PART NUMBER: VHB200W DESCRIPTION: half-brick dc-dc converter
|
|
|
Top Searches for this datasheet
07/2009
PART NUMBER: VHB200W
DESCRIPTION: half-brick dc-dc converter
description
VHB200W series DC-DC converters designed high reliability applications, featuring over-temperature protection, over-current protection. wide input range (10-36V 18-75V) very useful stabilize input source like batteries various discharging charging conditions. Additionally, high efficiency, fast response, tight regulations, remote sense remote On/Off control make these converters very useful many applications.
features
isolated output Compliant input range output short circuit protection on/off protection shutdown standard brick size
MODEL
VHB200W-Q24-S3R3 VHB200W-Q24-S5 VHB200W-Q24-S12 VHB200W-Q24-S15 VHB200W-Q24-S24 VHB200W-Q24-S28 VHB200W-Q24-S48 VHB200W-Q48-S3R3 VHB200W-Q48-S5 VHB200W-Q48-S12 VHB200W-Q48-S15 VHB200W-Q48-S24 VHB200W-Q48-S28 VHB200W-Q48-S48
notes:
input voltage nominal range
output voltage
output current
input current load full load (mA) (mA)
efficiency typ.
10.0~36.0 10.0~36.0 10.0~36.0 10.0~36.0 10.0~36.0 10.0~36.0 10.0~36.0 18.0~75.0 18.0~75.0 18.0~75.0 18.0~75.0 18.0~75.0 18.0~75.0 18.0~75.0
16.7 13.3 16.7 13.3
7900 9580 9710 9670 9540 6720 3125 4682 4744 4723 4716 4730
output derating (page input currents measured hominal input voltage efficiency measured nominal line, full load
INPUT
parameter input voltage range under voltage lockout conditions/description units
remote on/off control input filter
notes:
power power down power (48V output) power down (48V output) power power down section application notes type
suffix model number negative logic on/off control
*V-Infinity reserves right make changes products discontinue product service without notice, advise customers verify most up-todate product information before placing orders. V-Infinity assumes liability responsibility customer's applications using V-Infinity products other than repair replacing V-I's option) V-Infinity products meeting V-I's published specifications. Nothing will covered outside standard product warranty.
20050 112th Ave. Tualatin, Oregon 97062 phone 503.612.2300 503.612.2382
page date
07/2009
PART NUMBER: VHB200W
DESCRIPTION: half-brick dc-dc converter
OUTPUT
parameter voltage accuracy transient response external trim adj. range ripple noise (20MHz conditions/description step load change temperature coefficient short circuit protection continuous line regulation load regulation over voltage protection trip range, nom. over current protection nominal output ±0.03 ±0.2 ±0.2 ±1.5 units %/°C
GENERAL SPECIFICATIONS
parameter switching frequency operating ambient temp. storage temperature thermal shutdown case temp. case material aluminum conditions/description units
ISOLATION SPECIFICATIONS
parameter isolation voltage conditions/description input/output input/case output/case 1500 1500 1500 units
isolation resistance
notes: measured from high line line full load measured from full load zero load nominal input output derating curve (page
*V-Infinity reserves right make changes products discontinue product service without notice, advise customers verify most up-todate product information before placing orders. V-Infinity assumes liability responsibility customer's applications using V-Infinity products other than repair replacing V-I's option) V-Infinity products meeting V-I's published specifications. Nothing will covered outside standard product warranty.
20050 112th Ave. Tualatin, Oregon 97062 phone 503.612.2300 503.612.2382
PART NUMBER: VHB200W
MECHANICAL DRAWING
Dimensions Inches(mm) Tolerances Inches: X.XX= ±0.02 X.XXX= ±0.010 Millimeters: X.X= ±0.5 X.XX= ±0.25 Mounting Inserts BOTTOM VIEW M3*0.5 Through 4pl. Function +Vin ON/OFF CASE -Vin -Vout -Sense Trim +Sense +Vout
20050 112th Ave. Tualatin, Oregon 97062 phone 503.612.2300 503.612.2382 DESCRIPTION: half-brick dc-dc converter
date
page
07/2009
page date
07/2009
PART NUMBER: VHB200W
DESCRIPTION: half-brick dc-dc converter
APPLICATION NOTES
OUTPUT DE-RATING operating case temperature range VHB200W +100°C. When operating VHB200W series, proper derating cooling needed. maximum case temperature under operating condition should exceed 100°C.
