WM8990 highly integrated ultra-low power hi-fi codec designed handsets
|
|
|
Top Searches for this datasheet
Mobile Multimedia CODEC with Dual-Mode Class AB/D Speaker Driver
WM8990 highly integrated ultra-low power hi-fi codec designed handsets rich multimedia features such mobile digital audio playback gaming. Ultra-low power noise interfaces many other audio components system provided. powerful speaker driver operate class modes, providing total flexibility system designer. leakage, high PSRR pop/click suppression enable direct battery connection speaker supply. very highly flexible input configuration supports multiple microphone line inputs (mono stereo, single-ended differential). Four headphone drivers support fully differential headset drive, providing excellent crosstalk performance bass response, maximising stereo effects, allowing removal large expensive headphone capacitors. Stereo 24-bit sigma-delta ADCs DACs provide hi-fi quality audio record playback, with flexible digital audio interface supporting most commonly-used clocking schemes. integrated power PLL, alternative interface support provide additional flexibility. WM8990 supplied very small thin 42-ball WCSP package, ideal portable systems.
WM8990
FEATURES
99dB (`A' weighted), -84dB 48kHz, 3.3V 94dB (`A' weighted), -82dB 48kHz, 3.3V Microphone interface four differential microphones) Speaker driver into speaker <0.1% 80dB PSRR @217Hz <1uA leakage with direct battery connection Software-selectable class mode Filterless connection supported Pop/Click suppression Headphone speaker drivers 40mW output power into 3.3V Fully differential capless modes supported Pop/Click suppression Mono stereo differential line outputs Powerful GPIO functions Ultra-low power consumption 8.3mW analogue voice call 13.7mW playback headphones On-chip provides flexible clocking scheme Sample rates: 11.025, 22.05, 44.1, 48kHz 42-ball W-CSP package (3.226x3.44x0.7mm, 0.5mm pitch)
APPLICATIONS
Multimedia phones
WOLFSON MICROELECTRONICS
receive regular email updates, sign
Production Data, March 2009,
Copyright ©2009 Wolfson Microelectronics
WM8990 TABLE CONTENTS
Production Data
DESCRIPTION FEATURES. APPLICATIONS TABLE CONTENTS BLOCK DIAGRAM CONFIGURATION ORDERING INFORMATION DESCRIPTION ABSOLUTE MAXIMUM RATINGS RECOMMENDED OPERATING CONDITIONS THERMAL PERFORMANCE SPEAKER POWER DE-RATING CURVE ELECTRICAL CHARACTERISTICS TERMINOLOGY TYPICAL POWER CONSUMPTION SPEAKER DRIVER PERFORMANCE HEADPHONE DRIVER PERFORMANCE. PSRR PERFORMANCE AUDIO SIGNAL PATHS SIGNAL TIMING REQUIREMENTS
SYSTEM CLOCK TIMING AUDIO INTERFACE TIMING MASTER MODE AUDIO INTERFACE TIMING SLAVE MODE AUDIO INTERFACE TIMING MODE CONTROL INTERFACE TIMING 2-WIRE MODE CONTROL INTERFACE TIMING 3-WIRE MODE CONTROL INTERFACE TIMING 4-WIRE MODE
INTERNAL POWER RESET CIRCUIT DEVICE DESCRIPTION
INTRODUCTION. INPUT SIGNAL PATH ANALOGUE DIGITAL CONVERTER (ADC) DIGITAL MIXING DIGITAL ANALOGUE CONVERTER (DAC) OUTPUT SIGNAL PATH ANALOGUE OUTPUTS THERMAL SHUTDOWN GENERAL PURPOSE INPUT/OUTPUT DIGITAL AUDIO INTERFACE DIGITAL AUDIO INTERFACE CONTROL CLOCKING SAMPLE RATES CONTROL INTERFACE POWER MANAGEMENT SUPPRESSION CONTROL. POWER DOMAINS
REGISTER MAP.
REGISTER BITS ADDRESS
March 2009,
Production Data
WM8990
DIGITAL FILTER CHARACTERISTICS
FILTER RESPONSES HIGH PASS FILTER RESPONSES FILTER RESPONSES DE-EMPHASIS FILTER RESPONSES
APPLICATIONS INFORMATION
RECOMMENDED EXTERNAL COMPONENTS.
PACKAGE DIMENSIONS IMPORTANT NOTICE
ADDRESS:
March 2009,
WM8990
LONMIX
Mixer Mixer
Line Inverted
0dB, -6dB
Line
INPUT PGAs
Record Mixer
INPUT MIXERS
LOPMIX
Left Line Input Speaker Voice Left Line Input Left Output Mixer Left Left Bypass Mixer LIN3
-12dB +6dB
-12dB +6dB MONO
RXVOICE AINLMUX
-73dB +6dB, steps
DIFFINL
-12dB +6dB
-12dB +6dB
RXVOICE AINRMUX
-71.625dB +17.625dB, 0.375dB steps
DIFFINR
Bypass Bypass LIN3 RIN3 -12dB 0dB, steps Right Bypass Right Right Line Input Right Output Mixer Voice Right Line Input Speaker Record
-16.5dB +30dB, 0.75dB steps
MICBIAS Current Detect
MICBIAS AVDD DCVDD
A-law u-law support Support Alternative Interface Button Control Accessory Detect Clock Output
RIN1 RIN2
RIN3/GPI8 RIN4/RXP
RIN34
-12dB +6dB
-16.5dB +30dB, 0.75dB steps
-12dB +6dB
RIN12
VREF Inverted Mixer Mixer
250k
250k
LIN3/GPI7 LIN4/RXN
Bypass Bypass
LIN1 LIN2
RIN3
BLOCK DIAGRAM
OUTPUT MIXERS
OUT3MIX
0dB, -6dB
-16.5dB +30dB, 0.75dB steps
OUT3
LIN12
-12dB +6dB
-16.5dB +30dB, 0.75dB steps
-12dB +6dB
0dB, +30dB
0dB, +30dB
DIGITAL CORE
INMIXL
-71.625dB +17.625dB, 0.375dB steps -36dB 0dB, steps
-73dB +6dB, steps
LOPGA
LADC bypass LIN2 Mixer
LOUT
LIN34
-12dB 0dB, steps
-71.625dB 0dB, 0.375dB steps
SPKMIX SPKPGA
-73dB +6dB, steps
HIGH PASS FILTER (Voice Hi-Fi)
LOMIX
1.27x, 1.4x, 1.52x, 1.67x 1.8x Mixer
RIN2 RADC bypass 0dB, -6dB, -12dB
SPKN SPKP
ROMIX
-73dB +6dB, steps
0dB, +30dB 0dB, +6dB, +12dB, +18dB
INMIXR
HIGH PASS FILTER (Voice Hi-Fi)
-71.625dB 0dB, 0.375dB steps
1xVMID, 1.27xVMID, 1.4xVMID, 1.52xVMID, 1.67xVMID 1.8xVMID
ROPGA
-73dB +6dB, steps
ROUT
0dB, +30dB
Mixer
OUT4 OUT4MIX
0dB, -6dB
Mixer
ROPMIX
0dB, -6dB Line
DIGITAL AUDIO INTERFACE GPIO
Line
RONMIX
SYSCLK
CONTROL INTERFACE
VMID
AGND BCLK DGND DCVDD DBVDD HPVDD HPGND DACDAT ADCDAT DACLRC SPKVDD SPKGND ADCLRC/GPIO1
AVDD
CSB/ADDR SDIN SCLK MODE
MCLK
GPIO5/DACDAT2 GPIO4/DACLRC2 GPIO3/BCLK2
March 2009,
Production Data
Production Data
WM8990
CONFIGURATION
ORDERING INFORMATION
ORDER CODE WM8990ECS/RV Note: Reel quantity 3500 TEMPERATURE RANGE -40°C +85°C PACKAGE 42-ball W-CSP (Pb-free, Tape reel) MOISTURE SENSITIVITY LEVEL MSL3 PEAK SOLDERING TEMPERATURE 260°C
March 2009,
WM8990 NAME MICBIAS LIN1 LIN2 LIN3 GPI7 LIN4 RIN1 RIN2 RIN3 GPI8 RIN4 DCVDD DGND DBVDD AVDD AGND HPVDD HPGND SPKVDD SPKGND MCLK BCLK DACLRC DACDAT ADCLRC GPIO1 ADCDAT MODE ADDR SCLK SDIN SPKP SPKN LOUT ROUT OUT3 OUT4 TYPE Analogue Output Analogue Input Analogue Input Analogue Input Digital Input Analogue Input Microphone bias Left channel single-ended input Left channel negative differential input Left channel line input Left channel positive differential input Left channel line input Left channel negative differential input Accessory button detect input Left channel line input Left channel positive differential input Mono differential negative input voice Right channel single-ended input Right channel negative differential input Right channel line input Right channel positive differential input Right channel line input Right channel negative differential input Accessory button detect input Left channel line input Left channel positive differential input Mono differential positive input voice Digital core supply
Production Data
Analogue Input Analogue Input Analogue Input Digital Input Analogue Input
Supply Supply Supply Supply Supply Supply Supply Supply Supply Digital Input Digital Input Output Digital Input Output Digital Input Digital Input Output Digital Output Digital Input Digital Input Digital Input Digital Input Output Analogue Output Analogue Output Analogue Output Analogue Output Analogue Output Analogue Output Analogue Output Analogue Output Analogue Output Analogue Output
Digital ground (Return path both DCVDD DBVDD) Digital buffer (I/O) supply Analogue supply Analogue ground (Return path AVDD) Headphone supply Headphone ground (Return path HPVDD) Supply speaker driver Ground speaker driver (Return path from SPKVDD) Master clock Audio interface clock Audio interface left right clock digital audio data Audio interface left right clock GPIO1 digital audio data Selects 2-wire -wire control -wire chip select 2-wire address select Control interface clock input Control interface data input 2-wire acknowledge output Speaker positive output Speaker negative output Left headphone output Right headphone output Inverted left headphone output Mono inverted output Inverted right headphone output Mono non-inverted output Negative left line output Positive right line output Positive left line output Negative right line output Positive left line output Positive right line output March 2009,
Production Data NAME VMID GPIO3 BCLK2 GPIO4 DACLRC2 GPIO5 DACDAT2 TYPE Analogue Output Digital Input Output Digital Input Output Digital Input Output DESCRIPTION Midrail voltage decoupling capacitor Alternative BCLK GPIO Alternative DACLRC GPIO Alternative DACDAT GPIO
WM8990
March 2009,
WM8990 ABSOLUTE MAXIMUM RATINGS
Production Data
Absolute Maximum Ratings stress ratings only. Permanent damage device caused continuously operating beyond these limits. Device functional operating limits guaranteed performance specifications given under Electrical Characteristics test conditions specified. Sensitive Device. This device manufactured CMOS process. therefore generically susceptible damage from excessive static voltages. Proper precautions must taken during handling storage this device. Wolfson tests package types according IPC/JEDEC J-STD-020B Moisture Sensitivity determine acceptable storage conditions prior surface mount assembly. These levels are: MSL1 unlimited floor life <30°C Relative Humidity. normally stored moisture barrier bag. MSL2 storage year <30°C Relative Humidity. Supplied moisture barrier bag. MSL3 storage hours <30°C Relative Humidity. Supplied moisture barrier bag. Moisture Sensitivity Level each package type specified Ordering Information. CONDITION Supply voltages (excluding SPKVDD) SPKVDD Voltage range digital inputs Voltage range analogue inputs Operating temperature range, Junction temperature, TJMAX Storage temperature after soldering -0.3V -0.3V DGND -0.3V AGND -0.3V +4.5V DBVDD +0.3V AVDD +0.3V
RECOMMENDED OPERATING CONDITIONS
PARAMETER Digital supply range (Core) Digital supply range (Buffer) Analogue supplies range Speaker supply range Ground Notes Analogue, digital speaker grounds must always within 0.3V each other. digital analogue supplies completely independent from each other (i.e. internally connected). DCVDD must less than equal AVDD. DCVDD must less than equal DBVDD. AVDD must less than equal SPKVDD. SPKVDD must high enough support peak output voltage when using DCGAIN ACGAIN functions, avoid output waveform clipping. Peak output voltage AVDD*(DCGAIN+ACGAIN)/2. HPVDD must equal AVDD SYMBOL DCVDD DBVDD AVDD, HPVDD SPKVDD DGND, AGND, HPGND, SPKGND 1.71 1.71 UNIT
March 2009,
Production Data
WM8990
THERMAL PERFORMANCE
Thermal analysis should performed intended application prevent WM8990 from exceeding maximum junction temperature. Several contributing factors affect thermal performance most notably physical properties mechanical enclosure, location device relation surrounding components number layers. Connecting balls through thermal vias into large ground plane will heat extraction. Three main heat transfer paths exist surrounding illustrated below Figure Package (radiation). Package bottom (radiation). Package balls (conduction).
Figure Heat Transfer Paths
temperature rise given power dissipated device. thermal resistance from junction ambient temperature therefore measure heat transfer from surrounding air. determined with reference JEDEC standard JESD51-9.
junction temperature given +TR, where ambient temperature.
PARAMETER Operating temperature range Operating junction temperature Thermal Resistance
SYMBOL
UNIT °C/W
March 2009,
WM8990 SPEAKER POWER DE-RATING CURVE
Production Data
speaker driver been designed drive maximum into with supply. However, thermal restrictions defined W-CSP package limit amount power that safely dissipated device without exceeding maximum operating junction temperature. Power dissipated device correlates directly with speaker efficiency, hence there separate de-rating curves class class operation. Under circumstances should recommended maximum powers exceeded.
CLASS DE-RATING CURVES
de-rating curves shown Figure based full scale sinusoidal input.
