Download

PDF Abstract Text:

Power Switching Semiconductor Products

Littelfuse Circuit Prot Solutions Portf

PRODUCT CATALOG & DESIGN GUIDE
Power Switching Semiconductor Products
Littelfuse Circuit Prot Solutions Portf
DESIGN SUPPORT
Live Application Design and Technical Support-Tap into our expertise. Littelfuse engineers are available around the world to help you address design challenges and develop unique, customized solutions for your products. Product Sampling Programs-Most of our products are available as samples for testing and verification within your circuit design. Visit Littelfuse.com or contact a Littelfuse product representative for additional information. Product Evaluation Labs and Services-Littelfuse global labs are the hub of our new product development initiatives, and also provide design and compliance support testing as an added-value to our customers.
Consumer Electronics Telecom White Goods Medical Equipment TVSS and Power S
OVERVOLTAGE SUPPRESSION TECHNOLOGIES (1-6)
1. TVS Diodes - Suppress overvoltage transients such as Electrical Fast Transients (EFT), inductive load switching and lightning in a wide variety of applications in the computer, industrial, telecom and automotive markets. 2. Varistors - Multiple forms, from Metal Oxide Varistors (MOVs) that suppress transient voltages to Multi-Layer Varistors (MLVs) designed for applications requiring protection from various transients in computers and handheld devices as well as industrial and automotive applications. 3. SIDACtor® Devices- Complete line of protection thyristor products specifically designed to suppress overvoltage transients in a broad range of telecom and datacom applications. 4. Gas Plasma Arrestors (GDTs) - Available in small footprint leaded and surface mount configurations, Littelfuse GDTs respond fast to transient overvoltage events, reducing the risk of equipment damage. 5. Silicon Protection Arrays - Designed specifically to protect analog and digital signal lines from electrostatic discharge (ESD) and other overvoltage transients. 6. PulseGuard® ESD Suppressors - Available in various surface mount form factors to protect high-speed digital lines without causing signal distortion.
Visit
tection folio
SWITCHING TECHNOLOGIES
Switching Thyristors- Solid-state switches used to control the flow of electrical current in applications, capable of withstanding rated blocking / off-state voltage until triggered to on-state.
ACCESSORIES
In addition to our broad portfolio of circuit protection technologies, we offer an array of fuse holders including circuit board, panel or in-line wire mounted devices to support a wide range of application requirements.
Supplies Lighting General Electronics
OVERCURRENT PROTECTION TECHNOLOGIES (7-8)
7. Positive Temperature Coefficient Devices (PTCs)- Provide resettable overcurrent protection for a wide range of applications.
8. Fuses - Full range including surface mount, axial, glass or ceramic, thin-film or Nano2® style, fast-acting or SloBlo®, MINI® and ATO ® fuses.
www.littelfuse.com for more information.
Circuit Protection with Thyristor Voltage Suppressors
Littelfuse Thyristors are solid state switches that are normally open circuits (very high impedance), capable of withstanding rated blocking / off-state voltage until triggered to on state. They are commonly used to control the flow of electrical currents to protect electronics from damaging voltage transients. Thyristors can be used to protect a wide range of electronic components and are commonly used in home appliances, electrical tools, and outdoor equipment. They are also often used in variable-speed electric motors, power supplies for electrochemical processes, lighting and heating control, and controllers for electric utility power systems. The Littelfuse line of Thyristors include Sensitive Triacs, Triacs, Quadrac® Devices, Alternistor Triacs, Sensitive SCRs, SCRs, Rectifiers, DIACs and SIDACs.
Features
High Voltage and Ampere ratings Unidirectional and Bidirectional transient voltage protection Automatically triggered "off" for specified periods of time RoHS compliant Glass-passivated junctions High voltage capability - up to 1000 V High surge capability - up to 950 A
Teccor® brand Thyristors
TABLE OF CONTENTS
Introduction: Thyristor Products Overview and Selection Guides Product Selection Table Product Descriptions Circuit Requirement Diagram Product Packages Quality and Reliability Assurance V-I Characteristics of Thyristor Devices Electrical Parameter Terminology Product Data Sheet Sections Data Sheet Table of Conents Triacs Quadracs SCRs SIDACs DIACs Rectifiers Appendix 1: Lead Form Dimensions Appendix 2: Application Notes Fundamental Characteristics of Thyristors Gating, Latching, and Holding of SCRs and Triacs Phase Control Using Thyristor Mounting and Handling of Semiconductor Devices Surface Mount Soldering Recommendations Thyristor and Rectifier Testing Using Curve Tracers Thyristors Used as AC Static Switches and Relays Explanation of Maximum Ratings and Characteristics Miscellaneous Design Tips and Facts Thyristors for Ignition of Fluorescent Lamps Appendix 3: Cross Reference
(AN1001) (AN1002) (AN1003) (AN1004) (AN1005) (AN1006) (AN1007) (AN1008) (AN1009) (AN1010)
DIAC, SIDAC & Rectifier Products
SCR Product Products
Triac & Quadrac Products
Reference
Teccor® brand Thyristors
Product Selection Guide
Disclaimers Life support applications These products are not designed for use in life support appliances, devices, or systems where malfunction of these products can reasonably be expected to result in personal injury. Littelfuse customers using or selling these products for use in such applications do so at their own risk and agree to fully indemnify Littelfuse for any damage resulting from such applications. Right to make changes Littelfuse reserves the right to make any and all changes to the products described herein in order to improve design and / or performance. When the product is in full production, relevant changes will be communicated via a Product / Process Change Notification (PCN). Littelfuse assumes no responsibility or liability for the use of any of these products, conveys no license or title under any patent, copyright, or mask work right to these products, and makes no representations or warranties that these products are free from patent, copyright, or mask work right infringement, unless otherwise specified.
Teccor® brand Thyristors
Product Selection Guide
PRODUCT SELECTION TABLE
Type Standard SERIES Sensitive Alternistor Datasheet Page # QxX8Ex QxXx LxX8Ex, LxXx, Qx01Ex QxNx Lx01Ex LxNx
Qxx04xx L01 Lxx04xx
Qxx06xx Lxx06xx
Qxx08xx Lxx08xx
Qxx10xx
Qxx15xx
Qxx25xx
Qxx35xx Qxx40xx
QxxxxLT
Qxx06xHx Qxx08xHx
Qxx10xHx Qxx12xHx Qxx16xHx Qxx25xHx HQ6025xH5 Qxx35xHx
QxxxxLTH
TO-92
TO-220
Thru-Hole Packages
TO-220 Isl., TO-220 Non-Isl., TO-251 TO-252, TO-263 1.0 A 800 V 3 to 10 mA
TO-220 Isl., TO-220 Non-Isl.,
Surface Mount Packages IT(RMS) VDRM / VRRM IGT (Q1)
SOT-223, Compak 0.08 A 600 V 3 to 25 mA 0.08 A 600 V 3 to 5 mA
TO-252 1.0 A 600 V 3 to 25 mA
TO-263 4A 400 to 1000 V 3 to 25 mA
TO-263 6A 400 to 1000 V 5 to 50 mA
TO-218 Isl. TO-220 Isl TO-220 Isl TO-218X Isl TO-220 Isl TO-218X Isl TO-220 Isl TO-220 TO-220 Isl TO-220 TO-218 Isl TO-218 Isl TO-220 TO-218 TO-220 Isl Non-Isl TO-220 Non-Isl TO-218X Isl TO-218 Non-Isl TO-218X TO-218 Isl Non-Isl. TO-3 Non-Isl TO-3 TO-3 TO-3 TO-263 TO-263 ----- ----- TO-263 TO-263 TO-263 TO-263 Isl 8A 400 to 1000 V 5 to 50 mA 10 A 400 to 1000 V 25 to 50 mA 12 A 400 to 1000 V 10 to 50 mA 15 & 16 A 400 to 1000 V 10 to 80 mA 25 A 1000 V 50 to 80 mA 25 A 600 V 50 mA 30 & 35 A 400 to 800 V 50 mA 40 A 400 to 1000 V 80 to 100 mA
Standard SERIES Sensitive Datasheet Page # Thru-Hole Packages EC103xx SxX8xSx SxSx
Sx01E SxN1 TCR22-x
Sxx06x
Sxx08x
Sxx10x
Sxx12x
Sxx15x Sxx16x
Sxx20x Sxx25x
Sxx35x
Sxx40x
Sxx55x
Sxx65x & Sxx70x
Sx02xS Sxx04xSx Sxx06xSx Sxx08xSx Sxx10xSx
TO-92
TO-251 TO-251 TO-251 TO-251 TO-251 TO-220 TO-220 TO-220 TO-220 TO-220 Isl TO-220 Isl TO-220 Isl Non Isl TO-252 4A TO-252 6A TO-252 8A TO-252 10 A TO-252 12 A 400 to 1000 V 20 mA
TO-220 TO-220 TO-220 TO-218X Non Isl TO-218X TO-220 Isl Non Isl TO-220 Isl TO-218AC TO-218X TO-218AC TO-218AC TO-252 TO-263 TO-263 ------ 35 A 400 to 1000 V 40 mA TO-263 40 A 400 to 1000 V 40 mA TO-263 55 A 400 to 1000 V 40 mA ------ 65 & 70 A 400 to 1000 V 50 mA
Surface Mount Packages IT(RMS) VDRM / VRRM IGT (Q1)
SOT-89Compak SOT223 Compak Compak 0.8 A 0.8 A 1A 400 to 600 V 10 mA 400 to 400 to 600 V 800 V 12 to 500 5 to 20 mA mA
TO-252 1A 400 to 600 V 10 mA
SOT-223 1.5 A 400 to 600 V
400 to 400 to 400 to 400 to 600 V 1000 V 1000 V 1000 V 50 to 500 0.2 to 15 0.2 to 15 0.2 to 15 200 mA mA mA mA mA
SIDAC
Kxxxzy-307
Multipulse SIDAC
Kxxx1G MP
HTxxx HTMxxx STxxx
Rectifiers
Dxx15L Dxx20L Dxx25L
Kxxx0yH
SERIES Datasheet Page # Thru-Hole Package IF(RMS) IF(AV) RMS forward current Average forward current
DO-15, TO-92 DO-214 79 to 280 V ----- ----- 150 mA 20 A 1500 V / us N / A 150 A / us up to 125 C
DO-15 TO-92 DO-214 190 to 280 V ----- ----- 160 mA typ
DO-15 DO-214 190 to 280 V ----- ----- 150 mA
DO-35 SOD-80 Minimelf DO-214 27 to 70 V down to 1V up to 10 V ----- ----- ----- I2t Tstg TJ
Peak non-repetitive surge current
225 - 350A
I2t Value for fusing Storage temperature range Operating junction temperature range
210 - 508 A2s -40 to 150 °C -40 to 125 °C
100 us
Specifications are subject to change without notice. Please refer to http://www.littelfuse.com for current information.