Power Dissipated Ambient Temperature
Natural Convection ft./min. (0.1 m/s) ft./min. (0.5 m/s)
Power Disspated ,Pd(Watts)
ft./min. (1.0 m/s) ft./min. (1.5 m/s) ft./min. (2.0 m/s) ft./min. (2.5 m/s) ft./min. (3.0 m/s) ft./min. (3.5 m/s) ft./min. (4.0 m/s)
Ambient Temperature ,Ta(Deg.
FIGURE OUTPUT DERATING (FORCED CONVECTION WITH HEAT SINK)
Example: What minimum airflow necessary VHB200W-Q48-S12 operating nominal line, output current 16.7 maximum ambient temperature 40°C? Solution: Given: Vin=48 Vo=12 Io=16.7 Determine Power dissipation (Pd): Pd=Pi-Po=Po(1-)/ Determine airflow: Given: Pd=27.32 Ta=40°C Check above Power de-rating curve: minimum airflow= ft./min. Verifying:
FLOW RATE Natural Convection 20ft./min. (0.1m/s) ft./min. (0.5m/s) ft./min. (1.0m/s) ft./min. (1.5m/s) ft./min. (2.0m/s) ft./min. (2.5m/s) ft./min. (3.0m/s) ft./min. (3.5m/s) ft./min. (4.0m/s)
TYPICAL 7.12 6.21 5.17 4.29 3.64 2.96 2.53 2.37 2.19
Chart Thermal Resistance Flow
maximum temp. rise maximum case temperature Tc=Ta+T=99.83°C<100°C Where: thermal resistance from case ambience.The ambient temperature case temperature.
20050 112th Ave. Tualatin, Oregon 97062 phone 503.612.2300 503.612.2382
page date
07/2009
PART NUMBER: VHB200W
DESCRIPTION: half-brick dc-dc converter
INPUT VOLTAGE RANGE important ensure input voltage measured converter input pins within range that converter. Make sure wire losses voltage ripples accounted for. possible problem driving converter with linear unregulated power supply. example, average voltage measured with voltage ripple 3Vpp, actual input swing from 7.5V 10.5V. This will outside specified input range 10~36V converter function properly. other end, make sure actual input voltage does exceed highest voltage or75V.
LEAD WIRES Make sure input output wires adequate size minimize voltage drop, ensure voltage across input terminals above converter's rated minimum voltage times. recommended have wire pairs twisted, respectively input pair output pair, minimize noise pickup.
INPUT CURRENT input voltage source must able provide enough current converter, otherwise start operate properly. typical symptom starting unusually output voltage. general, recommended able provide least: Ipeak 150%*Pout/( *Vmin) where Pout maximum output power, Vmin minimum input voltage converter's efficiency. example, VHB200W-Q24-S5 operate with 10~36 input, output efficiency 87%, minimum source current recommended Ipeak 150% (87% 34.48
INPUT FUSE limit input current facilitate input reversal protection input protection, fast-acting input fuse recommended input line. fuse rating will depend input range should allow maximum current lowest input volt age, shown this equation: Ipeak 150%*Pout/( *Vmin). previous example VHB200W-Q24-S5, peak input current calculated 34.48 fuse suitable this application. Make sure fuse voltage rating higher than maximum input voltage.
REMOTE SENSE converter provides regulated outputs output terminals. When there large current and/or output cable some length, voltage output cable noticeably lower than terminals. converter compensate 0.5V voltage drop through remote sense terminals. ensure accurate regulation, separate wires (twisted) from desired regulation points remote sense terminals, shown below.
Trim
FIGURE REMOTE SENSE
Load
20050 112th Ave. Tualatin, Oregon 97062 phone 503.612.2300 503.612.2382
page date
07/2009
PART NUMBER: VHB200W
DESCRIPTION: half-brick dc-dc converter
OUTPUT TRIMMING (OPTIONAL) output voltages preset nominal values indicated models table factory. desired, output voltage optionally trimmed different value (+/- 10%) with external resistors and/or potentiometer shown below. Care should taken ensure that maximum ouput power module remains below maximum rated power (Maximum rate power o,set o,max).