SPKVDD 3.6V SPKVDD 3.3V SPKVDD 5.5V SPKVDD SPKVDD 4.2V
SPKVDD SPKVDD 2.7V
Figure Class Speaker Power De-Rating Curve
March 2009,
Production Data
WM8990
CLASS DE-RATING CURVE
de-rating curves shown Figure based full scale sinusoidal input
SPKVDD 3.6V SPKVDD 3.3V SPKVDD 5.5V SPKVDD SPKVDD 4.2V
SPKVDD SPKVDD 2.7V
Figure Class Speaker Power De-Rating Curve
March 2009,
WM8990 ELECTRICAL CHARACTERISTICS
Test Conditions DCVDD 1.8V, DBVDD 3.3V, AVDD HPVDD 3.3V, SPKVDD +25oC, 1kHz signal, 48kHz, gain 0dB, 24-bit audio data unless otherwise stated. PARAMETER Maximum Full-Scale Input Signal Level Note This changes proportion AVDD (AVDD/3.3). Note When mixing input outputs line inputs total signal must exceed 1Vrms (0dBV). Note 1.0Vrms differential signal equates 0.5Vrms/-6dBV input. Maximum Full-Scale Line Input Signal Level Note This changes proportion AVDD (AVDD/3.3). Note When mixing line inputs, input outputs outputs total signal must exceed 1Vrms (0dBV). Note 1.0Vrms differential signal equates 0.5Vrms/-6dBV input. Line input LIN2 RIN2 SPKMIX TEST CONDITIONS Single-ended input LIN1, LIN3, RIN1 RIN3, output INMIXL INMIXR Differential input LIN1/LIN2, LIN3/LIN4, RIN1/RIN2 RIN3/RIN4, output INMIXL INMIXR Differential input single-ended inputs LIN1/LIN3 RIN1/RIN3, output DIFFINL DIFFINR
Production Data
UNIT Vrms
Analogue Input Maximum Signal Levels (LIN1, LIN2, LIN3, LIN4, RIN1, RIN2, RIN3, RIN4)
Vrms
Vrms
Line input LIN2, LIN4, RIN2 RIN4 INMIXL INMIXR
Vrms
Vrms
Line input LIN3 RIN3 LOMIX ROMIX
Vrms
Differential mono line input RXP/RXN RXVOICE
Vrms
Differential mono line input RXP/RXN differential output OUT3/OUT4
Vrms
March 2009,
Production Data
WM8990
Test Conditions DCVDD 1.8V, DBVDD 3.3V, AVDD HPVDD 3.3V, SPKVDD 1kHz signal, 48kHz, gain 0dB, 24-bit audio data unless otherwise stated. PARAMETER Input Resistance Note: this will seen parallel with resistance other enabled input paths from same TEST CONDITIONS LIN1, LIN3, RIN1 RIN3 (PGA Gain -16.5dB) LIN1, LIN3, RIN1 RIN3 (PGA Gain 0dB) LIN1, LIN3, RIN1 RIN3 (PGA Gain +30dB) LIN2, LIN4, RIN2 RIN4 (Constant gains) UNIT
Analogue Input Impedances (LIN1, LIN2, LIN3, LIN4, RIN1, RIN2, RIN3, RIN4)
Line Input Resistance Note: this will seen parallel with resistance other enabled input paths from same
LIN2 RIN2 INMIXL INMIXR (-12dB) LIN2 RIN2 INMIXL INMIXR (0dB) LIN2 RIN2 INMIXL INMIXR (+6dB) LIN2 RIN2 SPKMIX (SPKATTN 0dB) LIN2 RIN2 SPKMIX (SPKATTN -12dB) LIN3 RIN3 LOMIX ROMIX (0dB) LIN3 RIN3 LOMIX ROMIX (-21dB) RXVOICE AINLMUX AINRMUX (Gain +6dB) RXVOICE AINLMUX AINRMUX (Gain 0dB) RXVOICE AINLMUX AINRMUX (Gain -12dB) RXVOICE AINLMUX AINRMUX (Gain +6dB) RXVOICE AINLMUX AINRMUX (Gain 0dB) RXVOICE AINLMUX AINRMUX (Gain -12dB) LIN4 OUT3 RIN4 OUT4 (Gain -6dB) LIN4 OUT3 RIN4 OUT4 (Gain 0dB)
Input Capacitance
analogue input pins
March 2009,
WM8990
Test Conditions DCVDD 1.8V, DBVDD 3.3V, AVDD HPVDD 3.3V, SPKVDD +25oC, 1kHz signal, 48kHz, gain 0dB, 24-bit audio data unless otherwise stated. PARAMETER Minimum Programmable Gain Maximum Programmable Gain Programmable Gain Step Size Mute Attenuation Common Mode Rejection Ratio (1kHz input) Guaranteed monotonic Inputs disconnected Single differential mode, gain +30dB Single differential mode, gain Single differential mode, gain -16.5dB Differential input DIFFINL DIFFINR LIN1/LIN3 RIN1/RIN3, gain Received Voice (RXP-RXN) Differential Single-Ended Converter RXVOICE Minimum Programmable Gain Maximum Programmable Gain Programmable Gain Step Size Mute Attenuation Fixed Gain Mute Attenuation Minimum Programmable Gain Maximum Programmable Gain Programmable Gain Step Size Minimum Programmable Gain Maximum Programmable Gain Programmable Gain Step Size Mute attenuation Minimum Programmable Gain Maximum Programmable Gain Programmable Gain Step Size Mute attenuation Guaranteed monotonic LOUT ROUT SPKPGA, LOPGA ROPGA Output Programmable Gain Amplifiers (PGAs) OUT3, OUT4, Minimum Programmable Gain Maximum Programmable Gain Programmable Gain Step Size Mute attenuation OUT3 OUT4 (also applies RON) Speaker Attenuation (SPKATTN) Minimum Programmable Gain Maximum Programmable Gain Programmable Gain Step Size Mute attenuation AINLMODE AINRMODE AINLMODE AINRMODE AINLMODE AINRMODE AINLMODE AINRMODE AINLMODE AINRMODE AINLMODE AINRMODE Outputs INMIXL INMIXR Outputs INMIXL INMIXR Outputs INMIXL INMIXR Line Inputs Record path INMIXL INMIXR Line Inputs Record path INMIXL INMIXR Line Inputs Record path INMIXL INMIXR TEST CONDITIONS -16.5
Production Data
UNIT
Input Programmable Gain Amplifiers (PGAs) LIN12, LIN34, RIN12 RIN34
Output Differential Single Ended Converters DIFFINL DIFFINR
Input Mixers INMIXL INMIXR
Output Programmable Gain Amplifiers (PGAs) SPKPGA, LOPGA, ROPGA, LOUT ROUT
March 2009,
Production Data
WM8990
Test Conditions DCVDD 1.8V, DBVDD 3.3V, AVDD HPVDD 3.3V, SPKVDD 1kHz signal, 48kHz, gain 0dB, 24-bit audio data unless otherwise stated. PARAMETER Input Path Performance (A-weighted) (-1dBFS input) THD+N (-1dBFS input) Crosstalk (L/R) AVDD PSRR (217Hz) DCVDD PSRR (217Hz) (A-weighted) (-1dBFS input) THD+N (-1dBFS input) (A-weighted) (-1dBFS input) THD+N (-1dBFS input) Crosstalk (L/R) (A-weighted) (-1dBFS input) THD+N (-1dBFS input) (A-weighted) (-1dBFS input) THD+N (-1dBFS input) Crosstalk (L/R) AVDD PSRR (217Hz) (A-weighted) (-1dBFS input) THD+N (-1dBFS input) (A-weighted) (-1dBFS input) THD+N (-1dBFS input) Crosstalk (L/R) (A-weighted) (-1dBFS input) THD+N (-1dBFS input) (A-weighted) (-1dBFS input) THD+N (-1dBFS input) (A-weighted) (-1dBFS input) THD+N (-1dBFS input) Input PGAs INMIXL INMIXR, AVDD 2.7V Input PGAs DIFFINL DIFFINR, AVDD 3.3V Input PGAs DIFFINL DIFFINR, AVDD 2.7V RXP-RXN RXVOICE, AVDD 3.3V RXP-RXN RXVOICE, AVDD 2.7V Line inputs INMIXL INMIXR, AVDD 2.7V Record path (DACs ADCs INMIXL INMIXR), AVDD 3.3V Record path (DACs ADCs INMIXL INMIXR), AVDD 2.7V Input PGAs INMIXL INMIXR, AVDD 3.3V Line inputs INMIXL INMIXR, AVDD 3.3V -100 -100 -100 TEST CONDITIONS UNIT
March 2009,
WM8990
Test Conditions DCVDD 1.8V, DBVDD 3.3V, AVDD HPVDD 3.3V, SPKVDD +25oC, 1kHz signal, 48kHz, gain 0dB, 24-bit audio data unless otherwise stated. PARAMETER (A-weighted) THD+N Crosstalk (L/R) AVDD PSRR (217Hz) (A-weighted) THD+N (A-weighted) THD+N Crosstalk (L/R) AVDD PSRR (217Hz) Offset Load (A-weighted) THD+N Minimum Line Resistance Maximum Line Capacitance (A-weighted) (PO=20mW) THD+N (PO=20mW) (PO=5mW) THD+N (PO=5mW) Crosstalk (L/R) AVDD PSRR (217Hz) HPVDD PSRR (217Hz) (A-weighted) (PO=5mW) THD+N (PO=5mW) (A-weighted) (PO=20mW) THD+N (PO=20mW) (PO=5mW) THD+N (PO=5mW) Crosstalk (L/R) AVDD PSRR (217Hz) HPVDD PSRR (217Hz) (A-weighted) (PO=20mW) THD+N (PO=20mW) (PO=5mW) THD+N (PO=5mW) LOUT, ROUT, RL=16, AVDD=HPVDD= 2.7V
DACL DACR
Production Data
TEST CONDITIONS singleended line out, 0dBFS input, AVDD 3.3V
-100
UNIT
Output Path (Line Outputs 50pF Load, Headphone Outputs Load, Speaker Output Load)
singleended line out, 0dBFS input, AVDD 2.7V differential line out, 0dBFS input, AVDD 3.3V
-100
differential line out, 0dBFS input, AVDD 2.7V LOP, LON, ROP, LOP, LON, ROP, LOUT ROUT, RL=32, AVDD=HPVDD= 3.3V
AC-Coupled Headphone Outputs -100
LOUT ROUT, RL=32, AVDD=HPVDD= 2.7V LOUT ROUT, RL=16, AVDD=HPVDD= 3.3V
AC-Coupled Headphone Outputs
LOUT ROUT
-100
LOMIX ROMIX
RLOAD 16Ohm
March 2009,
Production Data Test Conditions DCVDD 1.8V, DBVDD 3.3V, AVDD HPVDD 3.3V, SPKVDD +25oC, 1kHz signal, 48kHz, gain 0dB, 24-bit audio data unless otherwise stated. PARAMETER (A-weighted) (PO=20mW) THD+N (PO=20mW) (PO=5mW) THD+N (PO=5mW) Crosstalk (L/R) AVDD PSRR (217Hz) HPVDD PSRR (217Hz) Offset Load (A-weighted) (PO=20mW) THD+N (PO=20mW) (PO=5mW) THD+N (PO=5mW) (A-weighted) (PO=20mW) THD+N (PO=20mW) (PO=5mW) THD+N (PO=5mW) Crosstalk (L/R) AVDD PSRR (217Hz) HPVDD PSRR (217Hz) (A-weighted) (PO=20mW) THD+N (PO=20mW) (PO=5mW) THD+N (PO=5mW) Minimum Headphone Resistance SPKVDD Leakage Current (A-weighted) (PO=0.5W) THD+N (PO=0.5W) (PO=1.0W) THD+N (PO=1.0W) SPKVDD PSRR(217Hz) (A-weighted) (PO=0.5W) THD+N (PO=0.5W) (PO=1.0W) THD+N (PO=1.0W) SPKVDD PSRR(217Hz) Offset Load LOUT, ROUT Capless (OUT3 pseudo GND), RL=16, AVDD=HPVDD= 2.7V LOUT, ROUT, OUT3, OUT4 SPKVDD=5.0V, Speaker Output (Direct) AVDD=3.3V, SPKVDD=5V, class controlled using volume, ACGAIN=DCGA IN=1.52 Speaker Output (Direct) AVDD=3.3V, SPKVDD=5V, class controlled using volume LOUT/OUT3 ROUT/OUT4, RL=16, AVDD=HPVDD= 2.7V LOUT ROUT Capless (OUT3 pseudo GND), RL=16, AVDD=HPVDD= 3.3V LOUT/OUT3 ROUT/OUT4, RL=16, AVDD=HPVDD= 3.3V TEST CONDITIONS Fully Differential Headphone Outputs -100 Capless Headphone Outputs
WM8990
UNIT
March 2009,
WM8990
Test Conditions DCVDD 1.8V, DBVDD 3.3V, AVDD HPVDD 3.3V, SPKVDD +25oC, 1kHz signal, 48kHz, gain 0dB, 24-bit audio data unless otherwise stated. PARAMETER (A-weighted) (PO=20mW) THD+N (PO=20mW) (PO=5mW) THD+N (PO=5mW) AVDD PSRR (217Hz) HPVDD PSRR (217Hz) Offset Load (A-weighted) (PO=20mW) THD+N (PO=20mW) (PO=5mW) THD+N (PO=5mW) (A-weighted) (PO=20mW) THD+N (PO=20mW) (PO=5mW) THD+N (PO=5mW) AVDD PSRR (217Hz) HPVDD PSRR (217Hz) (A-weighted) (PO=20mW) THD+N (PO=20mW) (PO=5mW) THD+N (PO=5mW) (A-weighted) (PO=0.5W) THD+N (PO=0.5W) (PO=1.0W) THD+N (PO=1.0W) AVDD PSRR (217Hz) SPKVDD PSRR(217Hz) (A-weighted) (PO=0.5W) THD+N (PO=0.5W) (PO=1.0W) THD+N (PO=1.0W) AVDD PSRR (217Hz) SPKVDD PSRR(217Hz) Offset Load Line Input SPKMIX, AVDD=3.3V, SPKVDD=5V, Class Mode RXVOICE LOMIX ROMIX Headphone Outputs, AVDD=HPVDD= 2.7V Line Input SPKMIX, AVDD=3.3V, SPKVDD=5V, ACGAIN= DCGAIN=1.52, Class Mode Differential Input RXP/RXN Differential Output OUT3/OUT4, AVDD=HPVDD= 2.7V RXVOICE LOMIX ROMIX Headphone Outputs, AVDD=HPVDD= 3.3V Differential Input RXP/RXN Differential Output OUT3/OUT4, AVDD=HPVDD= 3.3V TEST CONDITIONS
Production Data
UNIT
Bypass Path Performance (Line Outputs 50pF load, Headphone Outputs load, Speaker Output load)
March 2009,
Production Data Test Conditions DCVDD 1.8V, DBVDD 3.3V, AVDD HPVDD 3.3V, SPKVDD +25oC, 1kHz signal, 48kHz, gain 0dB, 24-bit audio data unless otherwise stated. PARAMETER (A-weighted) (0dB output) THD+N (0dB output) AVDD PSRR (217Hz) Offset Load (A-weighted) (0dB output) THD+N (0dB output) (A-weighted) (PO=20mW) THD+N (PO=20mW) (PO=5mW) THD+N (PO=5mW) AVDD PSRR (217Hz) HPVDD PSRR (217Hz) Crosstalk (L/R) (A-weighted) (PO=20mW) THD+N (PO=20mW) (PO=5mW) THD+N (PO=5mW) (A-weighted) (PO=20mW) THD+N (PO=20mW) (PO=5mW) THD+N (PO=5mW) AVDD PSRR (217Hz) HPVDD PSRR (217Hz) Crosstalk (L/R) (A-weighted) (PO=20mW) THD+N (PO=20mW) (PO=5mW) THD+N (PO=5mW) Line Input Headphones LOMIX ROMIX, RL=16, AVDD=HPVDD= 2.7V Input LOMIX ROMIX LOUT ROUT, RL=16, AVDD=HPVDD= 2.7V Line Input Headphones LOMIX ROMIX, RL=16, AVDD=HPVDD= 3.3V Input Differential Line Out, AVDD=2.7V Input LOMIX ROMIX LOUT ROUT, RL=16, AVDD=HPVDD= 3.3V Input Differential Line Out, AVDD=3.3V TEST CONDITIONS
WM8990
UNIT
March 2009,
WM8990
Test Conditions DCVDD 1.8V, DBVDD 3.3V, AVDD HPVDD 3.3V, SPKVDD +25oC, 1kHz signal, 48kHz, gain 0dB, 24-bit audio data unless otherwise stated. PARAMETER Multi-Path Channel Separation Headset Voice Call: DAC/Headset Voice Separation 1kHz 0dBFS playback LOUT ROUT; Quiescent input LIN12 RIN12 (Gain=+12dB), differential output LOP/LON ROP/RON; Measure crosstalk LOP/LON ROP/RON output Headset Voice Call: DAC/Speaker Voice Separation 1kHz 0dBFS playback speaker, output; Quiescent input LIN12 RIN12 (Gain=+12dB), differential output LOP/LON ROP/RON; Measure crosstalk LOP/LON ROP/RON output Voice Call: Voice Voice Separation fs=8kHz DAC, DAC_SB_FILT=1; -5dBFS differential mono output from DACs OUT3/OUT4; Quiescent input input (Gain=+12dB) INMIXL INMIXR; Measure crosstalk output Speakerphone Voice Call: DAC/Speaker Separation fs=8kHz DAC, DAC_SB_FILT=1; 0dBFS output speaker output); record from input (Gain=+30dB); Measure crosstalk output Speaker Voice Call: Voice Voice Separation 1kHz Full scale differential input RXP/RXN, output OUT3/OUT4; Quiescent input LIN12 RIN12 (Gain=+12dB), differential output LOP/LON ROP/RON; Measure crosstalk LOP/LON ROP/RON output
Production Data
TEST CONDITIONS
UNIT
March 2009,
Production Data Test Conditions DCVDD 1.8V, DBVDD 3.3V, AVDD HPVDD 3.3V, SPKVDD +25oC, 1kHz signal, 48kHz, gain 0dB, 24-bit audio data unless otherwise stated. PARAMETER Headset Voice Call: Voice Voice Separation
LIN1 RIN1
WM8990
TEST CONDITIONS
UNIT
LIN12 RIN12 +12dB (Single-ended differential mode)
1kHz full scale differential input RXP/RXN RXVOICE LOMIX ROMIX, output LOUT ROUT; Quiescent input LIN12 RIN12 (Gain=+12dB), differential output LOP/LON ROP/RON; Measure crosstalk LOP/LON ROP/RON output Stereo Line Record Playback: DAC/Headset Separation -5dBFS input DACs, playback LOUT ROUT1; record from line input; Measure crosstalk output
LIN2 RIN2
LOPMIX ROPMIX
LOAD
Quiescent input
LOMIX
LOUT
Full scale input
RXVOICE
ROMIX
ROUT
LIN2, LIN4, RIN2 RIN4
INMIXL INMIXR
ADCL ADCR
Quiescent input -5dBFS, 1kHz CROSSTALK
DACL
LOMIX LOUTVOL
LOUT
-5dBFS, 1kHz
DACR
ROMIX ROUTVOL
ROUT
March 2009,
WM8990
Test Conditions DCVDD 1.8V, DBVDD 3.3V, AVDD HPVDD 3.3V, SPKVDD +25oC, 1kHz signal, 48kHz, gain 0dB, 24-bit audio data unless otherwise stated. PARAMETER Analogue Reference Levels VMID Midrail Reference Voltage Bias Voltage load current M1BSEL=0 M2BSEL=0 load current M1BSEL=1 M2BSEL=1 Bias Current Source Output Noise Density AVDD PSRR (217Hz) 1kHz 20kHz 100mV pk-pk @217Hz AVDD AVDD/2 TEST CONDITIONS
Production Data
UNIT nV/Hz
Microphone Bias
Digital Input Output Input HIGH Level Input Level
Note that digital input pins should left unconnected floating. Internal pull-up/pull-down resistors enabled GPIO1, GPIO3, GPIO4 GPIO5 required. GPIO Clock output duty cycle (Integer OPCLKDIV) SYSCLK=MCLK; OPCLKDIV=0000 SYSCLK=MCLK; OPCLKDIV=1000 SYSCLK=PLL output; OPCLKDIV=0000 SYSCLK=PLL output; OPCLKDIV=1000 Clock output duty cycle (Non-integer OPCLKDIV) SYSCLK=MCLK; OPCLKDIV=0100 SYSCLK=PLL output; OPCLKDIV=0100 Interrupt response time accessory button detect Input de-bounced Input de-bounced TOCLKSEL=1 Input de-bounced
Output HIGH Level Output Level Input capacitance Input leakage Input Frequency Lock time
IOL=1mA IOH=-1mA
-0.9 fSYSCLK fSYSCLK fSYSCLK fSYSCLK
PRESCALE PRESCALE
14.4
March 2009,
Production Data
WM8990
TERMINOLOGY
Signal-to-Noise Ratio (dB) measure difference level between maximum theoretical full scale output signal output with input signal applied. Total Harmonic Distortion (dB) level value harmonic distortion products relative amplitude measured output signal. Total Harmonic Distortion plus Noise (dB) THD+N level value harmonic distortion products plus noise specified bandwidth relative amplitude measured output signal. Crosstalk (L/R) (dB) left-to-right right-to-left channel crosstalk measured signal level idle channel test signal frequency relative signal level output active channel. active channel configured supplied with appropriate input signal drive full scale output, with signal measured output associated idle channel. example, measured signal level output idle right channel (RIN2 ADCR) with full scale signal level output active left channel (LIN1 ADCL). Multi-Path Channel Separation (dB) measured signal level idle path test signal frequency relative signal level output active path. active path configured supplied with appropriate input signal drive full scale output, with signal measured output specified idle path. performance measurements carried with 20kHz pass filter, where noted A-weighted filter. Failure such filter will result higher lower readings than found Electrical Characteristics. pass filter removes band noise; although audible affect dynamic specification values. Mute Attenuation This measure difference level between full scale output signal output with mute applied.