DIAC, SIDAC & Rectifier Products DIAC, SIDAC & Rectifier Products
High Energy SIDAC
SCR Product Products SCR
Sensitive SCR & Non-Sensitive SCR
Triac & Quadrac Products Triac & Quadrac Products
Sensitive Triac, Triac, & Alternistor Triac
Quadrac
Introduction Reference
Teccor® brand Thyristors
Product Selection Guide
Product Descriptions
Teccor® brand Thyristors
Product Selection Guide
Because of its unidirectional switching capability, the SCR is used in circuits where high surge currents or latching action is required. It may also be used for half-wavetype circuits where gate-controlled rectification action is required. Applications include crowbars in power supplies, camera flash units, smoke alarms, motor controls, battery chargers, and engine ignition. Surge current ratings are available from 30 A in the TO-92 packaging to 950 A in the TO-218X package. Rectifiers Littelfuse manufactures 15 A to 25 A rms Rectifiers with voltages rated from 400 V to 1000 V. Due to the electrically isolated TO-220 package, these Rectifiers may be used in common anode or common cathode circuits using only one part type, thereby simplifying stock requirements. DIACs DIACs are trigger devices used in phase control circuits to provide gate pulses to a Triac or SCR. They are voltagetriggered bidirectional silicon devices housed in DO-35 glass axial lead packages and DO-214 surface mount packages. DIAC voltage selections from 27 V to 70 V provide trigger pulses closely matched in symmetry at the positive and negative breakover points to minimize DC component in the load circuit. Some applications include gate triggers for light controls, dimmers, power pulse circuits, voltage references in AC power circuits, and Triac triggers in motor speed controls. SIDACs SIDACs represent a unique set of Thyristor qualities. The SIDAC is a bidirectional voltage triggered switch. Some characteristics of this device include a normal 95 V to 330 V switching point, negative resistance range, latching characteristics at turn-on, and a low on-state voltage drop. One-cycle surge current capability up to 20 A makes the SIDAC an ideal product for dumping charged capacitors through an inductor in order to generate high-voltage pulses. Applications include light controls, high-pressure sodium lamp starters, power oscillators, and high-voltage power supplies.
Circuit Requirement Diagram
BILATERAL VOLTAGE SWITCH RECTIFIER REVERSE BLOCKING THYRISTOR BIDIRECTIONAL THYRISTOR BILATERAL VOLTAGE TRIGGER
SIDAC
RECTIFIER
GATE CURRENT 5-500 A 10-50 mA
GATE CONTROL DIAC TRIGGER DIRECT
SCR (Sensitive)
OPTIONS INTERNAL EXTERNAL
QUADRANT OPERATION (See Quadrant Chart on Data Sheet) I II III I II III IV
DIACS QUADRAC
GATE CURRENT 5-100 mA
GATE CURRENT 3-20 mA
ALTERNISTOR TRIAC
STANDARD TRIAC
SENSITIVE TRIAC
For detailed information, see specific data sheet in product catalog.
Introduction
Teccor® brand Thyristors
Product Selection Guide
Product Packages
Surface-Mount Package Code Y G E MM B S C T D N
Current (Amps) 0.8 1 Sensitive 4 Triac 6 8 0.8 1 4 6 Standard 8 Triac 10 15 25 35 6 8 10 12 Alternistor 16 25 30 35 40 4 6 8 Quadrac 10 15 0.8 1.5 4 Sensitive SCR 6 8 10 1 6 8 10 12 15 16 SCR 20 25 35 40 55 65 70 15 Rectifier 20 25 DIAC SIDAC
Product Type
DO-35
DO-15
TO-92 X X
MiniMELF
SOT-89
DO-214
Compak X X
SOT-223 X X
TO-252 D-Pak
TO-263 D2Pak
Teccor® brand Thyristors
Product Selection Guide
Isolated Mounting Tab L K J P V
Non-isolated Mounting Tab Package Code M W R
TO-220
TO-218
TO-218X
TO-3 Fastpak
TO-251 V-Pak
TO-218
TO-218X
TO-220
Current Product (Amps) Type 0.8 1 Sensitive 4 Triac 6 8 0.8 1 4 6 Standard 8 Triac 10 15 25 35 6 8 10 12 16 Alternistor 25 30 35 40 4 6 8 Quadrac 10 15 0.8 1.5 4 Sensitive SCR 6 8 10 1 6 8 10 12 15 16 SCR 20 25 35 40 55 65 70 15 20 Rectifier 25 DIAC SIDAC
Introduction
Teccor® brand Thyristors
Product Selection Guide
Quality and Reliability Assurance
Teccor® brand Thyristors
Product Selection Guide
Reliability Stress Tests The following table contains brief descriptions of the reliability tests commonly used in evaluating Littelfuse
product reliability on a periodic basis. These tests are applied across product lines depending on product availability and test equipment capacities. Other tests may be performed when appropriate.
High Temperature Storage Life
MIL -STD-750 (Method 1031)
Biased Temperature & Humidity
EIA / JEDEC, JESD22-A101
Temperature Cycle Air to Air
-65°C to 150°C, 15-minute dwell, 10 up to 500 cycles
MIL -STD-750 (Method 1051), EIA / JEDEC, JESD22-A104
Thermal Shock Liquid to Liquid
0°C to 100°C, 5-minute dwell, 10-second transfer, 10 cycles
MIL -STD-750 (Method 1056)
Autoclave (PCT)
EIA / JEDEC, JESD22-A102
Resistance to Solder Heat
260°C, 10 seconds
MIL -STD-750 (Method 2031)
Solderability Lead Bend Moisture Sensitivity Level ESD
ANSI J-STD-002 MIL -STD-750 (Method 2036) JEDEC J-STD-020 Level 1 JESD22-A114, MIL -STD-883D 3015.7 JESD22-C101 ,
Flammability Test For the UL 94V0 flammability test, all epoxies used in Littelfuse encapsulated devices are recognized by Underwriters Laboratories.
Introduction
Teccor® brand Thyristors
Product Selection Guide
V-I Characteristics of Thyristor Devices
Voltage Drop (vT) at Specified Current (iT)
Latching Current (IL)
Off-state Leakage Current - (IDRM) at Specified VDRM
IS IDRM IBO +V VBO
Minimum Holding Current (IH)
Specified Minimum Off-state Blocking Voltage (VDRM)
(VBO - VS) (IS - IBO)
VS VDRM
Breakover Voltage
Characteristics of Triac Device
Voltage Drop (VT) at Specified Current (iT)
Characteristics of SIDAC Device with Negative Resistance
Latching Current (IL)
Reverse Leakage Current - (IRRM) at Specified VRRM
Off - State Leakage Current - (IDRM) at Specified VDRM
Minimum Holding Current (IH)
Breakover Current IBO
Specified Minimum Reverse Blocking Voltage (VRRM)
Specified Minimum Off - State Blocking Voltage (VDRM)
Breakover Voltage VBO
Reverse Breakdown Voltage
Forward Breakover Voltage
Characteristics of SCR Device
Characteristics of Bilateral Trigger DIAC
Teccor® brand Thyristors
Product Selection Guide
Diode Rectifiers di / dt (Critical Rate-of-rise of On-state Current) - Maximum value of the rate-of-rise of on-state current which a Thyristor can withstand without deleterious effect. dv / dt (Critical Rate-of-rise of Off-state Voltage or Static dv / dt) - Minimum value of the rate-of-rise of principal voltage which will cause switching from the off state to the on state. dv / dt(c) Critical Rate-of-rise of Commutation Voltage of a Triac (Commutating dv / dt) - Minimum value of the rateof-rise of principal voltage which will cause switching from the off state to the on state immediately following on-state current conduction in the opposite quadrant. I2t (RMS Surge (Non-repetitive) On-state Fusing Current)Measure of let-through energy in terms of current and time for fusing purposes. IBO(Breakover Current) - Principal current at the breakover point. IDRM(Repetitive Peak Off-state Current) - Maximum leakage current that may occur under the conditions of VDRM. IGT(Gate Trigger Current) - Minimum gate current required to switch a Thyristor from the off state to the on state. IH (Holding Current) - Minimum principal current required to maintain the Thyristor in the on state. IPP (Peak Pulse Current) - Peak pulse current at a short time duration and specified waveshape. IRRM (Repetitive Peak Reverse Current) - Maximum leakage current that may occur under the conditions of VRRM. IS (Switching Current) - Current at VS when a SIDAC switches from the clamping state to on state. IT(RMS) (On-state Current) - Anode cathode principal current that may be allowed under stated conditions, usually the fullcycle RMS current. ITSM (Surge (Non-repetitive) On-state Current) - Peak single cycle AC current pulse allowed. PG(AV) (Average Gate Power Dissipation) - Value of gate power which may be dissipated between the gate and main terminal 1 (or cathode) average over a full cycle. PGM (Peak Gate Power Dissipation) - Maximum power which may be dissipated between the gate and main terminal 1 (or cathode) for a specified time duration. R JA (Thermal Resistance, Junction-to-Ambient) Temperature difference between the Thyristor junction and ambient divided by the power dissipation causing the temperature difference under conditions of thermal equilibrium. Note: Ambient is defined as the point where temperature does not change as a result of the dissipation.
