LC4105V Overview CMOS Level Shifter Package Dimens

The Datasheet Archive - 100 Million Datasheets from 7500 Manufacturers.

LC4105V Overview CMOS Level Shifter Package Dimens

Datasheet Thumbnail

Top Searches for this datasheet

Ordering number EN5641A
LC4105V
Overview
CMOS
Level Shifter
Package Dimensions
unit:
LC4105V level shifter driver that converts signals into signals with amplitudes between
3191-SSOP30
[LC4105V]
Features
Seven inputs eleven outputs produce only true outputs. produce both true inverted outputs. Slim SSOP-30 package
SANYO: SSOP30
Specifications
Absolute Maximum Ratings 25°C 2°C, voltages relative VSS, unless otherwise specified
Parameter Symbol Power supply voltage VDD1 VSS1 Input voltage Power dissipation Storage temperature Tstg 75°C Conditions Ratings -0.3 -0.3 -0.3 -0.3 -0.5 +0.3 +0.5 +125 Unit
SANYO Semiconductor products described contained herein have specifications that handle applications that require extremely high levels reliability, such life-support systems, aircraft's control systems, other applications whose failure reasonably expected result serious physical and/or material damage. Consult with your SANYO Semiconductor representative nearest before usingany SANYO Semiconductor products described contained herein such applications. SANYO Semiconductor assumes responsibility equipment failures that result from using products values that exceed, even momentarily, rated values (such maximum ratings, operating condition ranges, other parameters) listed products specifications SANYO Semiconductor products described contained herein.
TOKYO OFFICE Tokyo Bldg., 1-10, Chome, Ueno, Taito-ku, TOKYO, 110-8534 JAPAN
43098HA(OT)/13097HA(OT) 5641-1/6
LC4105V Allowable Operating Ranges voltages relative
Parameter Symbol Power supply voltage VDD1 VSS1 High-level input voltage VIN-H VIN-L Topr (VCC (VCC (VCC (VCC Conditions Ratings Unit
Low-level input voltage Operating temperature
Note: Applications must observe directions note page power power off.
Electrical Characteristics 25°C ±2°C, voltages relative VSS, unless othrewise specified
Parameter High-level input current Low-evel input current High-level output voltage Low-level output voltage Output resistance Current drain while idling Symbol Rout ICCI IDDI* ICCa Current drain during operation IDDa* Conditions VDD1 VDD1 outputs open. VDD1 Load VDD-1 0.01 0.10 VSS+1 Ratings Unit
Note: IDDI IDDa total currents flowing into power supply pins VDD1.
5641-2/6
LC4105V Assignment Block Diagram
Descriptions
Name OUT1 OUT2 OUT3 OUT4 OUT4* OUT5 OUT5* OUT6 OUT6* OUT7 OUT7* VDD1 VSS1 Number Function
Level shifter outputs
Level shifter inputs
Level shifter high-voltage power supply Buffer high-voltage power supply Level shifter low-voltage power supply Buffer ground Level shifter ground connect anything these pins.
5641-3/6
LC4105V Switching Characteristics 25°C ±2°C, ±10%,
Parameter Symbol tpLH(1) tpHL(1) Propagation delay tpLH(2) tpHL(2) Rising time Falling time Load Load Load tpHL(1)-10 tpLH(1)-20 Conditions Ratings Unit
tpHL(1)+20 tpLH(1)+10
25°C ±2°C,
Parameter Symbol tpLH(1) tpHL(1) Propagation delay tpLH(2) tpHL(2) Rising time Falling time Load Load Load Conditions Ratings Unit
Note: typical values measured OUT1 output with
Load
5641-4/6
LC4105V Power Supply Circuits
Keep impedance VSS1 lines possible. Connect large electrolytic capacitor across VDD1 VSS1 pins close Wherever possible, keep grounds power supply circuits signal circuits separate connect single point. Notes Power-Supply Voltage Application This power supply systems: (VDD1) VCC, requires that applications observe notes provided here when applying removing these voltages. particular, (VDD1) system power-supply voltage becomes higher than system voltage while system voltage established (i.e. less than VCCmin), excessive currents flow destroyed. prevent destruction this phenomenon, applications must, basically, follow sequence described item below when turning power supplies off. When turning power first apply voltage (bring this voltage value above VCCmin), then apply voltage. When turning power off, first drop voltage, and, after below VCCmin, then drop voltage.
Power-supply voltage
VDD,VDD1
Time
5641-5/6
LC4105V However, there many cases where possible control power-supply voltage on/off sequence. This actually capable supporting on/off sequence described item below. (VDD1) turned essentially same time, difference between (e.g. distance figure marked must held under while less than equal
Power-supply voltage VDD,VDD1
Time
Another point that certain amount time required stabilize system when first applied easily destroyed during this period. Inversely, when power removed, system state easily retained result device cannot destroyed easily. actual use, consider there certain amount margin removing (VDD1) voltage even after already been dropped. However, this margin varies with sample-to-sample variations itself with details application circuit, careful analysis consideration actual usage conditions required assure that will destroyed sequences items observed. Note that when power turned then immediately turned back again, many circuit designs fail meet conditions sequences described items above. sure take this into account when designing applications that this
Specifications SANYO Semiconductor products described contained herein stipulate performance, characteristics, functions described products independent state, guarantees performance, characteristics, functions described products mounted customer's products equipment. verify symptoms states that cannot evaluated independent device, customer should always evaluate test devices mounted customer's products equipment. SANYO Semiconductor Co., Ltd. strives supply high-quality high-reliability products. However, semiconductor products fail with some probability. possible that these probabilistic failures could give rise accidents events that could endanger human lives, that could give rise smoke fire, that could cause damage other property. When designing equipment, adopt safety measures that these kinds accidents events cannot occur. Such measures include limited protective circuits error prevention circuits safe design, redundant design, structural design. event that SANYO Semiconductor products (including technical data,services) described contained herein controlled under applicable local export control laws regulations, such products must exported without obtaining export license from authorities concerned accordance with above law. part this publication reproduced transmitted form means, electronic mechanical, including photocopying recording, information storage retrieval system, otherwise, without prior written permission SANYO Semiconductor Co., Ltd. information described contained herein subject change without notice product/technology improvement, etc. When designing equipment, refer "Delivery Specification" SANYO Semiconductor product that intend use. Information (including circuit diagrams circuit parameters) herein example only; guaranteed volume production. SANYO Semiconductor believes information herein accurate reliable, guarantees made implied regarding infringements intellectual property rights other rights third parties.
This catalog provides information April, 1998. Specifications information herein subject change without notice.
5641-6/6

LC4105V Overview CMOS Level Shifter Package Dimens

Top Searches for this datasheet

Other recent searches