March 2009,
WM8990 TYPICAL POWER CONSUMPTION
Control Register Mode (default state power-up) VSEL Other settings AVDD HPVDD SPKVDD DBVDD DCVDD IAVDD (mA) 0.028 0.029 0.030 0.031 0.008 0.008 0.009 0.009 0.087 0.096 0.106 0.117 5.272 5.603 5.927 6.261 5.125 5.434 5.738 6.053 2.950 3.315 3.684 4.055 2.951 3.315 3.683 4.055 2.950 3.315 3.684 4.056 2.950 3.315 3.683 4.055 2.952 3.316 3.683 4.055 2.951 3.317 3.684 4.055 2.951 3.315 3.684 4.056 2.950 3.315 3.683 4.055 2.950 3.315 3.683 4.055 2.955 3.319 3.686 4.057 3.934 4.184 4.672 5.166 3.621 4.080 4.548 5.021 3.087 3.470 3.856 4.246 0.442 0.499 0.556 0.613 2.307 2.374 2.660 2.953 5.043 5.512 5.981 6.457 IHPVDD ISPKVDD IDBVDD (mA) 0.000 0.000 0.000 0.000 0.000 0.000 0.000 0.000 0.000 0.000 0.000 0.000 0.000 0.000 0.000 0.000 0.000 0.000 0.000 0.000 0.705 0.558 0.640 0.726 1.430 1.367 1.544 1.742 0.828 0.743 0.835 0.937 2.563 2.476 2.508 2.556 15.767 15.789 15.675 15.836 0.699 0.550 0.629 0.711 1.019 0.915 1.045 1.180 0.748 0.624 0.704 0.789 1.950 1.868 1.905 1.950 11.421 11.362 11.349 11.406 0.000 0.000 0.000 0.000 0.000 0.000 0.000 0.000 0.000 0.000 0.000 0.000 0.697 0.544 0.621 0.702 0.796 0.615 0.703 0.794 0.382 0.299 0.343 0.389 (mA) 0.000 0.000 0.000 0.000 0.000 0.000 0.000 0.000 0.000 0.000 0.000 0.000 0.000 0.000 0.000 0.000 0.000 0.000 0.000 0.000 0.000 0.000 0.000 0.000 0.000 0.000 0.000 0.000 0.000 0.000 0.000 0.000 0.000 0.000 0.000 0.000 0.000 0.000 0.000 0.000 0.000 0.000 0.000 0.000 0.000 0.000 0.000 0.000 0.000 0.000 0.000 0.000 0.000 0.000 0.000 0.000 0.000 0.000 0.000 0.000 0.000 0.000 0.000 0.000 3.070 3.652 5.154 7.223 2.823 3.307 4.061 5.057 0.000 0.000 0.000 0.000 0.000 0.000 0.000 0.000 0.000 0.000 0.000 0.000 (mA) 0.000 0.000 0.000 0.000 0.000 0.000 0.000 0.000 0.004 0.008 0.014 0.017 0.023 0.039 0.060 0.063 0.017 0.027 0.061 0.062 0.003 0.007 0.013 0.016 0.004 0.007 0.013 0.016 0.004 0.007 0.013 0.016 0.004 0.007 0.014 0.016 0.004 0.007 0.013 0.016 0.004 0.007 0.013 0.016 0.004 0.007 0.014 0.016 0.004 0.007 0.013 0.016 0.004 0.007 0.014 0.016 0.004 0.007 0.014 0.016 0.004 0.007 0.013 0.016 0.004 0.007 0.013 0.016 0.004 0.007 0.013 0.016 0.000 0.000 0.000 0.000 0.000 0.000 0.000 0.000 0.011 0.017 0.027 0.032
Production Data
IDCVDD Total Power (mA) 0.000 0.000 0.000 0.000 0.000 0.000 0.000 0.000 0.459 0.694 1.025 1.162 2.285 3.317 4.728 5.295 0.758 1.123 1.634 1.841 2.147 3.180 4.544 5.092 2.298 3.380 4.817 5.404 2.263 3.362 4.762 5.344 2.251 3.323 4.736 5.304 2.256 3.343 4.762 5.329 2.147 3.179 4.543 5.089 2.302 3.359 4.806 5.367 2.265 3.337 4.786 5.359 2.253 3.327 4.741 5.312 2.267 3.351 4.777 5.342 2.144 3.179 4.541 5.089 2.138 3.167 4.530 5.073 2.125 3.146 4.496 5.042 0.000 0.000 0.000 0.000 0.000 0.000 0.000 0.000 2.290 3.384 4.820 5.386 (mW) 0.074 0.086 0.099 0.114 0.019 0.024 0.028 0.035 1.067 2.043 3.779 4.667 18.388 25.198 35.357 41.830 15.232 19.176 24.527 28.642 13.739 19.586 29.307 35.600 15.971 22.513 33.189 40.381 14.279 20.596 30.671 37.270 18.943 25.698 36.103 42.951 54.608 65.690 79.640 90.850 13.725 19.565 29.268 35.536 14.868 21.105 31.509 38.228 14.067 20.177 30.314 36.789 17.291 23.883 34.129 40.799 42.901 52.438 65.423 74.956 14.487 20.517 30.446 36.976 23.763 33.322 51.648 72.511 21.482 30.198 44.662 58.780 3.074 3.128 3.884 4.735 8.377 8.966 11.097 13.490 18.789 25.935 36.862 44.150
(thermal sensor disabled) SLEEP (VMID enabled, thermal sensor anabled) Stereo Line Record (L/RIN2 INMIXL/R bypassing PGA) Stereo Line Record (L/RIN2 INMIXL/R bypassing PGA) Playback Coupled Headphones (DAC L/ROUT) 16ohm load Playback Coupled Headphones (DAC L/ROUT) -20dBV Pink Noise into 16ohm load Playback Coupled Headphones (DAC L/ROUT) -30dBV Pink Noise into 16ohm load Playback Coupled Headphones (DAC L/ROUT) 0.1mW/channel into 16ohm load Playback Coupled Headphones (DAC L/ROUT) 5mW/channel into 16ohm load Playback Coupled Headphones (DAC L/ROUT) 32ohm load Playback Coupled Headphones (DAC L/ROUT) -20dBV Pink Noise into 32ohm load Playback Coupled Headphones (DAC L/ROUT) -30dBV Pink Noise into 32ohm load Playback Coupled Headphones (DAC L/ROUT) 0.1mW/channel into 32ohm load Playback Coupled Headphones (DAC L/ROUT) 5mW/channel into 32ohm load Playback Line-Out (DAC ROP/RON) Playback Speaker Class (DAC SPK) 8ohm load Playback Speaker Class (DAC SPK) 8ohm load Radio Coupled Headphones (L/RIN3 L/ROUT bypass LROMIX) 16ohm load Analogue Voice Call Handset Speaker (MIC LIN12 LOP/LON) (RXP/RXN OUT3/4 RXVIOCE AINLMUX) Voice Call (MIC LIN12 LADC) (-12dB sidetone LDAC) (LDAC OUT3, OUT4=MUTE)
Clocks
Clocks
With Clocks
fs=44.1kHz
fs=8kHz
fs=44.1kHz
fs=44.1kHz
fs=44.1kHz
fs=44.1kHz
fs=44.1kHz
fs=44.1kHz
fs=44.1kHz
fs=44.1kHz
fs=44.1kHz
fs=44.1kHz
fs=44.1kHz
fs=44.1kHz
fs=44.1kHz
Notes: Power load included. figures quoted figures quoted quiescent current unless otherwise stated.
March 2009,
Production Data
WM8990
SPEAKER DRIVER PERFORMANCE
Typical speaker driver THD+N performance shown below both Class Class modes. Curves shown four typical SPKVDD supply voltage gain combinations. Load 10H, Frequency 1kHz, +1dB gain active path.
Speaker Class into
Speaker Class (8+10H)
THD+N Ratio Output Power
Speaker Class into
Speaker Class (8+10H)
THD+N Ratio Output Power
THD+N Ratio
THD+N Ratio
0.01
0.01
SPKVDD=5.0V, SPKVDD=4.2V, SPKVDD=3.6V, SPKVDD=3.3V,
AC=DC=1.52x AC=DC=1.27x AC=DC=1.00x AC=DC=1.00x
SPKVDD=5.0V, SPKVDD=4.2V, SPKVDD=3.6V, SPKVDD=3.3V,
AC=DC=1.52x AC=DC=1.27x AC=DC=1.00x AC=DC=1.00x
0.001 0.25 0.75 1.25
0.001 0.25 0.75 1.25
Output Power
Output Power
HEADPHONE DRIVER PERFORMANCE
Typical THD+N performance Headphone Drivers shown below coupled LOUT/ROUT). Curves shown four HPVDD/AVDD supply voltages. Load Frequency 1kHz, +1dB gain active path.
Coupled Headphone into
Coupled Headphone (16ohm)
THD+N Ratio Output Power
Coupled Headphone into
Coupled Headphone (32ohm)
THD+N Ratio Output Power
THD+N Ratio
THD+N Ratio
HPVDD=AVDD=3.6V HPVDD=AVDD=3.3V HPVDD=AVDD=3.0V HPVDD=AVDD=2.7V
HPVDD=AVDD=3.6V HPVDD=AVDD=3.3V HPVDD=AVDD=3.0V HPVDD=AVDD=2.7V
0.01
0.01
Output Power (mW)
Output Power (mW)
March 2009,
WM8990 PSRR PERFORMANCE
SPKVDD LIN2 Speaker
PSRR SPKVDD
PSRR (dB) Frequency (kHz) LIN2-SPK (Class SPKVDD LIN2-SPK (Class SPKVDD LIN2 class AB/D
Production Data
AVDD LIN2 Speaker
PSRR AVDD
PSRR (dB) Frequency (kHz) LIN2-SPK (Class SPKVDD) 3.3V AVDD LIN2-SPK (Class SPKVDD) 3.3V AVDD LIN2 class AB/D
SPKVDD Speaker
PSRR SPKVDD
PSRR (dB)
PSRR (dB)
AVDD Speaker
PSRR AVDD
class AB/D
class AB/D
Frequency (kHz) DACL-SPK (Class SPKVDD DACL-SPK (Class SPKVDD
DACL-SPK (Class SPKVDD) 3.3V AVDD DACL-SPK (Class SPKVDD) 3.3V AVDD Frequency (kHz)
HPVDD Headphone
PSRR HPVDD
PSRR (dB) Frequency (kHz) DAC-OMIX-LOUT/ROUT 3.3V HPVDD DAC-OMIX-OPGA-Differential 3.3V HPVDD Headphone
AVDD Headphone
PSRR AVDD
PSRR (dB) Frequency (kHz) DAC-OMIX-LOUT/ROUT 3.3V AVDD DAC-OMIX-OPGA-Differential 3.3V AVDD Headphone
DCVDD Headphone
PSRR DCVDD
PSRR (dB) Frequency (kHz) DAC-OMIX-LOUT/ROUT 3.3V DCVDD DAC-OMIX-LOUT/ROUT 2.0V DCVDD
PSRR (dB)
AVDD MICBIAS
PSRR AVDD MICBIAS
Frequency (kHz) MICBIAS MBSEL MICBIAS MBSEL
Headphone
March 2009,
Production Data DCVDD Line-In
PSRR DCVDD
PSRR (dB) Line-In
WM8990
AVDD Line-In
PSRR AVDD
PSRR (dB)
IN2-INMIX-ADC 3.3V DCVDD IN2-INMIX-ADC 2.0V DCVDD
Line-In
Frequency (kHz)
IN2-INMIX-ADC 3.3V AVDD IN1PGA-INMIX-ADC 3.3V AVDD Frequency (kHz)
HPVDD Bypass
PSRR HPVDD
IN1PGA-OMIX-LOUT/ROUT 3.3V HPVDD Frequency (kHz) Bypass
AVDD Bypass
PSRR AVDD
PSRR (dB) Frequency (kHz) IN1PGA-OMIX-LOUT/ROUT 3.3V AVDD IN1PGA-LINEDIFF 3.3V AVDD Bypass
PSRR (dB)
HPVDD Bypass
PSRR HPVDD
PSRR (dB) Frequency (kHz) IN3-OMIX-LOUT/ROUT 3.3V HPVDD IN3-OMIX-OPGA-OUT3/OUT4 3.3V HPVDD IN3-OMIX-OPGA-Differential 3.3V HPVDD Bypass
AVDD Bypass
PSRR AVDD
PSRR (dB) Frequency (kHz) IN3-OMIX-LOUT/ROUT 3.3V AVDD IN3-OMIX-OPGA-OUT3/OUT4 3.3V AVDD IN3-OMIX-OPGA-Differential 3.3V AVDD Bypass
HPVDD Bypass
PSRR HPVDD
PSRR (dB) Frequency (kHz) RxVOICE-OMIX-LOUT 3.3V HPVDD IN4-OUT3/OUT4 (16Ohm BTL) 3.3V HPVDD PSRR (dB) Bypass
AVDD Bypass
PSRR AVDD
Bypass
RxVOICE-OMIX-LOUT 3.3V AVDD IN4-OUT3/OUT4 (16Ohm BTL) 3.3V AVDD
Frequency (kHz)
Note: figures based 100mVp-p injected supply relevant test frequency.