Introduction
Electrical Parameter Terminology
Teccor® brand Thyristors
Product Selection Guide
Teccor® brand Thyristors
Product Selection Guide
DATA SHEET TABLE OF CONTENTS
0.8A EV 0.8A 1.0A EV 1.0A 4.0A 6.0A 8.0A 10.0A 12.0A 15 / 16.0A 25.0A 25.0A 30 / 35.0A 40A
LxX8Ex & LxXx & QxX8Ex & QxXx LX8 Lx01Ex & LxNx & Qx01Ex & QxNx L01 Lxx04xx & Qxx04xx Lxx06xx & Qxx06xx & Qxx06xHx Lxx08xx & Qxx08xx & Qxx08xHx Qxx10xx & Qxx10xHx Qxx12xHx Qxx15xx & Qxx16xHx Qxx25xx & Qxx25xHx HQ6025xH5 Series Qxx30xHx & Qxx35xx & Qxx35xHx Qxx40xx
Sensitive & Standard Triacs Sensitive Triacs Sensitive & Standard Triacs Sensitive Triacs Sensitive & Standard Triacs Sensitive, Standard, & Alternistor (High Commutation) Triacs Sensitive, Standard, & Alternistor (High Commutation) Triacs Standard & Alternistor (High Commutation) Triacs Alternistor (High Commutation) Triacs Standard & Alternistor (High Commutation) Triacs Standard & Alternistor (High Commutation) Triacs High Temperature Alternistor Triacs Standard & Alternistor (High Commutation) Triacs Alternistor (High Commutation) Triacs
Quadracs
Silicon Controlled Rectifiers (SCRs)
0.8 A EV 0.8 A 1.0 A 1.5 A EV 1.5 A 4.0 A 6.0 A 8.0 A 10.0 A 12.0 A 15 / 16.0A 20 / 25 A 35 A 40 A 55 A 65 / 70 A EC103xx & SxSx SxX8xSx Sx01E & SxN1 TCR22-x Sx02xS Sxx04xSx Sxx06xSx & Sxx06x Sxx08xSx & Sxx08x Sxx10xSx & Sxx10x Sxx12x Sxx15x & Sxx16x Sxx20x & Sxx25x Sxx35x Sxx40x Sxx55x Sxx65x & Sxx70x Sensitive SCRs Sensitive SCRs Standard SCRs Sensitive SCRs Sensitive SCRs Sensitive SCRs Sensitive & Standard SCRs Sensitive & Standard SCRs Sensitive & Standard SCRs Standard SCRs Standard SCRs Standard SCRs Standard SCRs Standard SCRs Standard SCRs Standard SCRs 163 173 183 193 201 209 217 227 239 249 257 265 275 283 291 301
SIDACs
79 - 280 V 190 - 280 V 190 -280 V Kxxxzy Kxxx0yH Kxxx1G Standard Bidirectional SIDAC High Energy Bidirectional SIDAC Multipulse SIDAC 309 321 331
DIACs
27 - 70V HTxxx & HTMxxx & STxxx Standard Bidirectional DIAC Trigger 337
Rectifiers
15 / 20 / 25 A Dxx15L & Dxx20L & Dxx25L Rectifiers 345
DIAC, SIDAC & Rectifier Products
SCR Product Products
QUADRACs
Triac & Quadrac Products
Triacs
Introduction
Teccor® brand Thyristors
Product Selection Guide
Teccor® brand Thyristors
0.8 Amp Sensitive & Standard Triacs
LxX8Ex & LxXx & QxX8E & QxXx Series
Description 0.8 Amp bi-directional solid state switch series is designed for AC switching and phase control applications such as motor speed and temperature modulation controls, lighting controls, and static switching relays.
Standard type devices normally operate in Quadrants I & III triggered from AC line.
Features 600 V junctions
Symbol IT(RMS) VDRM / VRRM IGT (Q1) Value 0.8 400 to 600 3 to 25 Unit A V mA
Main Features
10 A Applications Excellent for lower current heating controls, water valves, and solenoids. Typical applications are AC solid-state switches, home / brown goods and white goods appliances.
Schematic Symbol
Sensitive gate Triacs can be directly driven by microprocessor or popular opto-couplers / isolators.
Absolute Maximum Ratings - Sensitive Triacs (4 Quadrants)
LxX8Ex & LxXx & QxX8Ex & QxXx Series
0.8 A TRIACs
Sensitive type devices guarantee gate control in Quadrants I & IV needed for digital control circuitry.
Teccor® brand Thyristors
0.8 Amp Sensitive & Standard Triacs
Absolute Maximum Ratings - Standard Triac
Operating junction temperature range
Symbol IGT VGT VGD IH dv / dt (dv / dt)c tgt
Test Conditions
Quadrant I - II - III MAX. TYP . MAX. MIN. MAX. 400V 600V MIN. TYP . TYP .
QxX8E3 QxX3 10 25 1.3 0.2 15 25 15 1 2.5
QxX8E4 QxX4 25 50 1.3 0.2 25 35 25 1 3.0
LxX8Ex & LxXx & QxX8Ex & QxXx Series
Teccor® brand Thyristors
0.8 Amp Sensitive & Standard Triacs
Thermal Resistances
Symbol R R Parameter Junction to case (AC) Junction to ambient L / QxX8Ey L / QxXy L / QxX8Ey Value 60 60 135 Unit °C / W °C / W
(J-C)
(J-A)
Figure 1: Definition of Quadrants
ALL POLARITIES ARE REFERENCED TO MT1 MT2 POSITIVE (Positive Half Cycle)
Figure 2: Normalized DC Gate Trigger Current for All Quadrants vs. Junction Temperature
IGT GATE
REF MT2 IGT GATE MT1 REF
QII QI QIII QIV
MT2 IGT GATE MT1 REF
Ratio of
MT2 NEGATIVE (Negative Half Cycle)
LxX8Ex & LxXx & QxX8Ex & QxXx Series
0.8 A TRIACs
Teccor® brand Thyristors
0.8 Amp Sensitive & Standard Triacs
Figure 3: Normalized DC Holding Current vs. Junction Temperature
Figure 4: Normalized DC Gate Trigger Voltage for All Quadrants vs. Junction Temperature
Ratio of
Figure 5: Power Dissipation (Typical) vs. RMS On-State Current
Figure 6: Maximum Allowable Case Temperature vs. On-State Current
130 120 CURRENT WAVE FORM: Sinusoidal LOAD: Resistive or Inductive CONDUCTION ANGLE: 360° CASE TEMPERATURE: Measured as shown on Dimensional Drawing
Average On-State Power Dissipation (PD(AV)) - Watts
CURRENT WAVE FORM: Sinusoidal LOAD: Resistive or Inductive CONDUCTION ANGLE: 360° 0.8
Maximum Allowable Case Temperature (TC) - °C
QxX8Ex / QxXx 110 100 90 80 LxX8Ex / LxXx 70 60
RMS On-State Current (IT(RMS)) - Amps
Figure 7: Maximum Allowable Ambient Temperature vs. On-State Current
120 CURRENT WAVEFORM: Sinusoidal LOAD: Resistive or Inductive CONDUCTION ANGLE: 360° FREE AIR RATING - NO HEATSINK
Figure 8: On-State Current vs. On-State Voltage (Typical)
Maximum Allowable Ambient Temperature (TA) - °C
On-State Current (IT) - Amps
RMS On-State Current (IT(RMS)) - Amps
On-State Voltage (VT) - Volts
LxX8Ex & LxXx & QxX8Ex & QxXx Series
Teccor® brand Thyristors
0.8 Amp Sensitive & Standard Triacs
Figure 9: Surge Peak On-State Current vs. Number of Cycles
Peak Surge (Non-repetitive) On-State Current (ITSM ) - Amps
Supply Frequency: 60Hz Sinusoidal Load: Resistive RMS On-State IT(RMS): Max Rated Value at Specific Case Temperature Notes: 1. Gate control may be lost during and immediately following surge current interval. 2. Overload may not be repeated until junction temperature has returned to steady-state rated value.
