB01 Evaluation Board Manual
Closed Open Closed Open Closed Open Closed Open Closed Open Closed Open 9-10 11-12 Closed Open Closed Open Closed Open Closed Open Closed Open 9-10 Closed Open Closed Open enable disable (default) enable disable (default) enable disable (default) enable disable (default) enable disable (default) enable disable (default) INTA# PRSNT1# (closed default 25W) PRSNT2# (open default 25W) Disable (default) Enable enable Disable (default) 14.32 source (default) Other oscillator settings Other oscillator settings 14.32 source (default) Internal (default) clock Test enable Test enable Test SMCK enable Test enable Test XTST enable 3.3V supply pins enabled (default) (for current measurement only) 1.8V supply pins enabled (default) (for current measurement only)
J201
RGBIR0 enable
J202
RGBIR1 enable
J203
RGBIR2 enable
J204
RGBIR3 enable
J205
RGBIR4 enable
J206
RGBIR5 enable
J151 (1-8)
Interrupt Select (all open default) Board Power Indicator
J151 (9-12)
J152
enable
J100
Reset enable
J101
Coral CLKSEL0 Input
J102
Coral CLKSEL1 Input
J103
Coral CLOCKMODE Input
Test Select (all open default)
Coral 3.3V enable
Coral 1.8V enable
Page
Revision 1.01 2007 Fujitsu Microelectronics Europe
MB86296-EB01 Evaluation Board Manual
J104 J153 JP150 JP501 JP550 J251
Reset Coral Power supply Coral Select 3.3V power supply Enable video (Rev. later) Enable video decoder SAA7113H (Rev. later) Disable analogue switch video output
Open Closed Closed open Closed open Open closed
reset reset Coral supplied with 1.8V 1V8-pin Coral supplied with 1.9V 1V8-pin 3.3V supplied PCI-bus 3.3V generated from onboard voltage regulator enabled disabled Always enabled Controlled GPIO Device enabled Device disabled, jumper should closed, -12V available bus, that case JP250JP252 position
Table Jumper board There further some LEDs board what should show activity status different lines signals. LED1 LED2 LED100 LED150 LED151 LED152 LED153 LED154 LED200 LED201 LED202 LED203 LED204 LED205 Table LEDs board connected GPIO GPIO reset signal voltage 3.3V voltage 1.8V voltage voltage -12V voltage RGBIR0 RGBIR1 RGBIR2 RGBIR3 RGBIR4 RGBIR5 function input buffer enabled ITU656 input buffer enabled reset active voltage available 3.3V voltage available 1.8V voltage available voltage available -12V voltage available used IO-pin used IO-pin used IO-pin used IO-pin used IO-pin used IO-pin
Revision 1.01 2007 Fujitsu Microelectronics Europe
Page
MB86296-EB01 Evaluation Board Manual
Expansion Connectors
There expansion connectors available MB86296-EB01 evaluation board which used access video input output signals well some other signals board extensions. physical locations combination with jumpers J151 allow daughterboard design which mounted evaluation board.
Expansion connector J200 (Video Input Signals)
Page
Revision 1.01 2007 Fujitsu Microelectronics Europe
MB86296-EB01 Evaluation Board Manual
Expansion Connector J207 (Video output signals)
Revision 1.01 2007 Fujitsu Microelectronics Europe
Page
MB86296-EB01 Evaluation Board Manual
Multiplexed Pins Coral
Coral provides number functions which multiplexed different pins. This evaluation board provides multiplexing unit (buffers) most these pins. This section explains which functions used which settings required create dedicated signal routing.
SDRAM Coral actually allows either 32-bit 64-bit SDRAM (see "XRE pin"). order avoid complex high-speed signal buffers order allow complete testing video input facilities note that this board provides only 32-bit SDRAM (XRE fixed logic zero).