March 2009,
WM8990 AUDIO SIGNAL PATHS
Production Data
CSB/ADDR SDIN SCLK MODE
MCLK
GPIO5/DACDAT2 GPIO4/DACLRC2 GPIO3/BCLK2
ADCLRC/GPIO1 ADCDAT DACDAT DACLRC BCLK
DGND DCVDD DBVDD HPVDD HPGND SPKVDD SPKGND
AVDD
VMID
AGND
March 2009,
Production Data
WM8990
SIGNAL TIMING REQUIREMENTS
SYSTEM CLOCK TIMING
MCLK
MCLKY MCLKH MCLKL
Figure System Clock Timing Requirements
Test Conditions DCVDD=1.8V, DBVDD=AVDD=3.3V, SPKVDD=5V, DGND=AGND=SPKGND=0V, +25oC PARAMETER System Clock Timing Information MCLK cycle time MCLK duty cycle TMCLKY TMCLKH/TMCLKL 33.33 60:40 40:60 SYMBOL CONDITIONS UNIT
March 2009,
WM8990
AUDIO INTERFACE TIMING MASTER MODE
Production Data
Figure Digital Audio Data Timing Master Mode (see Control Interface)
Test Conditions DCVDD=1.8V, DBVDD=AVDD=3.3V, SPKVDD=5V, DGND=AGND=SPKGND=0V, TA=+25oC, Master Mode, fs=48kHz, MCLK=256fs, 24-bit data, unless otherwise stated. PARAMETER Audio Data Timing Information ADCLRC/ DACLRC DACLRC2) propagation delay from BCLK BCLK2) falling edge ADCDAT propagation delay from BCLK falling edge DACDAT DACDAT2) setup time BCLK rising edge DACDAT DACDAT2) hold time from BCLK rising edge tDDA tDST tDHT SYMBOL UNIT
March 2009,
Production Data
WM8990
AUDIO INTERFACE TIMING SLAVE MODE
Figure Digital Audio Data Timing Slave Mode
Test Conditions DCVDD=1.8V, DBVDD=AVDD=3.3V, SPKVDD=5V, DGND=AGND=SPKGND=0V, TA=+25oC, Slave Mode, fs=48kHz, MCLK=256fs, 24-bit data, unless otherwise stated. PARAMETER Audio Data Input Timing Information BCLK BCLK2) cycle time BCLK BCLK2) pulse width high BCLK BCLK2) pulse width ADCLRC/ DACLRC DACLRC2) set-up time BCLK BCLK2) rising edge ADCLRC/ DACLRC DACLRC2) hold time from BCLK BCLK2) rising edge DACDAT DACDAT2) hold time from BCLK BCLK2) rising edge ADCDAT propagation delay from BCLK falling edge DACDAT DACDAT2) set-up time BCLK BCLK2) rising edge Note: BCLK BCLK2) period should always greater than equal MCLK period. tBCY tBCH tBCL tLRSU tLRH SYMBOL UNIT
March 2009,
WM8990
AUDIO INTERFACE TIMING MODE
Production Data
mode, important that devices attempt drive ADCDAT simultaneously. timing WM8990 ADCDAT tri-stating start data transmission described Figure table below.
Figure Digital Audio Data Timing Mode
Test Conditions AVDD=3.3V, SPKVDD=5V, DGND=AGND=SPKGND=0V, TA=+25oC, Master Mode, fs=48kHz, MCLK=256fs, 24-bit data, unless otherwise stated. PARAMETER Audio Data Timing Information ADCDAT setup time from BCLK falling edge DCVDD DBVDD 3.6V DCVDD DBVDD 1.71V ADCDAT release time from BCLK falling edge DCVDD DBVDD 3.6V DCVDD DBVDD 1.71V CONDITIONS UNIT
March 2009,
Production Data
WM8990
CONTROL INTERFACE TIMING 2-WIRE MODE
2-wire mode selected connecting MODE low.
SDIN SCLK
Figure Control Interface Timing 2-Wire Serial Control Mode
Test Conditions DCVDD=1.8V, DBVDD=AVDD=HPVDD=3.3V, SPKVDD=5V, DGND=AGND=HPGND=SPKGND=0V, TA=+25oC, Slave Mode, fs=48kHz, MCLK 256fs, 24-bit data, unless otherwise stated. PARAMETER Program Register Input Information SCLK Frequency SCLK Pulse-Width SCLK High Pulse-Width Hold Time (Start Condition) Setup Time (Start Condition) Data Setup Time SDIN, SCLK Rise Time SDIN, SCLK Fall Time Setup Time (Stop Condition) Data Hold Time Pulse width spikes that will suppressed SYMBOL UNIT
March 2009,
WM8990
CONTROL INTERFACE TIMING 3-WIRE MODE
3-wire mode selected connecting MODE high.
Production Data
Figure Control Interface Timing 3-Wire Serial Control Mode (Write Cycle)
SCLK
SDOUT
Figure Control Interface Timing 3-Wire Serial Control Mode (Read Cycle)
Test Conditions DCVDD=1.8V, DBVDD=AVDD=HPVDD=3.3V, SPKVDD=5V, DGND=AGND=HPGND=SPKGND=0V, TA=+25oC, Slave Mode, fs=48kHz, MCLK=256fs, 24-bit data, unless otherwise stated. PARAMETER Program Register Input Information falling edge SCLK rising edge SCLK falling edge rising edge SCLK pulse cycle time SCLK pulse width SCLK pulse width high SDIN SCLK set-up time SDIN SCLK hold time Pulse width spikes that will suppressed SCLK falling edge SDOUT transition tCSU tCHO tSCY tSCL tSCH tDSU tDHO SYMBOL UNIT
March 2009,
Production Data
WM8990
CONTROL INTERFACE TIMING 4-WIRE MODE
4-wire mode supports readback SDOUT which available GPIO function.
Figure Control Interface Timing 4-Wire Serial Control Mode (Write Cycle)
SCLK
SDOUT
Figure Control Interface Timing 4-Wire Serial Control Mode (Read Cycle)
Test Conditions DCVDD=1.8V, DBVDD=AVDD=HPVDD=3.3V, SPKVDD=5V, DGND=AGND=HPGND=SPKGND=0V, =+25oC, Slave Mode, fs=48kHz, MCLK=256fs, 24-bit data, unless otherwise stated. PARAMETER Program Register Input Information SCLK rising edge falling edge SCLK falling edge rising edge SCLK pulse cycle time SCLK pulse width SCLK pulse width high SDIN SCLK set-up time SDIN SCLK hold time SDOUT propagation delay from SCLK rising edge Pulse width spikes that will suppressed SCLK falling edge SDOUT transition tCSU tCHO tSCY tSCL tSCH tDSU tDHO SYMBOL UNIT
March 2009,
WM8990 INTERNAL POWER RESET CIRCUIT
Production Data
Figure Internal Power Reset Circuit Schematic
WM8990 includes internal Power-On-Reset Circuit, shown Figure which used reset digital logic into default state after power circuit powered from AVDD monitors DCVDD. asserts PORB AVDD DCVDD below minimum threshold.
Figure Typical Power Sequence where AVDD Powered before DCVDD
Figure shows typical power-up sequence where AVDD comes first. When AVDD goes above minimum threshold, Vpora, there enough voltage circuit guarantee PORB asserted chip held reset. this condition, writes control interface ignored. AVDD full supply level. Next DCVDD rises Vpord_on PORB released high registers their default state writes control interface take place. power down, where AVDD falls first, PORB asserted whenever AVDD drops below minimum threshold Vpora_off.
March 2009,
Production Data
WM8990
Figure Typical Power Sequence where DCVDD Powered before AVDD
Figure shows typical power-up sequence where DCVDD comes first. First assumed that DCVDD already specified operating voltage. When AVDD goes above minimum threshold, Vpora, there enough voltage circuit guarantee PORB asserted chip held reset. this condition, writes control interface ignored. When AVDD rises Vpora_on, PORB released high registers their default state writes control interface take place. power down, where DCVDD falls first, PORB asserted whenever DCVDD drops below minimum threshold Vpord_off. SYMBOL Vpora Vpora_on Vpora_off Vpord_on Vpord_off 1.52 0.92 UNIT
Table Typical Operation (typical values, tested)
Notes: AVDD DCVDD suffer brown-out (i.e. drop below minimum recommended operating level below Vpora_off Vpord_off) then chip will reset will resume normal operation when voltage back recommended level again. chip will enter reset power down when AVDD DCVDD falls below Vpora_off Vpord_off. This important supply turned frequently power management system. minimum tpor period maintained even DCVDD AVDD have zero rise time. This specification guaranteed design rather than test.
March 2009,
WM8990 DEVICE INTRODUCTION
Production Data
WM8990 power, high quality audio codec designed interface with wide range processors analogue components. high level mixed-signal integration very small 3.226x3.44mm footprint makes ideal portable applications such mobile phones. Eight highly flexible analogue inputs allow interfacing four microphone inputs plus multiple stereo mono line inputs (single-ended differential). Connections external voice CODEC, radio, melody line input, handset headset fully supported. Signal routing output mixers within CODEC been designed maximum flexibility support wide variety usage modes. analogue output drivers integrated, including high power, high quality speaker driver, capable providing class mode class mode into BTL. Four headphone drivers provided, supporting speakers stereo headsets. Fully differential headphone drive supported excellent crosstalk performance removing need large expensive headphone capacitors. Four line outputs available voice output voice CODEC, interfacing additional speaker driver single-ended fully differential line output. outputs have integrated click suppression. speaker supply been designed with leakage high PSRR, support direct connection Lithium battery. addition speaker PGA, gain settings allow output signal levels maximised many commonly-used SPKVDD/AVDD combinations. Internal signal routing amplifier configurations have been optimised provide lowest possible power consumption number common usage scenarios such voice calls music playback. stereo ADCs DACs hi-fi quality using 24-bit, low-order oversampling architecture deliver optimum performance. flexible clocking arrangement supports mixed sample rates, while integrated ultra-low power provides additional flexibility. high pass filter available path removing offsets suppressing frequency noise such mechanical vibration wind noise. digital mixing path from provides sidetone enhanced quality during voice calls. soft mute un-mute available pop-free music playback. WM8990 highly flexible digital audio interface, supporting number protocols, including I2S, DSP, MSB-first left/right justified, operate master slave modes. operation supported mode. A-law -law companding also supported. Time division multiplexing (TDM) available allow multiple devices stream data simultaneously same bus, saving space power. Alternative interface pins provided allow connection additional processor. SYSCLK (system clock) provides clocking ADCs, DACs, core, class outputs digital audio interface. SYSCLK derived directly from MCLK integrated PLL, providing flexibility support wide range clocking schemes. MCLK frequencies typically used portable systems supported sample rates between 8kHz 48kHz. flexible switching clock class speaker drivers (synchronous with audio clocks best performance) also derived from SYSCLK. allow full software control over features, WM8990 uses standard 2-wire 3/4-wire control interface with readback registers supported. fully compatible ideal partner wide range industry standard microprocessors, controllers DSPs. Unused circuitry disabled software save power, while leakage currents extend standby time portable battery-powered applications. device address selected using CSB/ADDR pin. Versatile GPIO functionality provided, with support five button/accessory detect inputs with interrupt status readback flexible de-bouncing options, clock output, logic logic control additional external circuitry.
March 2009,
Production Data
WM8990
INPUT SIGNAL PATH
WM8990 eight highly flexible analogue input channels, configurable many combinations following: four pseudo-differential single-ended microphone inputs eight mono line inputs stereo line inputs Mono input from external voice CODEC fully balanced differential inputs These inputs mixed together independently routed different combinations output drivers. internal record path provided input mixers allow output mixed with input signal path (e.g. karaoke voice call recording). WM8990 input signal paths control registers illustrated Figure
Figure Control Registers Input Signal Path
March 2009,
WM8990
MICROPHONE INPUTS
Production Data
four microphones connected WM8990, either single-ended pseudodifferential mode. noise microphone bias fully integrated reduce need external components. single-ended microphone input configuration, microphone signal connected inverting input (LIN1, LIN3, RIN1 RIN3). non-inverting input PGAs should internally connected VMID this configuration. This enabled Input configuration register settings. this configuration, LIN2, LIN4, RIN2 RIN4 free used line inputs bypass inputs. pseudo-differential microphone input configuration, non-inverted microphone signal connected non-inverting input (LIN2, LIN4, RIN2 RIN4) inverted noisy ground) signal connected inverting input (LIN1, LIN3, RIN1 RIN3). input that used either microphone configuration should enabled line input path same time. gain input PGAs controlled register settings. Note that input impedance LIN1, LIN3, RIN1 RIN3 changes with input gain setting, described under "Electrical Characteristics". (Note this does apply input paths which bypass input PGA.) input impedance LIN2, LIN4, RIN2 RIN4 does change with input gain. inverting non-inverting inputs therefore matched differential configuration fully differential.
Figure Single-Ended Microphone Input
Figure Differential Microphone Input
LINE INPUTS
eight analogue input pins configured line inputs. Various signal paths exist provide flexibility, high performance power consumption different usage modes. LIN1 RIN1 operate line inputs Input PGAs LIN12 RIN12 provide high gain required small input signals. LIN2 RIN2 operate line inputs directly input mixers speaker output mixer. Direct routing speaker output minimises power consumption reducing number active amplifiers signal path. LIN3 RIN3 operate line inputs Input PGAs line input directly either output mixers LOMIX ROMIX. LIN1+LIN3 RIN1+RIN3 also used fully balanced differential inputs Input PGAs input mixers. (Note that these inputs have matched input impedances.) LIN4/RXN RIN4/RXP operate line inputs directly outputs OUT3 OUT4, providing ultra-low power stereo mono differential signal path (e.g. from external voice CODEC) speaker. LIN4/RXN RIN4/RXP also operate mono differential input input signal path output mixer stages.
March 2009,
Production Data
WM8990
Figure LIN1 RIN1 Line Inputs
Figure LIN2 RIN2 Line Inputs
Figure LIN3 RIN3 Line Inputs
Figure Fully Balanced Differential Input
Figure LIN4 RIN4 Voice Inputs with Direct Power Path Speaker
March 2009,
WM8990
Production Data
Figure LIN4 RIN4 Line Inputs
INPUT ENABLE
Input PGAs enabled using register bits LIN12_ENA, LIN34_ENA, RIN12_ENA RIN34_ENA described Table REGISTER ADDRESS (02h) LABEL DEFAULT
LIN34_ENA (rw) LIN12_ENA (rw) RIN34_ENA (rw) RIN12_ENA (rw)
LIN34 Input Enable disabled enabled LIN12 Input Enable disabled enabled RIN34 Input Enable disabled enabled RIN12 Input Enable disabled enabled
Table Input Enable
enable input PGAs, reference voltage VMID bias current must also enabled. "Power Management" definitions associated controls VMID_MODE VREF_ENA.
March 2009,
Production Data
WM8990
MICROPHONE BIAS CONTROL
MICBIAS output provides noise reference voltage suitable biasing electret type microphones external resistor. Refer Applications Information section recommended external components. MICBIAS voltage enabled disabled using MICBIAS_ENA control voltage selected using MBSEL register detailed Table REGISTER ADDRESS (01h) LABEL MICBIAS_ENA (rw) MBSEL DEFAULT DESCRIPTION Microphone Bias (high impedance output) Microphone Bias Voltage Control AVDD 0.65 AVDD
(3Ah)
Table Microphone Bias Control
Note that maximum source current capability MICBIAS 3mA. external biasing resistance must large enough limit MICBIAS current 3mA.