Surge Current Duration - Full Cycles
Soldering Parameters
Reflow Condition - Temperature Min (Ts(min)) Pre Heat - Temperature Max (Ts(max)) - Time (min to max) (ts) Average ramp up rate (Liquidus Temp) (TL) to peak TS(max) to TL - Ramp-up Rate Reflow - Temperature (TL) (Liquidus) - Temperature (tL) Pb - Free assembly
Temperature
150°C 200°C 60 - 190 secs 5°C / second max 5°C / second max 217°C 60 - 150 seconds 260
Ramp-up
TL TS(max)
Preheat
Ramp-do Ramp-down
TS(min)
25 time to peak temperature
Peak Temperature (TP) Time within 5°C of actual peak Temperature (tp) Ramp-down Rate Time 25°C to peak Temperature (TP) Do not exceed
20 - 40 seconds 5°C / second max 8 minutes Max. 280°C
LxX8Ex & LxXx & QxX8Ex & QxXx Series
0.8 A TRIACs
Teccor® brand Thyristors
0.8 Amp Sensitive & Standard Triacs
Physical Specifications
Environmental Specifications
Thermal Shock
Autoclave Resistance to Solder Heat Solderability Lead Bend
Dimensions - TO-92 (E Package)
TC Measuring Point
Inches Min 0.176 0.500 0.095 0.150 0.046 0.135 0.088 0.176 0.088 0.013 0.013 0.054 0.145 0.096 0.186 0.096 0.019 0.017 0.105 Max 0.196
Millimeters Min 4.47 12.70 2.41 3.81 1.16 3.43 2.23 4.47 2.23 0.33 0.33 1.37 3.68 2.44 4.73 2.44 0.48 0.43 2.67 Max 4.98
Cathode / MT1 / PIN 1 Gate / PIN 2
Anode / MT2 / PIN 3
All leads insulated from case. Case is electrically nonconductive.
LxX8Ex & LxXx & QxX8Ex & QxXx Series
Teccor® brand Thyristors
0.8 Amp Sensitive & Standard Triacs
Dimensions - Compak (C Package)
TC / TL Temperature Measurement Point B D M N Gate
Dimension A B C
Inches Min 0.140 0.205 0.077 0.166 0.036 0.066 0.004 0.077 0.043 0.008 0.039 0.022 0.027 0.052 Max 0.155 0.220 0.083 0.180 0.063 0.083 0.008 0.086 0.053 0.012 0.049 0.028 0.033 0.058
Millimeters Min 3.56 5.21 1.96 4.22 0.91 1.67 0.10 1.96 1.09 0.20 0.99 0.56 0.69 1.32 Max 3.94 5.59 2.11 4.57 1.60 2.11 0.20 2.18 1.35 0.30 1.24 0.71 0.84 1.47
MT1 / Cathode MT2 / Anode
K 0.079 (2.0) 0.079 (2.0)
Pad Outline
Dimensions are in inches (and millimeters).
Product Selector
Part Number LxX8E3 LxX3 LxX8E5 LxX5 LxX8E6 LxX8E8 QxX8E3 QxX3 QxX8E4 QxX4
Gate Sensitivity Quadrants I - II - III 3 mA 3 mA 5 mA 5 mA 5 mA 10 mA 10 mA 10 mA 25 mA 25 mA IV 3 mA 3 mA 5 mA 5 mA 10 mA 20 mA
Type Sensitive Triac Sensitive Triac Sensitive Triac Sensitive Triac Sensitive Triac Sensitive Triac Standard Triac Standard Triac Standard Triac Standard Triac
Package TO-92 Compak TO-92 Compak TO-92 TO-92 TO-92 Compak TO-92 Compak
Packing Options
Part Number L / QxX8Ey L / QxX8EyRP L / QxX8EyAP L / QxXyRP
Marking L / QxX8Ey L / QxX8Ey L / QxX8Ey L / QxXy
Weight 0.188 g 0.188 g 0.188 g 0.081 g
Packing Mode Bulk Reel Pack Ammo Pack Embossed Carrier
Base Quantity 2000 2000 2000 2500
LxX8Ex & LxXx & QxX8Ex & QxXx Series
0.8 A TRIACs
Teccor® brand Thyristors
0.8 Amp Sensitive & Standard Triacs
TO-92 (3-lead) Reel Pack (RP) Radial Leaded Specifications Meets all EIA-468-B 1994 Standards
0.098 (2.5) MAX
0.354 (9.0) 0.5 (12.7) 0.1 (2.54) 14.17(360.0) MT1 / Cathode 0.2 (5.08) Gate MT2 / Anode 0.157 DIA (4.0)
Flat up
1.97 (50.0) Dimensions are in inches (and millimeters).
Direction of Feed
TO-92 (3-lead) Ammo Pack (AP) Radial Leaded Specifications Meets all EIA-468-B 1994 Standards
0.098 (2.5) MAX
0.354 (9.0) 0.5 (12.7) 0.1 (2.54) MT2 / Anode 0.2 (5.08) MT1 / Cathode 0.157 (4.0) DIA
Flat down
Directio n of Fee d
25 Devices per fold
12.2 (310.0) Dimensions are in inches (and millimeters).
LxX8Ex & LxXx & QxX8Ex & QxXx Series
Teccor® brand Thyristors
0.8 Amp Sensitive & Standard Triacs
Compak Embossed Carrier Reel Pack (RP) Specifications Meets all EIA-481-1 Standards
0.157 (4.0) 0.47 (12.0) Anode / MT2
0.36 (9.2) 8.0 0.315 (8.0) Gate Cathode / MT1
0.059 DIA (1.5)
Cover tape
0.512 (13.0) Arbor Hole Dia.
12.99 (330.0) Dimensions are in inches (and millimeters).
Direction of Feed
Part Numbering System
DEVICE TYPE L : Sensitive Triac Q : Triac SENSITIVITY & TYPE Sensitive Triac: 3 : 3 mA (QI, II, III, IV) 5 : 5 mA (QI, II, III, IV) 6 : 5 mA (QI, II, III) 10 mA (QIV) 8 : 10 mA (QI, II, III) 20 mA (QIV) Standard Triac: 3 : 10 mA (QI, II, III) 4 : 25 mA (QI, II, III)
Part Marking System
TO-92 (E Package)
L4X8E3
Compak (C Package)
L4X3 yxxxx
yxxxx
VOLTAGE RATING 4 : 400V 6 : 600V
CURRENT RATING X8 : 0.8A (TO-92) X : 0.8A (Compak)
PACKAGE TYPE Blank : Compak (Surface Mount) E : TO-92
LxX8Ex & LxXx & QxX8Ex & QxXx Series
0.8 A TRIACs
Teccor® brand Thyristors
EV Series 0.8 Amp Sensitive Triacs
LX8 Series
Symbol IT(RMS) VDRM / VRRM IGT Value 0.8 400 to 600 3 to 5 Unit A V mA
mount packages
Applications The LX8 EV Series is especially designed for low current applications such as heating controls in hair care products, as well as replacement of mechanical switch contacts where long life is required.
Schematic Symbol
Absolute Maximum Ratings
LX8 Series
EV 0.8A TRIACs
Teccor® brand Thyristors
EV Series 0.8 Amp Sensitive Triacs
(dv / dt)c
Thermal Resistances
Rth(j-a)
Junction to ambient
LX8 Series
Teccor® brand Thyristors
EV Series 0.8 Amp Sensitive Triacs
Figure 1: Definition of Quadrants
Figure 2: Normalized DC Gate Trigger Current for All Quadrants vs. Junction Temperature
ALL POLARITIES ARE REFERENCED TO MT1 MT2 POSITIVE (Positive Half Cycle)
IGT GATE MT1
IGT GATE
MT2 IGT GATE MT1 REF
IGT GATE MT1 REF
MT2 NEGATIVE (Negative Half Cycle)
Ratio of
QII QI QIII QIV
Junction Temperature (TJ) °C
Figure 3: Normalized DC Holding Current vs. Junction Temperature
Figure 4: Normalized DC Gate Trigger Voltage for All Quadrants vs. Junction Temperature
Ratio of
Junction Temperature (TJ) °C
Figure 5: Power Dissipation (Typical) vs. RMS On-State Current
Figure 6: Maximum Allowable Case Temperature vs. On-State Current
130 CURRENT WAVEFORM: Sinusoidal LOAD: Resistive or Inductive CONDUCTION ANGLE: 360o CASE TEMPERATURE: Measured as shown on dimensional drawings
Average On-state Power Dissipation PD(AV) - Watts
CURRENT WAVEFORM: Sinusoidal LOAD: Resistive or Inductive CONDUCTION ANGLE: 360°
Maximum Allowable Case Temperature (TC ) - °C
120 110 SOT-223
100 90 80 TO-92 70 60 50
RMS On-state Current IT(RMS) - Amps
LX8 Series
EV 0.8A TRIACs
Teccor® brand Thyristors
EV Series 0.8 Amp Sensitive Triacs
Figure 7: Surge Peak On-State Current vs. Number of Cycles
Peak Surge (Non-repetitive) On-State Current (ITSM) - Amps.
Supply Frequency: 60Hz Sinusoidal Load: Resistive RMS On-State Current IT(RMS): Max Rated Value at Specific Case Temperature Notes: 1. Gate control may be lost during and immediately following surge current interval. 2. Overload may not be repeated until junction temperature has returned to steady-state rated value.