+Vin
Trimpot 470K load
FIGURE TRIMMING WITH EXTERNAL POTENTIOMETER
Trim -Vin
trim output voltage with fixed resistors, output voltage calculated follows.
Trim-Down
+Vin Trim
trim-down load
Trim-Up
+Vin
trim-up
Trim -Vin
load
-Vin
FIGURE TRIM-DOWN VOLTAGE SETUP value trim-down defined
FIGURE TRIM-UP VOLTAGE SETUP value trim-up defined
Rtrim-down
Vo,nom Vo,nom
Rtrim-up
A(Vo)(100+%) 1.225 Vo,nom Vo,nom
Where: trim-down external resistor o,nom nominal output voltage. desired output voltage. values defined Table example, trimdown module (VHB200W-Q24-S24) 22.08V, trim-down calculated:
Where: trim-up external resistor o,nom nominal output voltage. desired output voltage. values defined Table example, trimdown module (VHB200W-Q24-S24) 25.92V, trim-up calculated:
511, 10.22 Rtrim-down 10.22 Rtrim-up
5.11, 511, 10.22 (25.92) (100 10.22 1.225 Rtrim-up 1476.55
Output Voltage(V) 5.11 2000 10.22
Rtrim-down 53.66
Table
20050 112th Ave. Tualatin, Oregon 97062 phone 503.612.2300 503.612.2382
page date
07/2009
PART NUMBER: VHB200W
DESCRIPTION: half-brick dc-dc converter
OUTPUT SHORT-CIRCUIT PROTECTION Output overload short circuit conditional will cause output voltage decline shutdown altogether. case temperature
over 110°C, output recovers automatically when short conditions removed. case slight overloading, output voltage shut down, converter build heat over time, causing over-temperature shutdown.
OVER-TEMPERATURE PROTECTION When case temperature reaches about 110°C, converter's built-in protection circuit will shut down output. When temperature reduced enough safe operating level, converter will recover normal operations automatically.
OUTPUT case output voltage exceeds threshold, converter shuts down.
OUTPUT PARALLEL CONNECTIONS converter designed load share output. However, redundancy, outputs more converters connected parallel through OR-ing diodes, shown below.
+Vin
-Vin
FIGURE OUTPUT PARALLEL CONNECTIONS
+Vin
-Vin
OUTPUT SERIES CONNECTIONS more converters connected series obtain higher output voltage. prevent output reverse biasing each other case short, Schottky diode each output reverse polarity, shown diagram. event short, converters will forward-bias diodes output reversal will limited diode drop (about 0.5V) only, damage converters. forward current will cause each converter into short-circuit protection. proper diode selection, make
sure that: diodes voltage rating higher than each converter output; rated diode current carry short-circuit current; diodes overheat before short removed.
+Vin
-Vin
FIGURE OUTPUT SERIES CONNECTIONS
+Vin
-Vin
20050 112th Ave. Tualatin, Oregon 97062 phone 503.612.2300 503.612.2382
page date
07/2009
PART NUMBER: VHB200W
DESCRIPTION: half-brick dc-dc converter
REMOTE OUTPUT ON/OFF CONTROL converter output enabled disabled through On/Off pin. control logic shown this table. common control circuit shown below.
(pin
High signal here disable output
-Vin
-Vin (pin
FIGURE REMOTE ON/OFF CONTROL WITH TRANSISTOR SWITCH
FIGURE REMOTE ON/OFF CONTROL
Logic Table Negative logic Closed <0.8 Output Open >2.4 Output
ISOLATION
Positive logic Output Output
input output converter electrically isolated. needed, output terminal connected input terminal, resulting converter non-isolated.
INPUT FILTERING INTERFERENCE VHB200W converters have input capacitors that control input current ripple associated interference. However, been tested formal standard conducted emissions. Additional filtering needed ensure compliance standard. Refer FIGURE reference circuit.
