PHASE CONTROL THYRISTORS Hockey Version Center amplifying gate Me
|
|
|
Top Searches for this datasheet
ST230C.C SERIES
PHASE CONTROL THYRISTORS Hockey Version
Center amplifying gate Metal case with ceramic insulator International standard case TO-200AB (A-PUK)
410A
Typical Applications
motor controls Controlled power supplies controllers
Major Ratings Characteristics
Parameters
IT(AV) IT(RMS) ITSM 50Hz 60Hz 50Hz 60Hz DRM/V typical
case style TO-200AB (A-PUK)
Units
KA2s KA2s
ST230C.C
5700 5970 2000
www.irf.com
ST230C.C Series
ELECTRICAL SPECIFICATIONS Voltage Ratings
Voltage Type number Code
ST230C.C
DRM/V RRM, max. repetitive peak off-state voltage
1200 1400 1600 1800 2000
VRSM maximum nonrepetitive peak voltage
1300 1500 1700 1900 2100
DRM/I max.
On-state Conduction
Parameter
T(AV) Max. average on-state current Heatsink temperature T(RMS) Max. on-state current Max. peak, one-cycle non-repetitive surge current
ST230C.C
(165) (85) 5700 5970 4800 5000
Units Conditions
180° conduction, half sine wave double side (single side) cooled 25°C heatsink temperature double side cooled 10ms 8.3ms 10ms 8.3ms 10ms KA2s 8.3ms 10ms 8.3ms
voltage reapplied 100% VRRM reapplied voltage reapplied 100% VRRM reapplied Sinusoidal half wave, Initial max.
Maximum fusing
Maximum fusing
1630 0.92
10ms, voltage reapplied (16.7% IT(AV) IT(AV)), max.
T(TO) level value threshold voltage T(TO) High level value threshold voltage level value on-state slope resistance High level value on-state slope resistance Max. on-state voltage Maximum holding current Max. (typical) latching current
0.98 IT(AV)),TJ max. (16.7% IT(AV) IT(AV)), max. 0.81 1.69 1000 (300) 25°C, anode supply resistive load IT(AV)),TJ max. Ipk= 880A, max, 10ms sine pulse
0.88
Switching
Parameter
di/dt Max. non-repetitive rate rise turned-on current Typical delay time Typical turn-off time
ST230C.C
1000
Units Conditions
A/µs max, anode voltage VDRM Gate current g/dt 1A/µs 0.67% VDRM, 25°C 300A, max, di/dt 20A/µs, dv/dt 20V/µs, Gate 100, 500µs Gate drive 20V,
www.irf.com
ST230C.C Series
Blocking
Parameter
dv/dt IDRM IRRM Maximum critical rate rise off-state voltage Max. peak reverse off-state leakage current
ST230C.C
Units Conditions
V/µs max. linear rated VDRM max, rated applied
Triggering
Parameter
Maximum peak gate power
ST230C.C
10.0
Units Conditions
max, max, 50Hz, max,
PG(AV) Maximum average gate power +VGM -VGM Max. peak positive gate current Maximum peak positive gate voltage Maximum peak negative gate voltage TYP. gate current required trigger gate voltage required trigger gate current trigger gate voltage trigger
MAX. 0.25
max,
40°C 25°C 125°C 40°C 25°C 125°C Max. gate current/voltage trigger max. value which will trigger unit with rated VDRM anode-to-cathode applied Max. required gate trigger/ current/ voltage lowest value which will trigger units anode-to-cathode applied
Thermal Mechanical Specification
Parameter
Tstg Max. operating temperature range Max. storage temperature range
ST230C.C
0.17 0.08 0.033 0.017 4900 (500)
Units Conditions
operation single side cooled operation double side cooled operation single side cooled operation double side cooled
RthJ-hs Max. thermal resistance, junction heatsink RthC-hs Max. thermal resistance, case heatsink Mounting force,
(Kg)
Approximate weight Case style
200AB (A-PUK)
Outline Table
www.irf.com
ST230C.C Series
RthJ-hs Conduction
(The following table shows increment thermal resistence RthJ-hs when devices operate different conduction angles than
Conduction angle
180° 120°
Sinusoidal conduction Rectangular conduction
Single Side Double Side 0.015 0.018 0.024 0.035 0.060 0.017 0.019 0.024 0.035 0.060 Single Side Double Side 0.011 0.019 0.026 0.036 0.060 0.011 0.019 0.026 0.037 0.061
Units
Conditions
max.