Surge Current Duration - Full Cycle
Soldering Parameters
Reflow Condition - Temperature Min (Ts(min)) Pre Heat - Temperature Max (Ts(max)) - Time (min to max) (ts) Average ramp up rate (Liquidus Temp) (TL) to peak TS(max) to TL - Ramp-up Rate Reflow - Temperature (TL) (Liquidus) - Time (min to max) (ts) Pb - Free assembly
Temperature
Ramp-up
150°C 200°C 60 - 180 secs 5°C / second max 5°C / second max 217°C 60 - 150 seconds 260+0 / -5 °C 20 - 40 seconds 5°C / second max 8 minutes Max. 280°C
TL TS(max)
Preheat
Ramp-do Ramp-down
TS(min)
25 time to peak temperature
Peak Temperature (TP) Time within 5°C of actual peak Temperature (tp) Ramp-down Rate Time 25°C to peak Temperature (TP) Do not exceed
LX8 Series
Teccor® brand Thyristors
EV Series 0.8 Amp Sensitive Triacs
Physical Specifications
Reliability / Environmental Tests
Test AC Blocking Specifications and Conditions MIL-STD-750, M-1040, Cond A Applied Peak AC voltage @ 110°C for 1008 hours MIL-STD-750, M-1051, 100 cycles -40°C to +150°C 15-min dwell-time
Temperature Cycling
High Temp Storage Low-Temp Storage
Thermal Shock
Autoclave Resistance to Solder Heat Solderability Lead Bend
Dimensions - TO-92 (E Package)
Dimensions A B C D E F G H I J Inches Min 0.175 0.170 0.500 0.135 0.125 0.080 0.016 0.045 0.095 0.015 Typ - - - 0.165 - 0.095 - 0.050 0.100 - Max 0.205 0.210 - - 0.165 0.105 0.021 0.055 0.105 0.020 Min 4.450 4.320 12.700 3.430 3.180 2.040 0.407 1.150 2.420 0.380 Millimeters Typ - - - 4.190 - 2.400 - 1.270 2.540 - Max 5.200 5.330 - - 4.190 2.660 0.533 1.390 2.660 0.500
LX8 Series
EV 0.8A TRIACs
Temperature / Humidity
Teccor® brand Thyristors
EV Series 0.8 Amp Sensitive Triacs
Dimensions - SOT-223
Pad Layout for SOT-223
Dimensions A B C
Inches Min 0.248 0.130 - 0.001 0.114 0.024 - - 0.264 0.009 Typ 0.256 0.138 - - 0.118 0.027 0.090 0.181 0.276 0.010 Max 0.264 0.146 0.071 0.004 0.124 0.034 - - 0.287 0.014 Min 6.30 3.30 - 0.02 2.90 0.60 - - 6.70 0.24
Millimeters Typ 6.50 3.50 - - 3.00 0.70 2.30 4.60 7 .00 0.26 Max 6.70 3.70 1.80 0.10 3.15 0.85 - - 7 .30 0.35
1.2 (0.047") (3x) 1.5 (0.059")
Dimensions in Millimeters (Inches)
Product Selector
Part Number LX803DE LX803ME LX803DT LX803MT LX807DE LX807ME LX807DT LX807MT Voltage 400 V 600 V 400 V 600 V 400 V 600 V 400 V 600 V Gate Sensitivity Quadrants I - II - III 3 mA 3 mA 3 mA 3 mA 5 mA 5 mA 5 mA 5 mA IV 5 mA 5 mA 5 mA 5 mA 7 mA 7 mA 7 mA 7 mA Package TO-92 TO-92 SOT-223 SOT-223 TO-92 TO-92 SOT-223 SOT-223
Packing Options
Part Number LX8xxyE LX8xxyEAP LX8xxyERP LX8xxyTRP Marking LX8xxyE LX8xxyE LX8xxyE LX8xxyT Weight 0.170 g 0.170 g 0.170 g 0.120 g Packing Mode Bulk Ammo Pack Tape & Reel Tape & Reel Base Quantity 2500 2000 2000 1000
LX8 Series
Teccor® brand Thyristors
EV Series 0.8 Amp Sensitive Triacs
TO-92 (3-lead) Reel Pack (RP) Radial Leaded Specifications Meets all EIA-468-B 1994 Standards
0.098 (2.5) MAX
0.354 (9.0) 0.5 (12.7) 0.1 (2.54) 14.17(360.0) MT1 / Cathode 0.2 (5.08) MT2 / Anode 0.157 DIA (4.0)
Flat up
1.97 (50.0) Dimension s are in inches (and millimeters).
Direction of Feed
TO-92 (3-lead) Ammo Pack (AP) Radial Leaded Specifications Meets all EIA-468-B 1994 Standards
0.098 (2.5) MAX
0.354 (9.0) 0.5 (12.7) 0.1 (2.54) MT2 / Anod e 0.2 (5.08) MT1 / Cathod e 0.157 (4.0) DIA
Flat down
n Directio of Feed
25 Devices per fold
12.2 (310.0) Dimensions are in inche s (and millimeters).
LX8 Series
EV 0.8A TRIACs
Teccor® brand Thyristors
EV Series 0.8 Amp Sensitive Triacs
SOT-223 Reel Pack (RP) Specifications
1.5 mm
1.75 mm
5.5 mm
180 mm 13 mm Abor Hole Diameter
13.4 mm
Part Numbering System
Part Marking System
TRIAC SERIES
CURRENT X8: 0.8A SENSITIVITY & TYPE 03: 3, 3, 3, 5mA Triac 07: 5, 5, 5, 7mA Triac
PACKING TYPE Blank: Bulk Pack RP : Reel Pack (TO-92) : Embossed Carrier Pack (SOT-223) AP : Ammo Pack (TO-92) PACKAGE TYPE E: TO-92 T: SOT-223 VOLTAGE D: 400V M: 600V
LX8 Series
Teccor® brand Thyristors
1 Amp Sensitive & Standard Triacs
Lx01Ex & LxNx & Qx01Ex & QxNx Series
Description 1 Amp bi-directional solid state switch series is designed for AC switching and phase control applications such as motor speed and temperature modulation controls, lighting controls, and static switching relays.
Standard type devices normally operate in Quadrants I & III triggered from AC line. Features & Benefits 20 A junctions
Symbol IT(RMS) VDRM / VRRM IGT (Q1) Value 1 400 to 600 3 to 25 Unit A V mA
Main Features
600 V Applications Excellent for lower current heating controls, water valves, and solenoids. Typical applications are AC solid-state switches, home / brown goods and white goods appliances.
Schematic Symbol
Sensitive gate Triacs can be directly driven by microprocessor or popular opto-couplers / isolators.
Absolute Maximum Ratings - Sensitive Triacs (4 Quadrants)
Lx01Ex & LxNx & Qx01Ex & QxNx Series
1.0A TRIACs
Sensitive type devices guarantee gate control in Quadrants I & IV needed for digital control circuitry.
Teccor® brand Thyristors
1 Amp Sensitive & Standard Triacs
Absolute Maximum Ratings - Standard Triacs
Operating junction temperature range
Lx01Ex & LxNx & Qx01Ex & QxNx Series
Teccor® brand Thyristors
1 Amp Sensitive & Standard Triacs
Thermal Resistances
Symbol R R Parameter Junction to case (AC) Junction to ambient L / Qx01Ey L / QxNy L / Qx01Ey Value 50 40 95 Unit °C / W °C / W
(J-C)
(J-A)
Figure 1: Definition of Quadrants
ALL POLARITIES ARE REFERENCED TO MT1 MT2 POSITIVE (Positive Half Cycle)
Figure 2: Normalized DC Gate Trigger Current for All Quadrants vs. Junction Temperature
I GT GATE MT1
REF MT2 I GT GATE MT1 REF
QII QI QIII QIV
MT2 I GT GATE MT1 REF
MT2 NEGATIVE (Negative Half Cycle)
Lx01Ex & LxNx & Qx01Ex & QxNx Series
1.0A TRIACs
Teccor® brand Thyristors
1 Amp Sensitive & Standard Triacs
Figure 3: Normalized DC Holding Current vs. Junction Temperature
Figure 4: Normalized DC Gate Trigger Voltage for All Quadrants vs. Junction Temperature
Figure 5: Power Dissipation (Typical) vs. RMS On-State Current
Figure 6: Maximum Allowable Case Temperature vs. On-State Current
Average On-State Power Dissipation (PD(AV)) - Watts
120 110 100 90 80 70 60 50 0 0.2 0.4 Lx01Ex / LxNx
CURRENT WAVE FORM: Sinusoidal LOAD: Resistive or Inductive CONDUCTION ANGLE: 360° 1.0
RMS On-State Current (IT(RMS)) - Amps
RMS On-State Current IT(RMS) - AMPS
Figure 7: Maximum Allowable Ambient Temperature vs. On-State Current
Figure 8: On-State Current vs. On-State Voltage (Typical)
Positive or Negative Instantaneous On-State Current (IT) - AMPS
RMS On-State Current IT(RMS) - AMPS
Positive or Negative Instantaneous On-State Voltage (VT) - Volts
Lx01Ex & LxNx & Qx01Ex & QxNx Series
Teccor® brand Thyristors
1 Amp Sensitive & Standard Triacs
Figure 9: Surge Peak On-State Current vs. Number of Cycles
Peak Surge (Non-repetitive) On-State Current (ITSM ) - Amps
Supply Frequency: 60Hz Sinusoidal Load: Resistive RMS On-State IT(RMS): Max Rated Value at Specific Case Temperature Notes: 1. Gate control may be lost during and immediately following surge current interval. 2. Overload may not be repeated until junction temperature has returned to steady-state rated value.