MICROPHONE CURRENT DETECT
MICBIAS current detect function allows detection accessories such headset microphones. When MICBIAS load current exceeds programmable thresholds, (e.g. short circuit current normal operating current), interrupt GPIO output generated. current detection circuit enabled bit; current thresholds selected MCDTHR MCDSCTH register fields described Table "General Purpose Input/Output" full description these fields.
March 2009,
WM8990
INPUT CONFIGURATION
Production Data
Each four Input PGAs configured single-ended pseudo-differential mode. Single-ended microphone operation Input selected connecting input source inverting input. non-inverting input must connected VMID setting appropriate register bits. pseudo-differential microphone operation, inverting non-inverting inputs both connected input source VMID. line input other connection using Input PGA, appropriate input should disconnected from external connected VMID. Register bits LMN1, LMP2, LMN3, LMP4, RMN1, RMP2, RMN3 RMP4 control connection inputs device pins shown Table maximum available attenuation these input paths achieved using these bits disable input path applicable PGA. When enabled analogue inputs General Purpose inputs, input pins biased VREF resistor setting BUFIOEN bit. "Pop Suppression Control" details. REGISTER ADDRESS (28h) LABEL LMP4 DEFAULT DESCRIPTION LIN34 Non-Inverting Input Select LIN4 connected LIN4 connected LIN34 Inverting Input Select LIN3 connected LIN3 connected LIN12 Non-Inverting Input Select LIN2 connected LIN2 connected LIN12 Inverting Input Select LIN1 connected LIN1 connected RIN34 Non-Inverting Input Select RIN4 connected RIN4 connected RIN34 Inverting Input Select RIN3 connected RIN3 connected RIN12 Non-Inverting Input Select RIN2 connected RIN2 connected RIN12 Inverting Input Select RIN1 connected RIN1 connected
LMN3
LMP2
LMN1
RMP4
RMN3
RMP2
RMN1
Table Input Configuration
March 2009,
Production Data
WM8990
INPUT VOLUME CONTROL
Each four Input PGAs independently controlled gain range -16.5dB +30dB 1.5dB steps. gains inverting non-inverting inputs PGAs always equal. Each Input independently muted using mute bits described Table with specified mute attenuation achieved simultaneously disconnecting corresponding inputs described Table prevent "zipper noise", zero-cross function provided, that when enabled, volume updates will take place until zero-crossing detected. event long period without zerocrossings, timeout function available. When this function enabled (using TOCLK_ENA register bit), volume will update after timeout period earlier zero-cross occurred. timeout period TOCLK_RATE. "Clocking Sample Rates" more information these fields. IPVU controls loading input volume data. When IPVU volume data will loaded into respective control register, will actually change gain setting. LIN12, RIN12, LIN34, RIN34 volume settings updated when written IPVU. This makes possible update gain input paths simultaneously. Input Volume Control register fields described Table Table REGISTER ADDRESS (18h) LABEL IPVU[0] DEFAULT DESCRIPTION Input Volume Update Writing this will cause input volumes updated simultaneously (LIN12, LIN34, RIN12 RIN34) LIN12 Mute Disable Mute Enable Mute LIN12 Zero Cross Detector Change gain immediately Change gain zero cross only LIN12 Volume (See Table volume range) Input Volume Update Writing this will cause input volumes updated simultaneously (LIN12, LIN34, RIN12 RIN34) LIN34 Mute Disable Mute Enable Mute LIN34 Zero Cross Detector Change gain immediately Change gain zero cross only LIN34 Volume (See Table volume range) Input Volume Update Writing this will cause input volumes updated simultaneously (LIN12, LIN34, RIN12 RIN34) RIN12 Mute Disable Mute Enable Mute RIN12 Zero Cross Detector Change gain immediately Change gain zero cross only
LI12MUTE
LI12ZC
(19h)
LIN12VOL [4:0] IPVU[1]
01011b (0dB)
LI34MUTE
LI34ZC
(1Ah)
LIN34VOL [4:0] IPVU[2]
01011b (0dB)
RI12MUTE
RI12ZC
March 2009,
WM8990
(1Bh) RIN12VOL [4:0] IPVU[3] 01011b (0dB)
Production Data RIN12 Volume (See Table volume range) Input Volume Update Writing this will cause input volumes updated simultaneously (LIN12, LIN34, RIN12 RIN34) RIN34 Mute Disable Mute Enable Mute RIN34 Zero Cross Detector Change gain immediately Change gain zero cross only RIN34 Volume (See Table volume range)
RI34MUTE
RI34ZC
RIN34VOL [4:0]
01011b (0dB)
Table Input Volume Control
March 2009,
Production Data
WM8990
LIN12VOL[4:0], LIN34VOL[4:0], RIN12VOL[4:0], RIN34VOL[4:0] 00000 00001 00010 00011 00100 00101 00110 00111 01000 01001 01010 01011 01100 01101 01110 01111 10000 10001 10010 10011 10100 10101 10110 10111 11000 11001 11010 11011 11100 11101 11110 11111 Table Input Volume Range VOLUME (DB) -16.5 -15.0 -13.5 -12.0 -10.5 -9.0 -7.5 -6.0 -4.5 -3.0 -1.5 +1.5 +3.0 +4.5 +6.0 +7.5 +9.0 +10.5 +12.0 +13.5 +15.0 +16.5 +18.0 +19.5 +21.0 +22.5 +24.0 +25.5 +27.0 +28.5 +30.0
March 2009,
WM8990
INPUT MIXER ENABLE
Production Data
WM8990 analogue input mixers which allow Input PGAs Line Inputs combined number ways output ADCs Output Mixers bypass paths. input mixers INMIXL INMIXR enabled AINL_ENA AINR_ENA register bits, described Table These control bits also enable Input Multiplexers Differential Input drivers, described following section. REGISTER ADDRESS (02h) LABEL AINL_ENA (rw) DEFAULT DESCRIPTION Left Input Path Enable (Enables AINLMUX, INMIXL, DIFFINL RXVOICE input AINLMUX) Input Path disabled Input Path enabled Right Input Path Enable (Enables AINRMUX, INMIXR, DIFFINR RXVOICE input AINRMUX) Input Path disabled Input Path enabled
AINR_ENA (rw)
Table Input Mixer Enable
INPUT MIXER CONFIGURATION
left right channel input multiplexers AINLMUX AINRMUX select three input sources Left Right channels independently. three input sources follows: INMIXL INMIXR output combination Input PGAs, line inputs internal record path). RXVOICE differential single-ended conversion inputs). DIFFINL DIFFINR output differential single-ended conversion Input PGAs). input source multiplexers controlled register bits AINLMODE AINRMODE described Table REGISTER ADDRESS (27h) LABEL AINLMODE [1:0] DEFAULT DESCRIPTION AINLMUX Input Source INMIXL (Left Input Mixer) RXVOICE (RXP RXN) DIFFINL (LIN12 LIN34 PGA) (Reserved) AINRMUX Input Source INMIXR (Right Input Mixer) RXVOICE (RXP RXN) DIFFINR (RIN12 RIN34 PGA) (Reserved)
AINRMODE [1:0]
Table Input Mixer Configuration
Input Mixer configuration described each three modes following sections. Note that Left Right multiplexer (mode) settings independently.
March 2009,
Production Data
WM8990
Mixer Mode (AINLMODE=00, AINRMODE=00), adjustable gain control available input mixers INMIXL INMIXR available input signals (PGA outputs, line inputs record paths). This configuration illustrated Figure applicable register settings shown Table CONFIGURATION Left Channel Mixer Mode (INMIXL AINLMUX) Select Mixer Mode Enable input paths required (see Table Table full definitions applicable settings listed here) Right Channel Mixer Mode (INMIXR AINRMUX) Select Mixer Mode Enable input paths required (see Table Table full definitions applicable settings listed here) REGISTER SETTINGS AINLMODE L12MNB, L12MNBST LIN12VOL, LIN12MUTE L34MNB, L34MNBST LIN34VOL, LIN34MUTE LDBVOL LI2BVOL AINRMODE R12MNB, R12MNBST RIN12VOL, RIN12MUTE R34MNB, R34MNBST RIN34VOL, RIN34MUTE RDBVOL RI2BVOL
Table Mixer Mode Register Settings
Figure Mixer Mode Signal Paths
March 2009,
WM8990
Production Data Voice Mode (AINLMODE=01, AINRMODE=01), adjustable gain control available RXVOICE output LR4BVOL[2:0] LL4BVOL[2:0] register fields left channel RL4BVOL[2:0] RR4BVOL[2:0] right channel. Both Volume fields desired channel(s) must same value true Differential input characteristics. This configuration illustrated Figure applicable register settings shown Table CONFIGURATION Left Channel Voice Mode (RXVOICE AINLMUX) REGISTER SETTINGS Select Voice Mode Enable Voice input required Important: These register fields must same value. Table full definitions these fields. Select Voice Mode Enable Voice input required Important: These register fields must same value. Table full definitions these fields. AINLMODE LL4BVOL LR4BVOL
Right Channel Voice Mode (RXVOICE AINRMUX)
AINRMODE RL4BVOL RR4BVOL
Table RxVoice Mode Register Settings
Figure RxVoice Mode Signal Paths
March 2009,
Production Data
WM8990
Differential Mode (AINLMODE=10, AINRMODE=10), additional volume control available input signal path, Input volume control used adjust signal level with other modes. Both PGAs desired channel(s) must enabled, volumes each same value true Differential input characteristics. Output (LIN12 RIN12) Mixer (INMIXL INMIXR) path must also enabled desired channel(s) register L12MNB R12MNB. This configuration illustrated Figure applicable register settings shown Table CONFIGURATION Left Channel Differential Mode (DIFFINL AINLMUX) REGISTER SETTINGS Select Differential Mode Enable LIN12 input path channel volume required. Important: LIN12 LIN34 volume mute settings must same value. Table full definitions these fields. Select Differential Mode Enable RIN12 input path channel volume required. Important: RIN12 RIN34 volume mute settings must same value. Table full definitions these fields. AINLMODE L12MNB LIN12VOL, LIN12MUTE LIN34VOL, LIN34MUTE
Right Channel Differential Mode (DIFFINR AINRMUX)
AINRMODE R12MNB RIN12VOL, RIN12MUTE RIN34VOL, RIN34MUTE
Table Differential Mode Register Settings
Figure Differential Mode Signal Paths
March 2009,
WM8990
INPUT MIXER VOLUME CONTROL
Production Data
Input Mixer volume controls described Table Left Channel Table Right Channel. Input levels Mute, 30dB boost. other gain controls provide adjustment from -12dB +6dB steps. prevent noise recommended that gain mute controls input mixers modified while signal paths active. volume control required input signal path recommended that input volume controls volume controls used instead input mixer gain registers. REGISTER ADDRESS (29h) LABEL L34MNB DEFAULT DESCRIPTION LIN34 Output INMIXL Mute Mute Un-Mute LIN34 Output INMIXL Gain +30dB LIN12 Output INMIXL Mute Mute Un-Mute LIN12 Output INMIXL Gain +30dB LOMIX INMIXL Gain Mute Mute -12dB -9dB -6dB -3dB +3dB +6dB LIN2 INMIXL Gain Mute Mute -12dB -9dB -6dB -3dB +3dB +6dB RXVOICE AINLMUX Gain Mute Mute -12dB -9dB -6dB -3dB +3dB +6dB
L34MNBST
L12MNB
L12MNBST
LDBVOL [2:0]
000b (Mute)
(2Bh)
LI2BVOL [2:0]
000b (Mute)
LR4BVOL [2:0]
000b (Mute)
March 2009,
Production Data REGISTER ADDRESS LABEL LL4BVOL [2:0] DEFAULT 000b (Mute)
WM8990
RXVOICE INMIXL Gain Mute Mute -12dB -9dB -6dB -3dB +3dB +6dB Note LR4BVOL must same value LL4BVOL when AINLMODE=01.
Table Left Input Mixer Volume Control
REGISTER ADDRESS (2A)
LABEL R34MNB
DEFAULT
DESCRIPTION RIN34 Output INMIXR Mute Mute Un-Mute RIN34 Output INMIXR Gain +30dB RIN12 Output INMIXR Mute Mute Un-Mute RIN12 Output INMIXR Gain +30dB ROMIX INMIXR Gain Mute Mute -12dB -9dB -6dB -3dB +3dB +6dB RIN2 INMIXR Gain Mute Mute -12dB -9dB -6dB -3dB +3dB +6dB RXVOICE AINRMUX Gain Mute Mute -12dB -9dB -6dB -3dB +3dB +6dB March 2009,
R34MNBST
R12MNB
R12MNBST
RDBVOL [2:0]
000b (Mute)
(2Ch)
RI2BVOL [2:0]
000b (Mute)
RL4BVOL [2:0]
000b (Mute)
WM8990
REGISTER ADDRESS LABEL RR4BVOL [2:0] DEFAULT 000b (Mute)
Production Data DESCRIPTION RXVOICE INMIXR Gain Mute Mute -12dB -9dB -6dB -3dB +3dB +6dB Note RL4BVOL must same value RR4BVOL when AINRMODE=01.