Video input Coral number functions multiplexed video input bus. addition, this used evaluation board expand some additional functions (e.g. LEDs, SIO). main signal routing video input controlled GPIO pins GPCON0 GPCON1 alternatively, jumpers. GPCON pins programmed using Coral GPIO registers. Refer example software projects details. Which functions available they selected shown table below:
mode
Function Video inputs disabled
GPCON pins
Description Onboard video input sources routed Coral GPCON0=0 digital video sources input GPCON1=0 expansion connector J200 LEDs used (make sure J201.6 set) Other functions (SIO, GPIOs) used GPCON0=1 ITU656 video routed from video decoder GPCON1=0 (SAA7113) Coral ITU656 video input other functions available GPCON0=0 RGB666 video routed from GPCON1=1 (AD9883) Coral video input other functions available GPCON0=1 Setting prohibited! GPCON1=1
Composite video input
video input
Setting prohibited!
alternative method achieve above settings enable appropriate buffers directly using jumpers (then GPCON0,1 outputs ignored). enable these functions directly, above modes. Make sure enable both buffers simultaneously (mode
Page
Revision 1.01 2007 Fujitsu Microelectronics Europe
MB86296-EB01 Evaluation Board Manual
Memory
MB86296-EB01 evaluation board appears Memory Local Address Space
1000 0000h 11FB FFFFh 11FC 0000h 11FF FFFFh
CORAL Frame Memory CORAL Register Area
32bit 32bit
Local Address Space
Note: details regarding Coral frame register memory area, refer "MB86296 Coral hardware manual
Revision 1.01 2007 Fujitsu Microelectronics Europe
Page
MB86296-EB01 Evaluation Board Manual
Worldwide Headquarters Disclaimer
Japan
Tel: 5322 3353 Fax: 5322 3386 Fujitsu Limited Shinjuku Dai-Ichi Seimei Bldg. 2-7-1, Nishi-shinjuku Shinjuku-ku, Tokyo 163-0721 Japan
Asia Pacific
Tel: 0770 Fax: 0220 Fujitsu Microelectronics Asia Lorong Chauan Tech Park #05-08 Singapore 556741
http://www.fujitsu.com
http://www.fujitsu.com/sg/
Tel: 737-5600 Fax: 737-5999 Fujitsu Microelectronics America Inc. 1250 Arques Avenue, 333, Sunnyvale, 94088-3470
Customer Response Center Mon-Fri 7am-5pm (PST)
Europe
Tel: 6103 6900 Fax:+49 6103 690122 Fujitsu Microelectronics Europe GmbH Pittlerstrasse D-63225 Langen Germany
onics/
contents this document subject change without notice. Customers advised consult with FUJITSU sales representatives before ordering. information circuit diagrams this document presented examples semiconductor device applications, intended incorporated devices actual use. Also, FUJITSU unable assume responsibility infringement patent rights other rights third parties arising from this information circuit diagrams. license granted implication otherwise under patent patent rights Fujitsu Microelectronics GmbH. FUJITSU semiconductor devices intended standard applications (computers, office automation other office equipment, industrial, communications measurement equipment, personal household devices, etc.). CAUTION: Customers considering products special applications where failure abnormal operation directly affect human lives cause physical injury property damage, where extremely high levels reliability demanded (such aerospace systems, atomic energy controls, floor repeaters, vehicle operating controls, medical devices life support, etc.) requested consult with FUJITSU sales representatives before such use. company will responsible damages arising from such without prior approval. semiconductor devices have inherently certain rate failure. must protect against injury, damage loss from such failures incorporating safety design measures into your facility equipment such redundancy, fire protection, prevention over-current levels other abnormal operating conditions. products described this document represent goods technologies subject certain restrictions export under Foreign Exchange Foreign Trade Control Japan, prior authorisation Japanese government should required export those products from Japan.
Page
Revision 1.01 2007 Fujitsu Microelectronics Europe
Other recent searches
TSC691E - TSC691E TSC691E Datasheet
TSC692E - TSC692E TSC692E Datasheet
TSC693E - TSC693E TSC693E Datasheet
TP2435 - TP2435 TP2435 Datasheet
TDA9725 - TDA9725 TDA9725 Datasheet
SUM45N25-58 - SUM45N25-58 SUM45N25-58 Datasheet
SN74AVC126 - SN74AVC126 SN74AVC126 Datasheet
DSX151GA - DSX151GA DSX151GA Datasheet
AU02A - AU02A AU02A Datasheet
Privacy Policy | Disclaimer
© 2012 Datasheet Archive