Surge Current Duration - Full Cycles
Soldering Parameters
Reflow Condition - Temperature Min (Ts(min)) Pre Heat - Temperature Max (Ts(max)) - Time (min to max) (ts) Average ramp up rate (Liquidus Temp) (TL) to peak TS(max) to TL - Ramp-up Rate Reflow - Temperature (TL) (Liquidus) - Temperature (tL) Pb - Free assembly
Temperature
150°C 200°C 60 - 190 secs 5°C / second max 5°C / second max 217°C 60 - 150 seconds 260°C 20 - 40 seconds 5°C / second max 8 minutes Max. 280°C
25 time to peak temperature Ramp-up
TL TS(max)
Preheat
Ramp-do Ramp-down
TS(min)
Peak Temperature (TP) Time within 5°C of actual peak Temperature (tp) Ramp-down Rate Time 25°C to peak Temperature (TP) Do not exceed
Lx01Ex & LxNx & Qx01Ex & QxNx Series
1.0A TRIACs
Teccor® brand Thyristors
1 Amp Sensitive & Standard Triacs
Physical Specifications
Environmental Specifications
Thermal Shock
Autoclave Resistance to Solder Heat Solderability Lead Bend
Dimensions - Compak (C Package)
TC / TL Temperature Measurement Point B D M N Gate
Dimension A
Inches Min 0.140 0.205 0.077 0.166 0.036 0.066 0.004 0.077 0.043 0.008 0.039 0.022 0.027 0.052 Max 0.155 0.220 0.083 0.180 0.063 0.083 0.008 0.086 0.053 0.012 0.049 0.028 0.033 0.058
Millimeters Min 3.56 5.21 1.96 4.22 0.91 1.67 0.10 1.96 1.09 0.20 0.99 0.56 0.69 1.32 Max 3.94 5.59 2.11 4.57 1.60 2.11 0.20 2.18 1.35 0.30 1.24 0.71 0.84 1.47
MT1 / Cathode MT2 / Anode
K 0.079 (2.0) 0.079 (2.0)
Pad Outline
Dimensions are in inches (and millimeters).
Lx01Ex & LxNx & Qx01Ex & QxNx Series
Teccor® brand Thyristors
1 Amp Sensitive & Standard Triacs
Dimensions - TO-92 (E Package)
TC Measuring Point
Dimension
Inches Min 0.176 0.500 0.095 0.150 0.046 0.135 0.088 0.176 0.088 0.013 0.013 Max 0.196 0.105 0.054 0.145 0.096 0.186 0.096 0.019 0.017
Millimeters Min 4.47 12.70 2.41 3.81 1.16 3.43 2.23 4.47 2.23 0.33 0.33 Max 4.98 2.67 3.68 2.44 4.73 2.44 0.48 0.43 1.37
Cathode / MT1 / PIN 1 Gate / PIN 2
Anode / MT2 / PIN 3
All leads insulated from case. Case is electrically nonconductive.
Product Selector
Part Number Lx01E3 LxN3 Lx01E5 LxN5 Lx01E6 Lx01E8 Qx01E3 QxN3 Qx01E4 QxN4
Note: x- voltage
Gate Sensitivity Quadrants I - II - III 3 mA 3 mA 5 mA 5 mA 5 mA 10 mA 10 mA 10 mA 25 mA 25 mA IV 3 mA 3 mA 5 mA 5 mA 10 mA 20 mA
Type Sensitive Triac Sensitive Triac Sensitive Triac Sensitive Triac Sensitive Triac Sensitive Triac Standard Triac Standard Triac Standard Triac Standard Triac
Package TO-92 Compak TO-92 Compak TO-92 TO-92 TO-92 Compak TO-92 Compak
Packing Options
Part Number L / Qx01Ey L / Qx01EyRP L / Qx01EyAP L / QxNyRP
Marking L / Qx01Ey L / Qx01Ey L / Qx01Ey L / QxNy
Weight 0.188 g 0.188 g 0.188 g 0.081 g
Packing Mode Bulk Reel Pack Ammo Pack Embossed Carrier
Base Quantity 2000 2000 2000 2500
Lx01Ex & LxNx & Qx01Ex & QxNx Series
1.0A TRIACs
Teccor® brand Thyristors
1 Amp Sensitive & Standard Triacs
TO-92 (3-lead) Reel Pack (RP) Radial Leaded Meets all EIA-468-B 1994 Standards
0.098 (2.5) MAX
0.354 (9.0) 0.5 (12.7) 0.1 (2.54) 14.17(360.0) MT1 / Cathode 0.2 (5.08) Gate MT2 / Anode 0.157 DIA (4.0)
Flat up
1.97 (50.0) Dimensions are in inches (and millimeters).
Direction of Feed
TO-92 (3-lead) Ammo Pack (AP) Radial Leaded Meets all EIA-468-B 1994 Standards
0.098 (2.5) MAX
0.354 (9.0) 0.5 (12.7) 0.1 (2.54) MT2 / Anode 0.2 (5.08) MT1 / Cathode Gate 0.157 (4.0) DIA
Directio
n of Feed
Flat down
25 Devices per fold
12.2 (310.0) Dimensions are in inches (and millimeters).
Lx01Ex & LxNx & Qx01Ex & QxNx Series
Teccor® brand Thyristors
1 Amp Sensitive & Standard Triacs
Compak Embossed Carrier Reel Pack (RP) Meets all EIA-481-1 Standards
0.157 (4.0) 0.47 (12.0) 0.36 (9.2) 8.0 0.315 (8.0) Gate Cover tape Anode / MT2
Cathode / MT1
0.059 DIA (1.5)
0.512 (13.0) Arbor Hole Dia.
Dimensions are in inches (and millimeters).
Direction of Feed
Part Numbering System
DEVICE TYPE L : Sensitive Triac Q : Triac SENSITIVITY & TYPE Sensitive Triac: 3 : 3 mA (QI, II, III, IV) 5 : 5 mA (QI, II, III, IV) 6 : 5 mA (QI, II, III) 10 mA (QIV) 8 : 10 mA (QI, II, III) 20 mA (QIV) Standard Triac: 3 : 10 mA (QI, II, III) 4 : 25 mA (QI, II, III)
Part Marking System TO-92 (E Package)
L401E3
Compak (C Package)
L4N3 yxxxx
yxxxx
VOLTAGE RATING 4 : 400V 6 : 600V
CURRENT RATING 01 : 1.0A (TO-92) N : 1.0A (Compak)
PACKAGE TYPE Blank : Compak (Surface Mount) E : TO-92
Lx01Ex & LxNx & Qx01Ex & QxNx Series
1.0A TRIACs
Teccor® brand Thyristors
EV Series 1 Amp Sensitive Triacs
L01 Series
Description New 1 Amp bi-directional solid state switch series offering direct interface to microprocessor drivers in economical TO-92 and surface mount packages. The die voltage blocking junctions are glass-passivated to ensure long term reliability and parametric stability. Features sec mount packages 10Amps Main Features
Symbol IT(RMS) VDRM / VRRM IGT Value 1 400 to 800 3 to 10 Unit A V mA
) capability - up to 800V
Applications The L01 EV Series is especially designed for white goods applications such as valve controls in washing machines as well as replacement of mechanical and hybrid relays where long life is required. Schematic Symbol
Absolute Maximum Ratings
Unit A
I2t Value for fusing
di / dt IG PG(AV) Tstg TJ
L01 Series
Specifications are subject to change without notice. Please refer to http://www.littelfuse.com for current information.
EV 1.0 A TRIACs
Teccor® brand Thyristors
EV Series 1 Amp Sensitive Triacs
(dv / dt)c
Thermal Resistances
Rth(j-a)
Junction to ambient
L01 Series
Teccor® brand Thyristors
EV Series 1 Amp Sensitive Triacs
Figure 1: Definition of Quadrants
Figure 2: Normalized DC Gate Trigger Current for All Quadrants vs. Junction Temperature
ALL POLARITIES ARE REFERENCED TO MT1 MT2 POSITIVE (Positive Half Cycle)
IGT GATE
MT2 IGT GATE
Ratio of
REF MT2 IGT GATE MT1 REF
QII QI QIII QIV
MT2 NEGATIVE (Negative Half Cycle)
MT1 REF
Figure 3: Normalized DC Holding Current vs. Junction Temperature
Figure 4: Normalized DC Gate Trigger Voltage for All Quadrants vs. Junction Temperature
Ratio of
Junction Temperature (TJ)- °C
Figure 5: Power Dissipation (Typical) vs. RMS On-State Current
Figure 6: Maximum Allowable Case Temperature vs. On-State Current
130 125 120 110 100 90 80 70 60 50 0.0 0.1 0.2 0.3 0.4 0.5 0.6 0.7 0.8 0.9 1.0 1.1 1.2 TO-92 SOT-223
CURRENT WAVEFORM: Sinusoidal LOAD: Resistive or Inductive CONDUCTION ANGLE: 360° CASE TEMPERATURE: Measured as shown on dimensional drawings
Average On-state Power Dissipation PD(DAV) - Watts
CURRENT WAVEFORM: Sinusoidal LOAD: Resistive or Inductive CONDUCTION ANGLE: 360°
RMS On-state Current IT(RMS) - Amps
L01 Series
EV 1.0 A TRIACs
Teccor® brand Thyristors
EV Series 1 Amp Sensitive Triacs
Figure 7: Surge Peak On-State Current vs. Number of Cycles
Peak Surge (Non-repetitive) On-State Current (ITSM) - Amps.
Supply Frequency: 60Hz Sinusoidal Load: Resistive RMS On-State Current IT(RMS): Max Rated Value at Specific Case Temperature Notes: 1. Gate control may be lost during and immediately following surge current interval. 2. Overload may not be repeated until junction temperature has returned to steady-state rated value.