Table Right Input Mixer Volume Control
ANALOGUE DIGITAL CONVERTER (ADC)
WM8990 uses stereo 24-bit, oversampled sigma-delta ADCs. multi-bit feedback high oversampling rates reduces effects jitter high frequency noise. full scale input level proportional AVDD. "Electrical Characteristics" further details. input signal greater than full scale overload cause distortion. ADCs enabled ADCL_ENA ADCR_ENA register bits. both ADCs enabled, they should enabled simultaneously, i.e. with same register write. there requirement enable ADCs independently another them simultaneously, ADCL_ADCR_LINK should set. EXT_ACCESS_ENA must before writing ADCL_ADCR_LINK bit. REGISTER ADDRESS (02h) LABEL ADCL_ENA (rw) ADCR_ENA (rw) EXT_ACCESS_ENA DEFAULT DESCRIPTION Left Enable disabled enabled Right Enable disabled enabled Extended Register Access disabled enabled Sync disabled Sync enabled
R117 (75h)
R122 (7Ah)
ADCL_ADCR_LINK
Table Enable Control
March 2009,
Production Data
WM8990
DIGITAL VOLUME CONTROL
output ADCs digitally amplified attenuated over range from -71.625dB +17.625dB 0.375dB steps. volume each channel controlled separately. gain given eight-bit code given 0.375 (X-192) 239; MUTE +17.625dB
ADC_VU controls loading digital volume control data. When ADC_VU ADCL_VOL ADCR_VOL control data will loaded into respective control register, will actually change digital gain setting. Both left right gain settings updated when written ADC_VU. This makes possible update gain both channels simultaneously. REGISTER ADDRESS (0Fh) LABEL ADC_VU DEFAULT DESCRIPTION Volume Update Writing this will cause left right volume updated simultaneously Left Digital Volume (See Table volume range) Volume Update Writing this will cause left right volume updated simultaneously Right Digital Volume (See Table volume range)
(10h)
ADCL_VOL [7:0] ADC_VU
1100_0000b (0dB)
ADCR_VOL [7:0]
1100_0000b (0dB)
Table Digital Volume Control
March 2009,
WM8990
MUTE -71.625 -71.250 -70.875 -70.500 -70.125 -69.750 -69.375 -69.000 -68.625 -68.250 -67.875 -67.500 -67.125 -66.750 -66.375 -66.000 -65.625 -65.250 -64.875 -64.500 -64.125 -63.750 -63.375 -63.000 -62.625 -62.250 -61.875 -61.500 -61.125 -60.750 -60.375 -60.000 -59.625 -59.250 -58.875 -58.500 -58.125 -57.750 -57.375 -57.000 -56.625 -56.250 -55.875 -55.500 -55.125 -54.750 -54.375 -54.000 -53.625 -53.250 -52.875 -52.500 -52.125 -51.750 -51.375 -51.000 -50.625 -50.250 -49.875 -49.500 -49.125 -48.750 -48.375 -48.000 -47.625 -47.250 -46.875 -46.500 -46.125 -45.750 -45.375 -45.000 -44.625 -44.250 -43.875 -43.500 -43.125 -42.750 -42.375 -42.000 -41.625 -41.250 -40.875 -40.500 -40.125 -39.750 -39.375 -39.000 -38.625 -38.250 -37.875 -37.500 -37.125 -36.750 -36.375 -36.000 -35.625 -35.250 -34.875 -34.500 -34.125 -33.750 -33.375 -33.000 -32.625 -32.250 -31.875 -31.500 -31.125 -30.750 -30.375 -30.000 -29.625 -29.250 -28.875 -28.500 -28.125 -27.750 -27.375 -27.000 -26.625 -26.250 -25.875 -25.500 -25.125 -24.750 -24.375 -24.000 -23.625 -23.250 -22.875 -22.500 -22.125 -21.750 -21.375 -21.000 -20.625 -20.250 -19.875 -19.500 -19.125 -18.750 -18.375 -18.000 -17.625 -17.250 -16.875 -16.500 -16.125 -15.750 -15.375 -15.000 -14.625 -14.250 -13.875 -13.500 -13.125 -12.750 -12.375 -12.000 -11.625 -11.250 -10.875 -10.500 -10.125 -9.750 -9.375 -9.000 -8.625 -8.250 -7.875 -7.500 -7.125 -6.750 -6.375 -6.000 -5.625 -5.250 -4.875 -4.500 -4.125 -3.750 -3.375 -3.000 -2.625 -2.250 -1.875 -1.500 -1.125 -0.750 -0.375
Production Data
ADCL_VOL ADCL_VOL ADCL_VOL ADCL_VOL ADCR_VOL Volume (dB) ADCR_VOL Volume (dB) ADCR_VOL Volume (dB) ADCR_VOL Volume (dB)
0.000 0.375 0.750 1.125 1.500 1.875 2.250 2.625 3.000 3.375 3.750 4.125 4.500 4.875 5.250 5.625 6.000 6.375 6.750 7.125 7.500 7.875 8.250 8.625 9.000 9.375 9.750 10.125 10.500 10.875 11.250 11.625 12.000 12.375 12.750 13.125 13.500 13.875 14.250 14.625 15.000 15.375 15.750 16.125 16.500 16.875 17.250 17.625 17.625 17.625 17.625 17.625 17.625 17.625 17.625 17.625 17.625 17.625 17.625 17.625 17.625 17.625 17.625 17.625
Table Digital Volume Range
March 2009,
Production Data
WM8990
HIGH PASS FILTER
digital high pass filter applied default path remove offsets. This filter also programmed remove frequency noise voice applications (e.g. wind noise mechanical vibration). This filter controlled using ADC_HPF_ENA ADC_HPF_CUT register bits. hi-fi mode high pass filter optimised removing offsets without degrading bass response cut-off frequency 3.7Hz fs=44.1kHz. voice mode high pass filter optimised voice communication recommended program cut-off frequency below 300Hz (e.g. ADC_HPF_CUT=11 fs=8kHz ADC_HPF_CUT=10 fs=16kHz). REGISTER ADDRESS (0Eh) LABEL ADC_HPF_ENA DEFAULT DESCRIPTION Digital High Pass Filter Enable disabled enabled Digital High Pass Filter Cut-Off Frequency (fc) Hi-fi mode (fc=4Hz fs=48kHz) Voice mode (fc=127Hz fs=16kHz) Voice mode (fc=130Hz fs=8kHz) Voice mode (fc=267Hz fs=8kHz) (Note: scales with sample rate. Table cut-off frequencies supported sample rates)
ADC_HPF_CUT [1:0]
Table High Pass Filter Control Registers
Sample Frequency (kHz) 8.000 11.025 16.000 22.050 24.000 32.000 44.100 48.000
Cut-off frequency (Hz) ADC_HPF_CUT ADC_HPF_CUT ADC_HPF_CUT ADC_HPF_CUT 1063 1464 1594
Table High Pass Filter Cut-Off Frequencies
high pass filter characteristics shown "Digital Filter Characteristics" section.
March 2009,
WM8990
DIGITAL MIXING
Production Data
data combined various ways support range different usage modes. Data from either ADCs routed either left right channel digital audio interface. addition, data from either digital audio interface channels routed either left right DAC. "Digital Audio Interface" more information audio interface.
DIGITAL MIXING PATHS
Figure shows digital mixing paths available WM8990 digital core.
MAIN REGISTER REFERENCE REGISTER ALSO REFERENCED ELSEWHERE DIAGRAM READBACK AVAILABLE
DIGITAL CORE
DACL
HIGH PASS FILTER (VOICE HI-FI)
ADCL_DAC_SVOL [7:0]
ADC_TO_DACL [1:0] 00=0 01=ADCL 10=ADCR 11=Reserved ADC_TO_DACR [1:0]
DACL_VOL [7:0] MONO
ADCL_VOL [7:0]
ADCL_ENA ADC_HPF_CUT [1:0] ADCR_ENA
ADC_HPF_ENA
DAC_MONO
HIGH PASS FILTER (VOICE HI-FI)
DACR_VOL [7:0] DAC_MUTE, DAC_MUTEMODE, DAC_MUTERATE, DAC_SB_FILT, DEEMP[1:0]
DACR
ADCR_VOL [7:0]
ADCR_DAC_SVOL [7:0]
DAC_BOOST [1:0]
DAC_BOOST +6dB +12dB +18dB
ADCR_DATINV ADCL_DATINV
DACL_DATINV DACR_DATINV DACL_SRC DACR_SRC
AIFADCR_SRC AIFADCL_SRC
DIGITAL AUDIO INTERFACE
A-law u-law support Support
GPIO
Alternative Interface Button Control Accessory Detect Clock Output
Figure Digital Mixing Paths
March 2009,
Production Data
WM8990
polarity each output signal changed under software control using ADCL_DATINV ADCR_DATINV register bits. AIFADCL_SRC AIFADCR_SRC register bits used select which used left right digital audio interface data. These register bits described Table REGISTER ADDRESS (04h) LABEL AIFADCL_SRC DEFAULT DESCRIPTION Left Digital Audio channel source Left data output left channel Right data output left channel Right Digital Audio channel source Left data output right channel Right data output right channel Left Invert Left output inverted Left output inverted Right Invert Right output inverted Right output inverted
AIFADCR_SRC
(0Eh)
ADCL_DATINV
ADCR_DATINV
Table Routing Control
input data source each changed under software control using register bits DACL_SRC DACR_SRC. polarity each input also modified using register bits DACL_DATINV DACR_DATINV. These register bits described Table REGISTER ADDRESS (05h) LABEL DACL_SRC DEFAULT DESCRIPTION Left Data Source Select Left outputs left channel data Left outputs right channel data Right Data Source Select Right outputs left channel data Right outputs right channel data Left Invert Left output inverted Left output inverted Right Invert Right output inverted Right output inverted
DACR_SRC
(0Ah)
DACL_DATINV
DACR_DATINV
Table Routing Control
March 2009,
WM8990
INTERFACE VOLUME BOOST
Production Data
digital gain function available audio interface boost volume when small signal received DACDAT. This controlled using register bits DAC_BOOST[1:0]. prevent clipping input, this function should used when boosted data expected greater than 0dBFS. REGISTER ADDRESS (05h) 11:10 LABEL DAC_BOOST [1:0] DEFAULT DESCRIPTION Input Volume Boost +6dB (Input data must exceed -6dBFS) +12dB (Input data must exceed -12dBFS) +18dB (Input data must exceed -18dBFS)
Table Interface Volume Boost
DIGITAL SIDETONE
digital sidetone available when ADCs DACs operating same sample rate. Digital data from either left right mixed with audio interface data left right channels. Sidetone data taken from high pass filter output, reduce frequency noise sidetone (e.g. wind noise mechanical vibration). digital sidetone will function when ADCs DACs operating different sample rates. When using digital sidetone, recommended that ADCs enabled before un-muting DACs prevent noise. volumes sidetone volumes should appropriate level avoid clipping input. digital sidetone controlled shown Table REGISTER ADDRESS (0Dh) 12:9 LABEL ADCL_DAC_SVOL [3:0] ADCR_DAC_SVOL [3:0] ADC_TO_DACL [1:0] DEFAULT 0000b 0000b DESCRIPTION Left Digital Sidetone Volume (See Table volume range) Right Digital Sidetone Volume (See Table volume range) Left Digital Sidetone Source sidetone Left Right Reserved Right Digital Sidetone Source sidetone Left Right Reserved
ADC_TO_DACR [1:0]
Table Digital Sidetone Control
March 2009,
Production Data
WM8990
ADCL_DAC_SVOL ADCR_DAC_SVOL 0000 0001 0010 0011 0100 0101 0110 0111 1000 1001 1010 1011 1100 1101 1110 1111 SIDETONE VOLUME
Table Digital Sidetone Volume
March 2009,
WM8990
DIGITAL ANALOGUE CONVERTER (DAC)
Production Data
WM8990 DACs receive digital input data from DACDAT digital sidetone path. digital audio data converted oversampled streams on-chip, true 24-bit digital interpolation filters. bitstream data enters multi-bit, sigma-delta DACs, which convert them high quality analogue audio signals. multi-bit architecture reduces high frequency noise sensitivity clock jitter. also uses Dynamic Element Matching technique high linearity distortion. analogue outputs from DACs then mixed with other analogue inputs using output mixers LOMIX, ROMIX speaker output mixer SPKMIX. DACs enabled DACL_ENA DACR_ENA register bits. REGISTER ADDRESS (03h) LABEL DACL_ENA (rw) DACR_ENA (rw) DEFAULT DESCRIPTION Left Enable disabled enabled Right Enable disabled enabled
Table Enable Control
DIGITAL VOLUME CONTROL
output level each controlled digitally over range from -71.625dB 0.375dB steps. level attenuation eight-bit code given 0.375 (X-192) 192; MUTE
DAC_VU controls loading digital volume control data. When DAC_VU DACL_VOL DACR_VOL control data will loaded into respective control register, will actually change digital gain setting. Both left right gain settings updated when written DAC_VU. This makes possible update gain both channels simultaneously. REGISTER ADDRESS (0Bh) LABEL DAC_VU DEFAULT DESCRIPTION Volume Update Writing this will cause left right volume updated simultaneously Left Digital Volume (See Table volume range) Volume Update Writing this will cause left right volume updated simultaneously Right Digital Volume (See Table volume range)
(0Ch)
DACL_VOL [7:0] DAC_VU
1100_0000b (0dB)
DACR_VOL [7:0]
1100_0000b (0dB)
Table Digital Volume Control
March 2009,
Production Data
WM8990
MUTE -71.625 -71.250 -70.875 -70.500 -70.125 -69.750 -69.375 -69.000 -68.625 -68.250 -67.875 -67.500 -67.125 -66.750 -66.375 -66.000 -65.625 -65.250 -64.875 -64.500 -64.125 -63.750 -63.375 -63.000 -62.625 -62.250 -61.875 -61.500 -61.125 -60.750 -60.375 -60.000 -59.625 -59.250 -58.875 -58.500 -58.125 -57.750 -57.375 -57.000 -56.625 -56.250 -55.875 -55.500 -55.125 -54.750 -54.375 -54.000 -53.625 -53.250 -52.875 -52.500 -52.125 -51.750 -51.375 -51.000 -50.625 -50.250 -49.875 -49.500 -49.125 -48.750 -48.375 -48.000 -47.625 -47.250 -46.875 -46.500 -46.125 -45.750 -45.375 -45.000 -44.625 -44.250 -43.875 -43.500 -43.125 -42.750 -42.375 -42.000 -41.625 -41.250 -40.875 -40.500 -40.125 -39.750 -39.375 -39.000 -38.625 -38.250 -37.875 -37.500 -37.125 -36.750 -36.375 -36.000 -35.625 -35.250 -34.875 -34.500 -34.125 -33.750 -33.375 -33.000 -32.625 -32.250 -31.875 -31.500 -31.125 -30.750 -30.375 -30.000 -29.625 -29.250 -28.875 -28.500 -28.125 -27.750 -27.375 -27.000 -26.625 -26.250 -25.875 -25.500 -25.125 -24.750 -24.375 -24.000 -23.625 -23.250 -22.875 -22.500 -22.125 -21.750 -21.375 -21.000 -20.625 -20.250 -19.875 -19.500 -19.125 -18.750 -18.375 -18.000 -17.625 -17.250 -16.875 -16.500 -16.125 -15.750 -15.375 -15.000 -14.625 -14.250 -13.875 -13.500 -13.125 -12.750 -12.375 -12.000 -11.625 -11.250 -10.875 -10.500 -10.125 -9.750 -9.375 -9.000 -8.625 -8.250 -7.875 -7.500 -7.125 -6.750 -6.375 -6.000 -5.625 -5.250 -4.875 -4.500 -4.125 -3.750 -3.375 -3.000 -2.625 -2.250 -1.875 -1.500 -1.125 -0.750 -0.375 0.000 0.000 0.000 0.000 0.000 0.000 0.000 0.000 0.000 0.000 0.000 0.000 0.000 0.000 0.000 0.000 0.000 0.000 0.000 0.000 0.000 0.000 0.000 0.000 0.000 0.000 0.000 0.000 0.000 0.000 0.000 0.000 0.000 0.000 0.000 0.000 0.000 0.000 0.000 0.000 0.000 0.000 0.000 0.000 0.000 0.000 0.000 0.000 0.000 0.000 0.000 0.000 0.000 0.000 0.000 0.000 0.000 0.000 0.000 0.000 0.000 0.000 0.000 0.000
DACL_VOL DACL_VOL DACL_VOL DACL_VOL DACR_VOL Volume (dB) DACR_VOL Volume (dB) DACR_VOL Volume (dB) DACR_VOL Volume (dB)
Table Digital Volume Range
March 2009,
WM8990
SOFT MUTE SOFT UN-MUTE
Production Data
WM8990 soft mute function which, when enabled, gradually attenuates volume output. When soft mute disabled, gain will either gradually ramp back digital gain setting, return instantly digital gain setting, depending DAC_MUTEMODE register bit. soft-muted default (DAC_MUTE play back audio signal, this function must first disabled setting DAC_MUTE Soft Mute Mode would typically enabled (DAC_MUTEMODE when using DAC_MUTE during playback audio data that when DAC_MUTE subsequently disabled, sudden volume increase will create noise jumping immediately previous volume level (e.g. resuming playback after pausing during track). Soft Mute Mode would typically disabled (DAC_MUTEMODE when un-muting start music file, order that first part track attenuated (e.g. when starting playback track, resuming playback after pausing between tracks).
muting un-muting using volume control bits DACL_VOL DACR_VOL.
