v03.0809 400° ANALOG PHASE SHIFTER HMC247 ideal for: Fiber O

The Datasheet Archive - 100 Million Datasheets from 7500 Manufacturers.

v03.0809 400° ANALOG PHASE SHIFTER HMC247 ideal for: Fiber O

Datasheet Thumbnail

Top Searches for this datasheet

HMC247
v03.0809
400° ANALOG PHASE SHIFTER
HMC247 ideal for: Fiber Optics
Features
Wide Bandwidth: Phase Shift: >400° Single Positive Voltage Control Small Size:
PHASE SHIFTERS ANALOG CHIP
Military Test Equipment
Functional Diagram
General Description
HMC247 Analog Phase Shifter which controlled analog control voltage from +10V. HMC247 provides continuously variable phase shift degrees GHz, degrees GHz, with consistent insertion loss versus phase shift. phase shift monotonic with respect control voltage. control port modulation bandwidth MHz. insertion loss compact size enable this part used wide range applications, including phase adjustment clocks fiber optic systems test equipment. data measured with chip test fixture, connected 0.076 mil) ribbon bonds minimal length <0.31 (<12 mils).
Electrical Specifi cations, +25° System
Parameter Phase Shift Range: Frequency (GHz) Min. Typ. Max. Units degrees degrees degrees Volt /Volt
Insertion Loss Return Loss (Input Output) Control Voltage Range Modulation Bandwidth Phase Voltage Sensitivity Insertion Phase Temperature Sensitivity
price, delivery, place orders, please contact Hittite Microwave Corporation: Alpha Road, Chelmsford, 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line www.hittite.com
HMC247
v03.0809
400° ANALOG PHASE SHIFTER
Insertion Loss Control Voltage
Phase Shift Control Voltage
NORMALIZED PHASE SHIFT (degrees)
INSERTION LOSS (dB)
+25C +85C -55C
PHASE SHIFTERS ANALOG CHIP
Vctl
Vctl
Phase Shift Frequency Vctl (Relative Vctl
NORMALIZED PHASE SHIFT (degrees) FREQUENCY (GHz)
+25C +85C -55C
Insertion Loss Frequency
INSERTION LOSS (dB) FREQUENCY (GHz)
Input Return Loss Frequency, Vctl +10V
Output Return Loss Frequency, Vctl +10V
RETURN LOSS (dB)
RETURN LOSS (dB)
FREQUENCY (GHz)
FREQUENCY (GHz)
price, delivery, place orders, please contact Hittite Microwave Corporation: Alpha Road, Chelmsford, 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line www.hittite.com
HMC247
v03.0809
400° ANALOG PHASE SHIFTER
Second Harmonics Control Voltage,
Input Control Voltage
(dBm)
PHASE SHIFTERS ANALOG CHIP
HARMONICS (dBc)
Vctl Vctl
Insertion Loss
Insertion Loss
INSERTION LOSS (dB)
INSERTION LOSS (dB)
INPUT POWER (dBm)
INPUT POWER (dBm)
Insertion Loss
Phase Shift
NORMALIZED PHASE SHIFT (degrees)
INSERTION LOSS (dB)
INPUT POWER (dBm)
INPUT POWER (dBm)
price, delivery, place orders, please contact Hittite Microwave Corporation: Alpha Road, Chelmsford, 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line www.hittite.com
HMC247
v03.0809
400° ANALOG PHASE SHIFTER
Phase Shift
NORMALIZED PHASE SHIFT (degrees)
Phase Shift
NORMALIZED PHASE SHIFT (degrees)
-0.1
-0.1
-0.3
-0.3
-0.5
-0.5
INPUT POWER (dBm)
INPUT POWER (dBm)
Absolute Maximum Ratings
Control Voltage (Vctl) Reverse Current Input Power (RFin) Channel Temperature (Tc) Continuous Pdiss (derate mW/°C above Thermal Resistance (junction bottom) Storage Temperature Operating Temperature 1.83 35.6 °C/W +150
price, delivery, place orders, please contact Hittite Microwave Corporation: Alpha Road, Chelmsford, 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line www.hittite.com
PHASE SHIFTERS ANALOG CHIP
HMC247
v03.0809
400° ANALOG PHASE SHIFTER
Assembly Diagram
PHASE SHIFTERS ANALOG CHIP
Descriptions
Number Function RFIN Description Port blocked. Interface Schematic
Vctl
Phase shift control pin. Application voltage between volts causes transmission phase change. equivalent circuit series connected diode resistor
RFOUT
Port blocked.
backside must connected ground.
price, delivery, place orders, please contact Hittite Microwave Corporation: Alpha Road, Chelmsford, 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line www.hittite.com
HMC247
v03.0809
400° ANALOG PHASE SHIFTER
Outline Drawing
PHASE SHIFTERS ANALOG CHIP
Packaging Information
Standard WP-4 (Waffle Pack)
DIMENSIONS INCHES [MM] UNLABLED BOND PADS GROUND. THICKNESS .004" TYPICAL BOND .004" SQUARE. BACKSIDE METALIZATION: GOLD. BOND METALIZATION: GOLD.
Alternate
Refer "Packaging Information" section packaging dimensions. alternate packaging information contact Hittite Microwave Corporation.
Handling Precautions
Follow these precautions avoid permanent damage. Storage: bare placed either Waffle based protective containers, then sealed protective shipment. Once sealed protective been opened, should stored nitrogen environment. Cleanliness: Handle chips clean environment. attempt clean chip using liquid cleaning systems. Static Sensitivity: Follow precautions protect against strikes. Transients: Suppress instrument bias supply transients while bias applied. shielded signal bias cables minimize inductive pick-up. General Handling: Handle chip along edges with vacuum collet with sharp pair bent tweezers. surface chip fragile bridges should touched with vacuum collet, tweezers, fingers.
Mounting
chip back-metallized mounted with electrically conductive epoxy. mounting surface should clean Epoxy Attach: Apply minimum amount epoxy mounting surface that thin epoxy fillet observed around perimeter chip once placed into position. Cure epoxy manufacturer's schedule.
Wire Bonding
Ball wedge bond with 0.025mm mil) diameter pure gold wire. Thermosonic wirebonding with nominal stage temperature deg. ball bonding force grams wedge bonding force grams recommended. minimum level ultrasonic energy achieve reliable wirebonds. Wirebonds should started chip terminated package substrate. bonds should short possible <0.31mm mils).
price, delivery, place orders, please contact Hittite Microwave Corporation: Alpha Road, Chelmsford, 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line www.hittite.com

v03.0809 400° ANALOG PHASE SHIFTER HMC247 ideal for: Fiber O

Top Searches for this datasheet

Other recent searches