Surge Current Duration - Full Cycle
Soldering Parameters
Reflow Condition - Temperature Min (Ts(min)) Pre Heat - Temperature Max (Ts(max)) - Time (min to max) (ts) Average ramp up rate (Liquidus Temp) (TL) to peak TS(max) to TL - Ramp-up Rate Reflow - Temperature (TL) (Liquidus) - Time (min to max) (ts) Pb - Free assembly
Temperature
150°C 200°C 60 - 180 secs 5°C / second max 5°C / second max 217°C 60 - 150 seconds 260
Ramp-up
TL TS(max)
Preheat
Ramp-do Ramp-down
TS(min)
25 time to peak temperature
Peak Temperature (TP) Time within 5°C of actual peak Temperature (tp) Ramp-down Rate Time 25°C to peak Temperature (TP) Do not exceed
20 - 40 seconds 5°C / second max 8 minutes Max. 280°C
L01 Series
Teccor® brand Thyristors
EV Series 1 Amp Sensitive Triacs
Physical Specifications
Environmental Specifications
Test AC Blocking Specifications and Conditions MIL-STD-750, M-1040, Cond A Applied Peak AC voltage @ 125°C for 1008 hours MIL-STD-750, M-1051, 100 cycles -40°C to +150°C 15-min dwell-time
Temperature Cycling
High Temp Storage Low-Temp Storage
Thermal Shock
Autoclave Resistance to Solder Heat Solderability Lead Bend
Dimensions - TO-92 (E Package)
Dimensions A B C D E F G H I J Inches Min 0.175 0.170 0.500 0.135 0.125 0.080 0.016 0.045 0.095 0.015 Typ - - - 0.165 - 0.095 - 0.050 0.100 - Max 0.205 0.210 - - 0.165 0.105 0.021 0.055 0.105 0.020 Min 4.450 4.320 12.700 3.430 3.180 2.040 0.407 1.150 2.420 0.380 Millimeters Typ - - - 4.190 - 2.400 - 1.270 2.540 - Max 5.200 5.330 - - 4.190 2.660 0.533 1.390 2.660 0.500
L01 Series
EV 1.0 A TRIACs
Temperature / Humidity
Teccor® brand Thyristors
EV Series 1 Amp Sensitive Triacs
Dimensions - SOT-223
Dimensions Pad Layout for SOT-223
Inches Min 0.248 0.130 - 0.001 0.114 0.024 - - 0.264 0.009 Typ 0.256 0.138 - - 0.118 0.027 0.090 0.181 0.276 0.010 Max 0.264 0.146 0.071 0.004 0.124 0.034 - - 0.287 0.014 Min 6.30 3.30 - 0.02 2.90 0.60 - - 6.70 0.24
Millimeters Typ 6.50 3.50 - - 3.00 0.70 2.30 4.60 7 .00 0.26 Max 6.70 3.70 1.80 0.10 3.15 0.85 - - 7 .30 0.35
1.2 (0.047") (3x) 1.5 (0.059")
Dimensions in Millimeters (Inches)
10° MAX
Product Selector
Part Number L0103DE L0103ME L0103NE L0103DT L0103MT L0103NT L0107DE L0107ME L0107NE L0107DT L0107MT L0107NT L0109DE L0109ME L0109NE L0109DT L0109MT L0109NT
L01 Series
Voltage 400 V 600 V 800 V 400 V 600 V 800 V 400 V 600 V 800 V 400 V 600 V 800 V 400 V 600 V 800 V 400 V 600 V 800 V
Gate Sensitivity Quadrants I II III IV 3 mA 3 mA 3 mA 3 mA 3 mA 3 mA 5 mA 5 mA 5 mA 5 mA 5 mA 5 mA 10 mA 10 mA 10 mA 10 mA 10 mA 10 mA
Package TO-92 TO-92 TO-92 SOT-223 SOT-223 SOT-223 TO-92 TO-92 TO-92 SOT-223 SOT-233 SOT-233 TO-92 TO-92 TO-92 SOT-223 SOT-223 SOT-223
Specifications are subject to change without notice. Please refer to http://www.littelfuse.com for current information.
Teccor® brand Thyristors
EV Series 1 Amp Sensitive Triacs
Packing Options
Part Number L01xxyE L01xxyEAP L01xxyERP L01xxyTRP
Marking L01xxyE L01xxyE L01xxyE L01xxyT
Weight 0.170 g 0.170 g 0.170 g 0.120 g
Packing Mode Bulk Ammo Pack Tape & Reel Tape & Reel
Base Quantity 2500 2000 2000 1000
TO-92 (3-lead) Reel Pack (RP) Radial Leaded Specifications Meets all EIA-468-B 1994 Standards
0.098 (2.5) MAX
0.354 (9.0) 0.5 (12.7) 0.1 (2.54) 14.17(360.0) MT2 / Anode MT1 / Cathode 0.2 (5.08) Gate
0.157 DIA (4.0)
Flat up
1.97 (50.0) Dimensions are in inches (and millimeters).
Direction of Feed
TO-92 (3-lead) Ammo Pack (AP) Radial Leaded Specifications Meets all EIA-468-B 1994 Standards
0.098 (2.5) MAX
0.354 (9.0) 0.5 (12.7) 0.1 (2.54) MT2 / Anode 0.2 (5.08) MT1 / Cathode Gate 0.157 (4.0) DIA
Directio
n of Feed
Flat down
25 Devices per fold
12.2 (310.0) Dimensions are in inches (and millimeters).
L01 Series
EV 1.0 A TRIACs
Teccor® brand Thyristors
EV Series 1 Amp Sensitive Triacs
SOT-223 Reel Pack (RP) Specifications
5.5 mm
180 mm 13 mm Abor Hole Diameter
13.4 mm
Part Numbering System
Part Marking System
TRIAC SERIES
CURRENT 01: 1A SENSITIVITY & TYPE 03: 3, 3, 3, 5mA Triac 07: 5, 5, 5, 7mA Triac 09: 10, 10, 10, 10mA Triac
PACKING TYPE Blank: Bulk Pack RP : Reel Pack (TO-92) : Embossed Carrier Pack (SOT-223) AP : Ammo Pack (TO-92) PACKAGE TYPE E: TO-92 T: SOT-223 VOLTAGE D: 400V M: 600V N: 800V
L01 Series
Teccor® brand Thyristors
4 Amp Sensitive & Standard Triacs
Lxx04xx & Qxx04xx Series
Description
4 Amp bi-directional solid state switch series is designed for AC switching and phase control applications such as motor speed and temperature modulation controls, lighting controls, and static switching relays. Sensitive type devices guarantee gate control in Quadrants I & IV needed for digital control circuitry. Standard type devices normally operate in Quadrants I & III triggered from AC line. Features & Benefits Agency Approval
Agency
contact bounce that create voltage transients
Agency File Number L Package : E71639
junctions 1000 V 55 A from reaction of switching events generation, depending on activation point of sine wave activation pulse in each half-cycle
Main Features
Symbol IT(RMS) VDRM / VRRM IGT (Q1) Value 4 400 to 1000 3 to 25 Unit A V mA
"L-Package" is UL recognized for 2500Vrms eliminates arcing or Applications
Schematic Symbol
Typical applications are AC solid-state switches, power tools, home / brown goods and white goods appliances.
Sensitive gate Triacs can be directly driven by microprocessor or popular opto-couplers / isolators. Internally constructed isolated packages are offered for ease of heat sinking with highest isolation voltage.
Absolute Maximum Ratings - Sensitive Triacs (4 Quadrants)
Symbol IT(RMS) ITSM I2t di / dt IG PG(AV) Tstg TJ
Value 4 33 40 6.6 50 1.2 0.3 -40 to 150 -40 to 110
Lxx04xx & Qxx04xx Series
4.0A TRIACs
Teccor® brand Thyristors
4 Amp Sensitive & Standard Triacs
Absolute Maximum Ratings - Standard Triacs
ITSM I2t di / dt IG PG(AV) Tstg TJ
Lxx04xx & Qxx04xx Series
Teccor® brand Thyristors
4 Amp Sensitive & Standard Triacs
Thermal Resistances
Symbol Parameter L / Qxx04Dy R
(J-C)
Value 3.5 3.6 6.0 50
Junction to case (AC)
L / Qxx04Ly L / Qxx04Ry / L / Qxx04Vy L / Qxx04Ly
(J-A)
Junction to ambient
L / Qxx04Ry / L / Qxx04Vy
Figure 1: Definition of Quadrants
Figure 2: Normalized DC Gate Trigger Current for All Quadrants vs. Junction Temperature
ALL POLARITIES ARE REFERENCED TO MT1 MT2 POSITIVE (Positive Half Cycle)
IGT GATE
MT2 IGT GATE
Ratio of
IGT GATE
QII QI QIII QIV
MT1 REF
MT2 NEGATIVE (Negative Half Cycle)
MT1 REF
Lxx04xx & Qxx04xx Series
4.0A TRIACs
Teccor® brand Thyristors
4 Amp Sensitive & Standard Triacs
Figure 3: Normalized DC Holding Current vs. Junction Temperature
Figure 4: Normalized DC Gate Trigger Voltage for All Quadrants vs. Junction Temperature
Ratio of
Figure 5: Power Dissipation (Typical) vs. RMS On-State Current
Figure 6: Maximum Allowable Case Temperature vs. On-State Current
110 105 CURRENT WAVE FORM: Sinusoidal LOAD: Resistive or Inductive CONDUCTION ANGLE: 360° CASE TEMPERATURE: Measured as shown on Dimensional Drawing
Average On-State Power Dissipation (PD(AV)) - Watts
LOAD: Resistive or Inductive CONDUCTION ANGLE: 360°
Maximum Allowable Case Temperature (TC) - °C
CURRENT WAVE FORM: Sinusoidal
Lxx04Ly Lxx04Dy
Lxx04Vyz Lxx04Ry LXX04Vy
RMS On-State Current (IT(RMS)) - Amps
Figure 7: Maximum Allowable Case Temperature vs. On-State Current
110 105 CURRENT WAVE FORM: Sinusoidal LOAD: Resistive or Inductive CONDUCTION ANGLE: 360° CASE TEMPERATURE: Measured as shown on Dimensional Drawing
Figure 8: Maximum Allowable Ambient Temperature vs. On-State Current
120 CURRENT WAVEFORM: Sinusoidal LOAD: Resistive or Inductive CONDUCTION ANGLE: 360° FREE AIR RATING - NO HEATSINK
Maximum Allowable Ambient Temperature (TA) - °C
Maximum Allowable Case Temperature (TC) - °C
Lxx04Ly Lxx04Dy
80 Qxx04Ly Qxx04Ry 60 L / Qxx04Vy 40 Lxx04Ly 20
Lxx04Vyz Lxx04Ry LXX04Vy
RMS On-State Current (IT(RMS)) - Amps
RMS On-State Current IT(RMS) - Amps
Lxx04xx & Qxx04xx Series
Teccor® brand Thyristors
4 Amp Sensitive & Standard Triacs
Figure 9: On-State Current vs. On-State Voltage (Typical)
Positive or Instantaneous On-State Current (IT) - Amps
Positive or Instantaneous On-State Voltage (VT) - Volts
Figure 10: Surge Peak On-State Current vs. Number of Cycles
Peak Surge (Non-repetitive) On-State Current (ITSM) - Amps
Qxx04Ry Qxx04Ly Qxx04Dy Qxx04Vy
Supply Frequency: 60Hz Sinusoidal Load: Resistive RMS On-State IT(RMS): Max Rated Value at Specific Case Temperature Notes: 1. Gate control may be lost during and immediately following surge current interval. 2. Overload may not be repeated until junction temperature has returned to steady-state rated value.