muting un-muting using soft mute DAC_MUTE. Soft Mute Mode enabled (DAC_MUTEMODE
muting un-muting using soft mute DAC_MUTE. Soft Mute Mode enabled (DAC_MUTEMODE
Figure Mute Control volume ramp rate during soft mute un-mute controlled DAC_MUTERATE bit. Ramp rates fs/32 fs/2 selectable shown Table ramp rate determines rate which volume will increased decreased. actual ramp time depends extent difference between muted un-muted volume settings. REGISTER ADDRESS (0Ah) LABEL DAC_MUTERATE DEFAULT DESCRIPTION Soft Mute Ramp Rate Fast ramp (fs/2, maximum ramp time 10.7ms fs=48k) Slow ramp (fs/32, maximum ramp time 171ms fs=48k) Soft Mute Mode Disabling soft-mute (DAC_MUTE=0) will cause volume change immediately DACL_VOL DACR_VOL settings Disabling soft-mute (DAC_MUTE=0) will cause volume ramp gradually DACL_VOL DACR_VOL settings Soft Mute Control Un-mute Mute
DAC_MUTEMODE
DAC_MUTE
Table Soft-Mute Control
March 2009,
Production Data
WM8990
MONO
digital mono-mix mode enabled using DAC_MONO register bit. This mono will output enabled DACs. prevent clipping, -6dB attenuation automatically applied mono mix. REGISTER ADDRESS (0Ah) LABEL DAC_MONO DEFAULT DESCRIPTION Mono Stereo Mono (Mono output enabled DACs)
Table Mono
DE-EMPHASIS
Digital de-emphasis applied playback data (e.g. when data comes from with pre-emphasis used recording). De-emphasis filtering available sample rates 48kHz, 44.1kHz 32kHz. "Digital Filter Characteristics" section details de-emphasis filter characteristics. REGISTER ADDRESS (0Ah) Control LABEL DEEMP [1:0] DEFAULT DESCRIPTION De-Emphasis Control de-emphasis 32kHz sample rate 44.1kHz sample rate 48kHz sample rate
Table De-Emphasis Control
SLOPING STOPBAND FILTER
filter types available, selected register DAC_SB_FILT. When operating lower sample rates (e.g. during voice communication) recommended that sloping stopband filter type selected (DAC_SB_FILT=1) reduce out-of-band noise which audible sample rates. "Digital Filter Characteristics" section details filter characteristics. REGISTER ADDRESS (0Ah) LABEL DAC_SB_FILT DEFAULT DESCRIPTION Selects filter characteristics Normal mode Sloping stopband mode
Table Sloping Stopband Filter
March 2009,
WM8990
OUTPUT SIGNAL PATH
Production Data
WM8990 output routing mixers provide high degree flexibility, allowing operation many simultaneous signal paths through device various analogue outputs. outputs provide many combinations headphone, loudspeaker single-ended line drivers. "Analogue Outputs" further details these outputs. WM8990 output signal paths control registers illustrated Figure
Figure Control Registers Output Signal Path
March 2009,
Production Data
WM8990
OUTPUT SIGNAL PATHS ENABLE
output mixers drivers independently enabled disabled described Table Note that headphone outputs LOUT ROUT have dedicated volume controls. result, output PGAs LOPGA ROPGA need enabled provide volume control LOUT ROUT outputs. REGISTER ADDRESS (03h) LABEL LON_ENA (rw) LOP_ENA (rw) RON_ENA (rw) ROP_ENA (rw) SPKPGA_ENA (rw) DEFAULT DESCRIPTION Line LONMIX Enable disabled enabled Line LOPMIX Enable disabled enabled Line RONMIX Enable disabled enabled Line ROPMIX Enable disabled enabled SPKMIX Mixer Speaker Enable disabled enabled Note that SPKMIX SPKPGA also enabled when SPK_ENA set. LOPGA Left Volume Control Enable disabled enabled ROPGA Right Volume Control Enable disabled enabled LOMIX Left Output Mixer Enable disabled enabled ROMIX Right Output Mixer Enable disabled enabled SPKMIX Mixer, Speaker Speaker Output Enable disabled enabled OUT3 OUT3MIX Enable disabled enabled OUT4 OUT4MIX Enable disabled enabled LOUT (Left Headphone Output) Enable disabled enabled ROUT (Right Headphone Output) Enable disabled enabled
LOPGA_ENA (rw) ROPGA_ENA (rw) LOMIX_ENA (rw) ROMIX_ENA (rw) SPK_ENA (rw)
(01h)
OUT3_ENA (rw) OUT4_ENA (rw) LOUT_ENA (rw) ROUT_ENA (rw)
Table Output Signal Paths Enable
March 2009,
WM8990
OUTPUT MIXER CONTROL
Production Data
Output Mixer volume controls described Table Left Channel Table Right Channel. gain each analogue input paths controlled independently range described Table input levels controlled digital volume control "Digital Analogue Converter (DAC)" further details this control. REGISTER ADDRESS (2Dh) LABEL LRI3LO DEFAULT DESCRIPTION RIN3 LOMIX Mute Mute Un-mute LIN3 LOMIX Mute Mute Un-mute RIN3 LOMIX Volume (See Table Volume Range) LIN3 LOMIX Volume (See Table Volume Range) LIN12 Output LOMIX Mute Mute Un-mute LIN12 Output LOMIX Volume (See Table Volume Range) RIN12 Output LOMIX Mute Mute Un-mute RIN12 Output LOMIX Volume (See Table Volume Range) AINRMUX Output (Right bypass) LOMIX Mute Mute Un-mute AINRMUX Output (Right bypass) LOMIX Volume (See Table Volume Range) AINLMUX Output (Left bypass) LOMIX Mute Mute Un-mute AINLMUX Output (Left bypass) LOMIX Volume (See Table Volume Range) Left LOMIX Mute Mute Un-mute Note: LDLO must muted when LDSPK=1
(2Dh)
LLI3LO
(31h) (2Fh) (2Dh)
LRI3LOVOL [2:0] LLI3LOVOL [2:0] LL12LO
000b 000b
(2Fh) (2Dh)
LL12LOVOL [2:0] LR12LO
000b
(2Fh) (2Dh)
LR12LOVOL [2:0] LRBLO
000b
(31h)
LRBLOVOL [2:0] LLBLO
000b
(2Dh)
(31h)
LLBLOVOL [2:0] LDLO
000b
(2Dh)
Table Left Output Mixer (LOMIX) Volume Control
March 2009,
Production Data
WM8990
REGISTER ADDRESS (2Eh) LABEL RLI3RO DEFAULT DESCRIPTION LIN3 ROMIX Mute Mute Un-mute RIN3 ROMIX Mute Mute Un-mute LIN3 ROMIX Volume (See Table Volume Range) RIN3 ROMIX Volume (See Table Volume Range) LIN12 Output ROMIX Mute Mute Un-mute LIN12 Output ROMIX Volume (See Table Volume Range) RIN12 Output ROMIX Mute Mute Un-mute RIN12 Output ROMIX Volume (See Table Volume Range) AINLMUX Output (Left bypass) ROMIX Mute Mute Un-mute AINLMUX Output (Left bypass) ROMIX Volume (See Table Volume Range) AINRMUX Output (Right bypass) ROMIX Mute Un-mute AINRMUX Output (Right bypass) ROMIX Volume (See Table Volume Range) Right ROMIX Mute Mute Un-mute Note: RDRO must muted when RDSPK=1
(2Eh)
RRI3RO
(32h) (30h) (2Eh)
RLI3ROVOL [2:0] RRI3ROVOL [2:0] RL12RO
000b 000b
(30h) (2Eh)
RL12ROVOL [2:0] RR12RO
000b
(30h) (2Eh)
RR12ROVOL [2:0] RLBRO
000b
(32h)
RLBROVOL [2:0] RRBRO
000b
(2Eh)
(32h)
RRBROVOL [2:0] RDRO
000b
(2Eh)
Table Right Output Mixer (ROMIX) Volume Control
March 2009,
WM8990
VOLUME SETTING VOLUME (DB)
Production Data
Table LOMIX ROMIX Volume Range
OUTPUT SIGNAL PATH VOLUME CONTROL
output drivers LOPGA, ROPGA, LOUT ROUT independently controlled shown Table Table minimise noise recommended that only LOPGAVOL, ROPGAVOL, LOUTVOL ROUTVOL modified while output signal path active. Other gain controls provided output signal path provide appropriate relative scaling signals from different sources, prevent clipping when multiple signals mixed. prevent noise, only gain controls noted above should modified while playback active. prevent "zipper noise", zero-cross function provided these output paths, that when enabled, volume updates will take place until zero-crossing detected. event long period without zero-crossings, timeout function available. When this function enabled (using TOCLK_ENA register bit), volume will update after timeout period earlier zero-cross occurred. timeout period TOCLK_RATE. "Clocking Sample Rates" more information these fields. OPVU controls loading output driver volume data. When OPVU volume control data will loaded into respective control register, will actually change gain setting. LOPGA, ROPGA, LOUT ROUT volume settings updated when written OPVU. This makes possible update gain output paths simultaneously. Note that headphone outputs LOUT ROUT have dedicated volume controls. result, output PGAs LOPGA ROPGA need enabled provide volume control LOUT ROUT outputs. REGISTER ADDRESS (20h) LABEL OPVU[2] DEFAULT DESCRIPTION Output Volume Update Writing this will update LOPGA, ROPGA, LOUTVOL ROUTVOL volumes simultaneously. LOPGA Zero Cross Enable Zero cross disabled Zero cross enabled LOPGA Volume (See Table output volume control range) Output Volume Update Writing this will update LOPGA, ROPGA, LOUTVOL ROUTVOL volumes simultaneously. ROPGA Zero Cross Enable Zero cross disabled Zero cross enabled
LOPGAZC
LOPGAVOL [6:0] OPVU[3]
(0dB)
(21h)
ROPGAZC
March 2009,
Production Data REGISTER ADDRESS LABEL ROPGAVOL [6:0] OPVU[0] DEFAULT (0dB)
WM8990
DESCRIPTION ROPGA Volume (See Table output volume control range) Output Volume Update Writing this will update LOPGA, ROPGA, LOUTVOL ROUTVOL volumes simultaneously. LOUT (Left Headphone Output) Zero Cross Enable Zero cross disabled Zero cross enabled LOUT (Left Headphone Output) Volume (See Table output volume control range) Output Volume Update Writing this will update LOPGA, ROPGA, LOUTVOL ROUTVOL volumes simultaneously. ROUT (Right Headphone Output) Zero Cross Enable Zero cross disabled Zero cross enabled ROUT (Right Headphone Output) Volume (See Table output volume control range)
(1Ch)
LOZC
LOUTVOL [6:0]
(mute)
(1Dh)
OPVU[1]
ROZC
ROUTVOL [6:0]
(mute)
Table LOPGA, ROPGA, LOUT ROUT Volume Control
March 2009,
WM8990
LOPGAVOL, ROPGAVOL, LOUTVOL, ROUTVOL SPKVOL LOPGAVOL, ROPGAVOL, LOUTVOL, ROUTVOL SPKVOL
Production Data
Volume (dB) MUTE MUTE MUTE MUTE MUTE MUTE MUTE MUTE MUTE MUTE MUTE MUTE MUTE MUTE MUTE MUTE MUTE MUTE MUTE MUTE MUTE MUTE MUTE MUTE MUTE MUTE MUTE MUTE MUTE MUTE MUTE MUTE MUTE MUTE MUTE MUTE MUTE MUTE MUTE MUTE MUTE MUTE MUTE MUTE MUTE MUTE MUTE MUTE
Volume (dB)
Table LOPGA, ROPGA, LOUT, ROUT SPKVOL Volume Range
March 2009,
Production Data
WM8990
speaker mixer SPKMIX, speaker SPKPGA outputs SPKN SPKP controlled described Table Care should taken avoid clipping when enabling more than path speaker mixer. Register bits SPKATTN control speaker output attenuation used avoid clipping when more than full scale signal input mixer. Fine adjustment speaker output made using SPKVOL register field. prevent "zipper noise" when adjusting SPKVOL, zero-cross function provided that, when enabled, volume updates will take place until zero-crossing detected. event long period without zero-crossings, timeout function available. When this function enabled (using TOCLK_ENA register bit), volume will update after timeout period earlier zerocross occurred. timeout period TOCLK_RATE. "Clocking Sample Rates" more information these fields. REGISTER ADDRESS (36h) LABEL LB2SPK DEFAULT DESCRIPTION AINLMUX Output SPKMIX Mute Un-mute AINRMUX Output SPKMIX Mute Un-mute LIN2 SPKMIX Mute Un-mute RIN2 SPKMIX Mute Un-mute LOPGA SPKMIX Mute Un-mute ROPGA SPKMIX Mute Un-mute Left SPKMIX Mute Un-mute Note: LDSPK must muted when LDLO=1 Right SPKMIX Mute Un-mute Note: RDSPK must muted when RDRO=1 Speaker Output Attenuation (SPKN SPKP) -6dB -12dB mute SPKPGA Zero Cross Enable Zero cross disabled Zero cross enabled SPKPGA Volume (see Table SPKPGA volume control range)
RB2SPK
LI2SPK
RI2SPK
LOPGASPK
ROPGASPK
LDSPK
RDSPK
(22h)
SPKATTN [1:0]
(26h)
SPKZC
SPKVOL [6:0]
(0dB)
Table Speaker Output Volume Control
March 2009,
WM8990
Production Data output mixers OUT3MIX OUT4MIX their outputs OUT3 OUT4 controlled described Table Care should taken avoid clipping when enabling more than path OUT3 OUT4. OUT3ATTN OUT4ATTN attenuation controls used prevent clipping when more than full scale signal input mixers. REGISTER ADDRESS (1Fh) LABEL OUT3MUTE DEFAULT DESCRIPTION OUT3 Mute Un-mute Mute OUT3 Attenuation -6dB OUT4 Mute Un-mute Mute OUT4 Attenuation -6dB LIN4/RXN OUT3MIX Mute Un-mute LOPGA OUT3MIX Mute Un-mute RIN4/RXP OUT4MIX Mute Un-mute ROPGA OUT4MIX Mute Un-mute
OUT3ATTN
OUT4MUTE
OUT4ATTN
(33h)
LI4O3
LPGAO3
RI4O4
RPGAO4
Table OUT3 OUT4 Volume Control
March 2009,
Production Data
WM8990
output mixers LOPMIX LONMIX their outputs controlled described Table Care should taken avoid clipping when enabling more than path LON. LOATTN attenuation control used prevent clipping when more than full scale signal input mixer. REGISTER ADDRESS (1Eh) LABEL LONMUTE DEFAULT DESCRIPTION Line Output Mute Un-mute Mute Line Output Mute Un-mute Mute Attenuation -6dB LOPGA LONMIX Mute Un-mute ROPGA LONMIX Mute Un-mute Inverted Output LONMIX Mute Un-mute RIN12 Output LOPMIX Mute Un-mute LIN12 Output LOPMIX Mute Un-mute LOPGA LOPMIX Mute Un-mute
LOPMUTE
LOATTN
(34h)
LLOPGALON
LROPGALON
LOPLON
LR12LOP
LL12LOP
LLOPGALOP
Table Volume Control
March 2009,
WM8990
Production Data output mixers ROPMIX RONMIX their outputs controlled described Table Care should taken avoid clipping when enabling more than path RON. ROATTN attenuation control used prevent clipping when more than full scale signal input mixer. REGISTER ADDRESS (1Eh) LABEL RONMUTE DEFAULT DESCRIPTION Line Output Mute Un-mute Mute Line Output Mute Un-mute Mute Attenuation -6dB ROPGA RONMIX Mute Un-mute LOPGA RONMIX Mute Un-mute Inverted Output RONMIX Mute Un-mute LIN12 Output ROPMIX Mute Un-mute RIN12 Output ROPMIX Mute Un-mute ROPGA ROPMIX Mute Un-mute
ROPMUTE
ROATTN
(35h)
RROPGARON
RLOPGARON
ROPRON
RL12ROP
RR12ROP
RROPGAROP
Table Volume Control
March 2009,
Production Data
WM8990
ANALOGUE OUTPUTS
speaker, headphone line outputs highly configurable used many different ways.