20050 112th Ave. Tualatin, Oregon 97062 phone 503.612.2300 503.612.2382
page date
07/2009
PART NUMBER: VHB200W
DESCRIPTION: half-brick dc-dc converter
INPUT FILTERING INTERFERENCE VHB200W converters have input capacitors that control input current ripple associated interference. However, they have been tested formal standard conducted emissions. Additional filtering needed ensure compliance standard. Refer FIGURE reference circuit.
-Vin +Vin
Rload
CASE
FIGURE FILTER VHB200W
Model VHB200W-Q24-S5 VHB200W-Q24-S12 VHB200W-Q24-S24 VHB200W-Q24-S28 VHB200W-Q24-S28 VHB200W-Q24-S48 VHB200W-Q24-S48 VHB200W-Q48-S5 VHB200W-Q48-S12 VHB200W-Q48-S24 VHB200W-Q48-S28 VHB200W-Q48-S28 VHB200W-Q48-S48 VHB200W-Q48-S48
Class Class Class Class Class Class Class Class Class Class Class Class Class Class
82uF/100V 82uF/100V 120uF/100V 100uF/100V 120uF/100V 100uF/100V 82uF/100V 82uF/100V 120uF/100V 120uF/100V 150uF/100V 120uF/100V 100uF/100V 82uF/100V
82uF/100V 82uF/100V 120uF/100V 100uF/100V 120uF/100V 100uF/100V 82uF/100V 82uF/100V 120uF/100V 120uF/100V 150uF/100V 120uF/100V 100uF/100V 82uF/100V
10uF/50V 2220 10uF/50V 2221 10uF/50V 2220 470uF/100V 100uF/100V 4.7uF/100V 2220 4.7uF/100V 2220 4.7uF/100V 2220 4.7uF/100V 2220 470uF/100V 100uF/100V 4.7uF/100V 2220
1000pF/2KV 1000pF/2KV 1000pF/2KV 680pF/2KV 1000pF/2KV 1000pF/2KV 1500pF/2KV 1000pF/2KV 680pF/2KV 2200pF/2KV
1000pF/2KV 1000pF/2KV 1000pF 680pF/2KV 1000pF/2KV 680pF/2KV 680pF/2KV 680pF/2KV 680pF/2KV 2200pF/2KV
0.5mH 0.5mH 0.5mH 0.5mH 0.45mH 1.0mH 0.45mH 0.5mH 0.5mH 0.5mH 0.5mH 0.45mH 1.0mH 0.45mH
1000pF/2KV 680pF/2KV 1000pF/2KV
680pF/2KV 680pF/2KV 680pF/2KV
NOTE: recommended components starting point guaranteed meeting requirements. More less filtering required specific application meet other standards.
20050 112th Ave. Tualatin, Oregon 97062 phone 503.612.2300 503.612.2382
page date
07/2009
PART NUMBER: VHB200W
DESCRIPTION: half-brick dc-dc converter
OUTPUT FILTERING converter built-in capacitors output control ripple noise. desired, additional output capacitance introduced input powered equipment. Recommended starting point: tantalum ceramic capacitor parallel output.
OUTPUT NOISE MEASUREMENT SCHEMATIC proper output ripple noise measurement, connect tantalum ceramic capacitor across output. scope bandwidth 20MHz. Probe directly capacitors, using small ground clip minimize measurement error.
+Vin
Trim
Ceramic 1.0µF
Resistor Load
-Vin
Solid Tantalum 10µF Scope
FIGURE OUTPUT NOISE MEASUREMENT CIRCUIT
20050 112th Ave. Tualatin, Oregon 97062 phone 503.612.2300 503.612.2382
Other recent searches
TIP29A - TIP29A TIP29A Datasheet
TIP30A - TIP30A TIP30A Datasheet
SSM4409GEM - SSM4409GEM SSM4409GEM Datasheet
P83C524 - P83C524 P83C524 Datasheet
P80C528 - P80C528 P80C528 Datasheet
P83C528 - P83C528 P83C528 Datasheet
ML145145 - ML145145 ML145145 Datasheet
MC145145-2 - MC145145-2 MC145145-2 Datasheet
DSE-175-029 - DSE-175-029 DSE-175-029 Datasheet
BX8214V - BX8214V BX8214V Datasheet
1982800000 - 1982800000 1982800000 Datasheet
Privacy Policy | Disclaimer
© 2012 Datasheet Archive