Lxx04Ry Lxx04Ly Lxx04Dy Lxx04Vy
Surge Current Duration - Full Cycles
Lxx04xx & Qxx04xx Series
4.0A TRIACs
Teccor® brand Thyristors
4 Amp Sensitive & Standard Triacs
Soldering Parameters
Reflow Condition - Temperature Min (Ts(min)) Pre Heat - Temperature Max (Ts(max)) - Time (min to max) (ts) Average ramp up rate (Liquidus Temp) (TL) to peak TS(max) to TL - Ramp-up Rate Reflow - Temperature (TL) (Liquidus) - Temperature (tL) Pb - Free assembly
Temperature
150°C 200°C 60 - 190 secs 5°C / second max 5°C / second max 217°C 60 - 150 seconds 260°C +0 / -5 20 - 40 seconds 5°C / second max 8 minutes Max. 280°C
25 time to peak temperature Ramp-up
TL TS(max)
Preheat
Ramp-do Ramp-down
TS(min)
Peak Temperature (TP) Time within 5°C of actual peak Temperature (tp) Ramp-down Rate Time 25°C to peak Temperature (TP) Do not exceed
Physical Specifications
Environmental Specifications
Thermal Shock
Autoclave Resistance to Solder Heat Solderability Lead Bend
Lxx04xx & Qxx04xx Series
Teccor® brand Thyristors
4 Amp Sensitive & Standard Triacs
Dimensions - TO-220AB (R-Package) - Non-Isolated Mounting Tab Common with Center Lead
TC MEASURING POINT O E A MT2 B C D 7.01 .276 13.36 .526 P 8.13 .320 AREA (REF.) 0.17 IN2
Inches Min 0.380 0.105 0.230 0.590 0.142 0.110 0.540 0.025 0.195 0.095 0.060 0.085 0.018 0.178 0.045 0.038 Max 0.420 0.115 0.250 0.620 0.147 0.130 0.575 0.035 0.205 0.105 0.075 0.095 0.024 0.188 0.060 0.048
Millimeters Min 9.65 2.67 5.84 14.99 3.61 2.79 13.72 0.64 4.95 2.41 1.52 2.16 0.46 4.52 1.14 0.97 Max 10.67 2.92 6.35 15.75 3.30 14.61 0.89 5.21 2.67 1.91 2.41 0.61 4.78 1.52 1.22 3.73
NOTCH IN GATE LEAD TO ID. NON-ISOLATED TAB
K J MT1 MT2 GATE
Note: Maximum torque to be applied to mounting tab is 8 in-lbs. (0.904 Nm).
Dimensions - TO-220AB (L-Package) - Isolated Mounting Tab
TC MEASURING POINT O E A P 8.13 .320 AREA (REF.) 0.17 IN2
Dimension A
Inches Min 0.380 0.105 0.230 0.590 0.142 0.110 0.540 0.025 0.195 0.095 0.060 0.085 0.018 0.178 0.045 0.038 Max 0.420 0.115 0.250 0.620 0.147 0.130 0.575 0.035 0.205 0.105 0.075 0.095 0.024 0.188 0.060 0.048
Millimeters Min 9.65 2.67 5.84 14.99 3.61 2.79 13.72 0.64 4.95 2.41 1.52 2.16 0.46 4.52 1.14 0.97 Max 10.67 2.92 6.35 15.75 3.73 3.30 14.61 0.89 5.21 2.67 1.91 2.41 0.61 4.78 1.52 1.22
Note: Maximum torque to be applied to mounting tab is 8 in-lbs. (0.904 Nm).
Lxx04xx & Qxx04xx Series
4.0A TRIACs
Teccor® brand Thyristors
4 Amp Sensitive & Standard Triacs
Dimensions - TO-251AA (V-Package) - V-PAK Through Hole
TC MEASURING POINT E D MT2 A 5.34 .210 B H J AREA: 0.040 IN2 5.28 .208
Inches Min 0.040 0.235 0.350 0.205 0.255 0.027 0.087 0.085 0.176 0.018 0.038 0.018 Max 0.050 0.245 0.375 0.213 0.265 0.033 0.093 0.095 0.184 0.023 0.044 0.023
Millimeters Min 1.02 5.97 8.89 5.21 6.48 0.69 2.21 2.16 4.47 0.46 0.97 0.46 Max 1.27 6.22 9.53 5.41 6.73 0.84 2.36 2.41 4.67 0.58 1.12 0.58
Dimensions - TO-252AA (D-Package) - D-PAK Surface Mount
E D MT2 A 5.34 .210 N TC MEASURING POINT 5.28 .208 O L K M J H
MT2 GATE F G I AREA : 0.040 IN2
Dimension Pad Layout for TO-252AA (D-Package)
Inches Min
Millimeters Max
Lxx04xx & Qxx04xx Series
Teccor® brand Thyristors
4 Amp Sensitive & Standard Triacs
Product Selector
Part Number Lxx04L3 Lxx04D3 Lxx04R3 Lxx04V3 Lxx04L5 Lxx04D5 Lxx04R5 Lxx04V5 Lxx04L6 Lxx04D6 Lxx04R6 Lxx04V6 Lxx04L8 Lxx04D8 Lxx04R8 Lxx04V8 Qxx04L3 Qxx04D3 Qxx04V3 Qxx04R3 Qxx04L4 Qxx04D4 Qxx04R4 Qxx04V4 Voltage 400V X X X X X X X X X X X X X X X X X X X X X X X X 600V X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X 800V 1000V Gate Sensitivity Quadrants I - II - III 3 mA 3 mA 3mA 3 mA 5 mA 5 mA 5mA 5 mA 5 mA 5 mA 5mA 5 mA 10 mA 10 mA 10mA 10 mA 10 mA 10 mA 10 mA 10mA 25 mA 25 mA 25mA 25 mA IV 3 mA 3 mA 3mA 3 mA 5 mA 5 mA 5mA 5 mA 10 mA 10 mA 10mA 10 mA 20 mA 20 mA 20mA 20 mA Type Sensitive Triac Sensitive Triac Sensitive Triac Sensitive Triac Sensitive Triac Sensitive Triac Sensitive Triac Sensitive Triac Sensitive Triac Sensitive Triac Sensitive Triac Sensitive Triac Sensitive Triac Sensitive Triac Sensitive Triac Sensitive Triac Standard Triac Standard Triac Standard Triac Standard Triac Standard Triac Standard Triac Standard Triac Standard Triac Package TO-220L TO-252 D-PAK TO-220R
TO-220L TO-252 D-PAK TO-220R TO-251 V-PAK TO-220L TO-252 D-PAK TO-220R TO-251 V-PAK TO-220L TO-252 D-PAK TO-220R TO-251 V-PAK TO-220L TO-252 D-PAK TO-251 V-PAK TO-220R TO-220L TO-252 D-PAK TO-220R TO-251 V-PAK
Packing Options
Part Number L / Q004L / Ry / TP L / Qxx04LyTP L / Qxx04DyRP L / Qxx04DyTP L / Qxx04VyTP
Marking L / Qxx04L / Ry L / Qxx04Ly L / Qxx04Dy L / Qxx04Dy L / Qxx04Vy
Weight 2.2 g 2.2 g 0.3 g 0.3 g 0.4 g
Packing Mode Bulk Tube Embossed Carrier Tube Pack Tube Pack
Base Quantity 500 500 2500 750 750
Lxx04xx & Qxx04xx Series
4.0A TRIACs
TO-251 V-PAK
Teccor® brand Thyristors
4 Amp Sensitive & Standard Triacs
TO-252 Embossed Carrier Reel Pack (RP) Specifications Meets all EIA-481-2 Stand