SPEAKER OUTPUT CONFIGURATIONS
speaker outputs SPKP SPKN driven speaker mixer SPKMIX, speaker volume control SPKPGA, which output that combination following signals: Left Right outputs LOMIX ROMIX outputs volume controls LOPGA ROPGA Line inputs LIN2 RIN2 Output from left right input mixers (AINLMUX AINRMUX)
speaker mixer controlled described under "Output Signal Path". speaker mixer output attenuated avoid clipping when mixing multiple signal inputs. Fine adjustment speaker output made speaker volume control SPKPGA. speaker outputs SPKP SPKN operate configuration Class Class amplifier modes. mode selected register CDMODE. outputs capable driving into load 500mW class mode thermal reasons) room temperature. performance higher temperatures, Figure "Recommended Operating Conditions" section. Ultra-low leakage high PSRR allow speaker supply SPKVDD directly connected lithium battery. levels signal boost provided order deliver maximum output power many commonly-used SPKVDD/AVDD combinations. These boost options available both Class Class modes. gain levels from 1.0x 1.8x selected using register bits ACGAIN DCGAIN. prevent noise, DCGAIN ACGAIN should modified while speaker outputs enabled. Note that appropriate SPKVDD supply voltage must provided prevent waveform clipping when speaker boost used. AVDD SPKVDD
DCGAIN[2:0] SPKATTN[1:0] SPEAKER MIXER SPKVOL[6:0] ACGAIN[2:0]
SPKP SPKN
Connection provides additional gain
AGND
DCGAIN[2:0] ACGAIN[2:0] 1.00x 1.27x 1.40x 1.52x 1.67x 1.80x
SPKGND
SPKVDD AVDD VMID DCGAIN VMID AGND Signal ACGAIN VMID DCGAIN
Figure Speaker Boost Operation
March 2009,
WM8990
REGISTER ADDRESS (23h) LABEL CDMODE DEFAULT
Production Data
DESCRIPTION Speaker Class Mode Enable Class mode Class mode Speaker Boost 1.00x boost (+0dB) 1.27x boost (+2.1dB) 1.40x boost (+2.9dB) 1.52x boost (+3.6dB) 1.67x boost (+4.5dB) 1.80x boost (+5.1dB) Reserved Speaker Boost 1.00x boost (+0dB) 1.27x boost (+2.1dB) 1.40x boost (+2.9dB) 1.52x boost (+3.6dB) 1.67x boost (+4.5dB) 1.80x boost (+5.1dB) Reserved
(25h)
DCGAIN [2:0]
000b (1.0x)
ACGAIN [2:0]
000b (1.0x)
Table Speaker Boost Control
HEADPHONE OUTPUT CONFIGURATIONS
headphone outputs LOUT, ROUT, OUT3 OUT4 each driven different output mixers described below. LOUT ROUT pins output LOMIX ROMIX outputs respectively. output mixer OUT3MIX produces output OUT3 that combination LIN4/RXN LOMIX output volume control LOPGA
output mixer OUT4MIX produces output OUT4 that combination RIN4/RXP ROMIX output volume control ROPGA
Full volume control available LOUT ROUT. -6dB attenuation available OUT3 OUT4, with full volume control available using LOPGA ROPGA LOMIX ROMIX signals. outputs LOUT, ROUT, OUT3 OUT4 capable driving 40mW into loads such stereo headsets, headphones, and/or handset speaker. AC-coupled, capless mode fully differential headphone drive modes available. AC-coupled output possible each LOUT, ROUT, OUT3 OUT4 simultaneously. Capless headphone output possible LOUT ROUT using either OUT3 OUT4 common return path. (This achieved muting OUT3 OUT4 required.) mono differential input (e.g. connection external voice CODEC), then OUT3 OUT4 used differential output capable driving handset speaker. signal paths from OUT4 from OUT3 direct, pass through additional amplifiers. This reduces standby active power consumption improves signal quality.
March 2009,
Production Data
WM8990
When driving handset speaker using OUT3 OUT4 other than from RXP/RXN, required phase difference provided inverting outputs alternatively mixing Left Right channels together using either LOMIX ROMIX muting opposite channel. Note that differential output will provide additional gain output pins. Register bits OUT3ATTN OUT4ATTN used compensate this gain required. Fully differential headphone drive possible between LOUT OUT3 between ROUT OUT4. Routing LOPGA OUT3 ROPGA OUT4 results phase inversion LOUT respect OUT3 ROUT with respect OUT4. This allows fully differential headset drive, greatly improved crosstalk performance, improved bass response, increased noise immunity removing need large expensive DC-blocking capacitors. with with
ensure fully balanced differential operation, LOUT OUT3 must same gain each other, ROUT OUT4 must same gain each other. This best achieved setting OUT3ATTN OUT4ATTN 0dB, whilst setting volume controls LOPGAVOL LOUTVOL matching levels setting volume controls ROPGAVOL ROUTVOL matching levels. Some example headphone output configurations shown below.
Figure AC-Coupled Headphone Drive
Figure Capless Mode Headphone Drive
Figure Headphone Speaker Drive
Figure Fully Differential Headphone Drive
March 2009,
WM8990
LINE OUTPUT CONFIGURATIONS
Production Data
line outputs LON, LOP, each driven different output mixers described below. pins output LIN12 input PGA, RIN12 input either LOMIX ROMIX outputs. output ROMIX, LOMIX phase-inverted copy LOP. output LOMIX, ROMIX phase-inverted copy ROP. Volume control LOMIX ROMIX available cases above LOPGA ROPGA. additional -6dB attenuation option provided outputs. outputs LON, LOP, capable driving line loads only. Single ended output possible these output simultaneously. Differential output also possible between between RON. Typical applications line outputs (single-ended differential) are: Handset headset microphone output external voice CODEC Stereo line output Output external speaker driver(s) support stereo loudspeakers
March 2009,
Production Data Some example line output configurations shown below.
WM8990
Figure Stereo Line
Figure Differential Output
Figure Stereo Line
Figure Differential Output Speaker Driver
Figure Stereo Line
Figure Stereo Differential Line
March 2009,
WM8990
DISABLED OUTPUTS
Production Data
Whenever analogue output disabled, connected VREF through resistor; this feature enabled setting BUFIOEN "Pop Suppression Control". This helps prevent noise when output re-enabled. resistance between VREF each output controlled using register VROI. default, high resistance used Headphone outputs (LOUT, ROUT, OUT3 OUT4) Line outputs (LON, LOP, ROP). impedance desired disabled outputs, VROI then decreasing resistance about cases. Note that disabled output used common ground connection capless headphone output described earlier. REGISTER ADDRESS (37h) Additional Control LABEL VROI DEFAULT DESCRIPTION VREF Analogue Output Resistance (Disabled Outputs) (Headphone) (Line Out) from buffered VMID output from buffered VMID output
Table Disabled Outputs VREF Resistance
THERMAL SHUTDOWN
speaker headphone outputs drive very large currents. protect WM8990 from overheating thermal shutdown circuit included. device temperature reaches approximately thermal shutdown circuit enabled (TSHUT_ENA TSHUT_OPDIS speaker headphone amplifiers (LOUT, ROUT, SPKP, SPKN, OUT3 OUT4) will disabled. TSHUT_ENA must enable temperature sensor when using TSHUT_OPDIS thermal shutdown function. output temperature sensor also output GPIO pins. REGISTER ADDRESS (02h) LABEL TSHUT_ENA (rw) TSHUT_OPDIS (rw) DEFAULT DESCRIPTION Thermal Sensor Enable Thermal sensor disabled Thermal sensor enabled Thermal Shutdown Enable (Requires thermal sensor enabled) Thermal shutdown disabled Thermal shutdown enabled
Table Thermal Shutdown
When speaker driver operating class mode internal power dissipation WM8990 likely significantly higher than when operating class mode. Note: prevent potential pops clicks THSUT_ENA TSHUT_OPDIS need configured while speaker headphone outputs off, i.e. LOUT_ENA, ROUT_ENA, OUT3_ENA, OUT4_ENA SPK_ENA (see also Table 79).
March 2009,
Production Data
WM8990
GENERAL PURPOSE INPUT/OUTPUT
WM8990 provides number versatile GPIO functions enable features such mobile support, Wi-Fi voice call recording, button accessory detection clock output. WM8990 multi-purpose pins these functions. GPIO1 GPIO3 GPIO5: Dedicated GPIO pins. LIN3/GPI7 RIN3/GPI8: Analogue inputs button/accessory detect inputs.
following functions available some GPIO pins. Alternative interface (DACDAT, DACLRC, BCLK) Button detect (latched with programmable de-bounce) MICBIAS Accessory current short circuit detect Clock output Temperature sensor output lock output Logic logic output Interrupt event output Serial data output (register readback)
functions available each GPIO pins identified Table GPIO PINS GPIO Function ADCLRC BCLK2 DACLRC2 DACDAT2 Button/Accessory Detect Input Clock Output Temperature Lock Logic Logic Interrupt SDOUT (Readback Data) Pull-up Pull-down Available GPIO1 GPIO3 GPIO4 GPIO5 GPI7 GPI8
Table Functions Available GPIO Pins
GPIO pins configured combination register settings described Table Table following section. order precedence control GPIO pins listed below. pull-up pull-down (GPIOn_PU, GPIOn_PD) Audio Interface GPIO Tristate (AIF_TRIS) configuration (AIFSEL ALRCGPIO1) GPIO functionality (GPIOn_SEL)
March 2009,
WM8990
GPIO CONTROL REGISTERS
Production Data
Table shows dual-function GPIO pins configured operate their different modes. Note that order precedence described earlier applies. Register field AIF_SEL selects function GPIO3, GPIO4 GPIO5 between Audio Interface GPIO functions. Register field ALRCGPIO1 enables GPIO functionality GPIO1. Register AIF_TRIS, when set, takes precedence over AIF_SEL GPIO1 tri-states GPIO pins. REGISTER ADDRESS (08h) LABEL AIF_SEL DEFAULT DESCRIPTION Audio Interface Select Audio interface Audio interface (GPIO3/BCLK2, GPIO4/DACLRC2, GPIO5/DACDAT2) ADCLRC/GPIO1 Function Select ADCLRC GPIO1 (ADCLRC connected DACLRC internally) Audio Interface GPIO Tristate Audio interface GPIO pins operate normally Tristate audio interface GPIO pins
(09h)
ALRCGPIO1
AIF_TRIS
Table GPIO Function Select
GPIO pins also controlled register fields described Table Note order precedence described earlier applies. Pull-up pull-down resistors enabled GPIO1 GPIO3 GPIO5. enabled, these settings take precedence over other GPIO selections that pin. Note that, default, pull-down resistors GPIO3, GPIO4 GPIO5 enabled. When GPIO pins used inputs, de-bounce interrupt masking controlled GPIO pins (including GPI7 GPI8) using GPIOn_DEB_ENA GPIOn_IRQ_ENA bits shown Table each GPIO1 GPIO3 GPIO5, register field GPIOn_SEL used select functions individual GPIO pins shown Table Note that this control lowest precedence only effective when GPIOn_PU, GPIOn_PD, AIF_TRIS, AIFSEL ALRCGPIO1 allow GPIO functionality that GPIO pin.
March 2009,
Production Data
WM8990
REGISTER ADDRESS (13h) (14h) 11:8 (15h) (16h) LABEL GPIO1_DEB_ENA GPIO1_IRQ_ENA GPIO1_PU GPIO1_PD GPIO1_SEL[3:0] GPIO4_DEB_ENA GPIO4_IRQ_ENA GPIO4_PU GPIO4_PD GPIO4_SEL[3:0] GPIO3_DEB_ENA GPIO3_IRQ_ENA GPIO3_PU GPIO3_PD GPIO3_SEL[3:0] GPIO5_DEB_ENA GPIO5_IRQ_ENA GPIO5_PU GPIO5_PD GPIO5_SEL[3:0] GPI8_DEB_ENA GPI8_IRQ_ENA GPI8_ENA GPI7_DEB_ENA GPI7_IRQ_ENA GPI7_ENA DEFAULT 0000b 0000b 0000b 0000b Table GPIn control description Table GPIn control description Table GPIO5 control description Table GPIO3 control description Table GPIO4 control description DESCRIPTION Table GPIO1 control description
Table GPIO Control
March 2009,
WM8990
following table describes coding fields listed Table REGISTER ADDRESS Registers (13h) (15h) (See Table LABEL GPIOn_DEB_ENA DEFAULT
Production Data
DESCRIPTION De-Bounce disabled (Not de-bounced) enabled (Requires MCLK input TOCLK_ENA Enable disabled enabled GPIO Pull-Up Resistor Enable Pull-up disabled Pull-up enabled (Approx 150k) GPIO Pull-Down Resistor Enable Pull-down disabled Pull-down enabled (Approx 150k) GPIOn Function Select 0000 Input 0001 Clock output (SYSCLK/OPCLKDIV) 0010 Logic 0011 Logic 0100 Lock output 0101 Temperature output 0110 SDOUT data output 0111 output 1000 Detect 1001 Short Circuit Detect 1010 1111 Reserved GPIn Input Enable disabled GPIn input enabled GPIn input
GPIOn_IRQ_ENA GPIOn_PU GPIOn_PD GPIOn_SEL[3:0]
Table 0000b
GPIn_ENA Table GPIO Function Control Bits
polarity GPIO/GPI inputs configured using GPIO_POL register bits. This described Table REGISTER ADDRESS (17h) LABEL GPIO_POL [7:0] (rw) DEFAULT DESCRIPTION GPIOn Input Polarity Non-inverted Inverted GPIO_POL[7] GPI8 polarity GPIO_POL[6] GPI7 polarity GPIO_POL[5] Reserved GPIO_POL[4] GPIO5 polarity GPIO_POL[3] GPIO4 polarity GPIO_POL[2] GPIO3 polarity GPIO_POL[1] Reserved GPIO_POL[0] GPIO1 polarity
Table GPIO Polarity
Each available GPIO functions described turn following sections.
March 2009,
Production Data
WM8990
ALTERNATIVE INTERFACE
WM8990 configured select between different audio interfaces, providing capability receive input data BCLK2, DACLRC2 DACDAT2 instead BCLK, DACLRC DACDAT. This selection made register AIF_SEL, described Table alternative interface, following register settings required: AIF_TRIS AIF_SEL GPIO3_PU GPIO4_PU GPIO5_PU GPIO3_PD GPIO4_PD GPIO5_PD
Note that additional devices also connected main interface pins using mode. "Digital Audio Interface" section further details controlling audio interface pins. alternative interface connection illustrated Figure
DIGITAL AUDIO INTERFACE
A-law u-law support Support
GPIO
Alternative Interface Button Control Accessory Detect Clock Output
AIF_SEL
Processor
Figure Alternative Interface
Processor
GPIO3/BCLK2 GPIO4/DACLRC2 GPIO5/DACDAT2
March 2009,
DACDAT
ADCDAT
DACLRC
ADCLRC/GPIO1
BCLK
WM8990
BUTTON CONTROL
Production Data
WM8990 GPIO supports button control detection with full status readback seven inputs (and output). inputs latched Register, with de-bounce available normal operation. De-bouncing disabled order allow device respond wake-up events while processor disabled unable provide clock de-bouncing. enable button control accessory detection, following register settings required: ALRCGPIO1 (only required using GPIO1) AIF_SEL (only required using GPIO3, GPIO4 GPIO5) LMN3 LLI3LO RLI3LO (only required using GPI7) RMN3 RRI3LO RI3RO (only required using GPI8) AIF_TRIS GPIOn_SEL 0000 each required GPIO button input
Programmable pull-up pull-down resistors available GPIO1 GPIO3 GPIO5. These should according external circuit configuration. Note that pull-up pull-down resistors available GPI7 GPI8 input pins. Note that analogue input paths GPI7 GPI8 must disabled described above when using these digital inputs. this application, more GPIO pins configured Interrupt event desired. This controlled GPIOn_IRQ_ENA bits described Table GPIO status fields contained Register (R18) read time else response Interrupt event. Table more details Interrupt function. example configuration button control GPIO function illustrated Figure
ADCLRC/GPIO1
BCLK2/GPIO3
Figure Example Button Control Using GPIO Pins
Note: GPIOs referenced DBVDD GPIs referenced AVDD
DACLRC2/GPIO4
DACDAT2/GPIO5
March 2009,
Production Data
WM8990
MICBIAS CURRENT ACCESSORY DETECT
MICBIAS current detect function provided accessory detection. When microphone current detected (e.g. when headset inserted), interrupt event generated microphone status read back control interface. MICBIAS current detect threshold programmable. short-circuit current detection also available, with programmable threshold. These functions enabled register MCD; thresholds programmable register fields MCDTHR MCDSCTR shown Table Current detect short circuit detect thresholds subject temperature, supply part-to-part variation. This should factored into application design. polarity current detect GPIO signals controlled register bits MICDET_POL MICSHRT_POL. Note that these polarity inversion bits apply Interrupt register behaviour only; they affect direct GPIO output Current Detect functions. respective interrupt events masked enabled register bits MICDET_IRQ_ENA MICSHRT_IRQ_ENA. MICBIAS current threshold status bits contained Register (R18) read time else response Interrupt event. Table more details Interrupt function. direct output
Other recent searches
UJ-6 - UJ-6 UJ-6 Datasheet
SUR22D - SUR22D SUR22D Datasheet
PSA4905A - PSA4905A PSA4905A Datasheet
MAX2648 - MAX2648 MAX2648 Datasheet
KSD1020 - KSD1020 KSD1020 Datasheet
KSB810 - KSB810 KSB810 Datasheet
KP-2012PBC-A - KP-2012PBC-A KP-2012PBC-A Datasheet
ACSC04-41SEKWA-F01 - ACSC04-41SEKWA-F01 ACSC04-41SEKWA-F01 Datasheet
2SA1331 - 2SA1331 2SA1331 Datasheet
2SC3361 - 2SC3361 2SC3361 Datasheet
Privacy Policy | Disclaimer
© 2012 Datasheet Archive