Ordering Information Table
Device Code
Thyristor Essential part number Converter grade Ceramic Voltage code: Code VRRM (See Voltage Rating Table) Case TO-200AB (A-PUK) Eyelet terminals (Gate Auxiliary Cathode Unsoldered Leads) Fast-on terminals (Gate Auxiliary Cathode Unsoldered Leads) Eyelet terminals (Gate Auxiliary Cathode Soldered Leads) Fast-on terminals (Gate Auxiliary Cathode Soldered Leads)
Critical dv/dt: None 500V/µsec (Standard selection) 1000V/µsec (Special selection)
www.irf.com
ST230C.C Series
Outline Table
ANODE GATE CREEPAGE DISTANCE: 7.62 (0.30) MIN. STRIKE DISTANCE: 7.12 (0.28) MIN. (0.75) DIA. MAX. (0.01) MIN.
13.7 14.4 (0.54 0.57) (0.01) MIN. (0.75) DIA. MAX. (1.50) MAX. GATE TERM. 1.47 (0.06) DIA. RECEPTACLE
Case Style TO-200AB (A-PUK)
dimensions millimeters (inches) Quote between upper lower pole pieces considered after application Mounting Force (see Thermal Mechanical Specification)
HOLES 3.56 (0.14) 1.83 (0.07) MIN. DEEP (0.26) 4.75 (0.19)
25°±
(1.65) MAX. (1.10)
Maximum Allowable Heatsink Temperature (°C)
Maximum Allowable Heatsink Temperature (°C)
ST230C.C Series (Single Side Cooled) thJ-hs (DC) 0.17
ST230C.C Series (Single Side Cooled) thJ-hs (DC) 0.17
Conduction Angle
Conduction Period
120° 180°
120° 180°
Average On-state Current
Fig. Current Ratings Characteristics
Average On-state Current
Fig. Current Ratings Characteristics
www.irf.com
ST230C.C Series
Maximum Allowable Heatsink Temperature (°C) Maximum Allowable Heatsink Temperature (°C)
ST230C.C Series (Double Side Cooled) thJ-hs (DC) 0.08
ST230C.C Series (Double Side Cooled) thJ-hs (DC) 0.08
Conduction Angle
Conduction Period
120° 180°
120° 180°
Average On-state Current
Fig. Current Ratings Characteristics
Average On-state Current
Fig. Current Ratings Characteristics
Maximum Allowable Heatsink Temperature (°C)
Maximum Allowable Heatsink Temperature (°C)
1400 1200 1000
180° 120°
Limit
180° 120°
Limit Conduction Period
Conduction Angle
1000
Average On-state Current
Fig. On-state Power Loss Characteristics
ST230C.C Series 125°C
ST230C.C Series 125°C
Average On-state Current
Fig. On-state Power Loss Characteristics
Peak Half Sine Wave On-state Current
5500 5000 4500 4000 3500 3000 2500 2000
Peak Half Sine Wave On-state Current
Rated Load Condition With Rated Vrrm Applied Following Surge. Initial 125°C 0.0083 0.0100
Maximum Repetitive Surge Current Versus Pulse Train Duration. Control Conduction Maintained. Initial 125°C Voltage Reapplied Rated Vrrm Reapplied
ST230C.C Series
ST230C.C Series
0.01
Pulse Train Duration
Number Equal Amplitude Half Cycle Current Pulses Fig. Maximum Non-Repetitive Surge Current Single Double Side Cooled
Fig. Maximum Non-Repetitive Surge Current Single Double Side Cooled
www.irf.com
ST230C.C Series
10000
Instantaneous On-state Current
25°C
125°C
1000
ST230C.C Series
Instantaneous On-state Voltage
Fig. On-state Voltage Drop Characteristics
Transient Thermal Impedance thJ-hs (K/W)
Steady State Value thJ-hs 0.17 (Single Side Cooled)
thJ-hs 0.08 (Double Side Cooled) Operation)
0.01
ST230C.C Series
.001 0.001
0.01
Square Wave Pulse Duration
Fig. Thermal Impedance ZthJ-hs Characteristics
Instantaneous Gate Voltage
Rectangular gate pulse Recommended load line rated di/dt 20V, 10ohms; tr<=1 Recommended load line <=30% rated di/dt 10V, 10ohms tr<=1
10W, 20W, 40W, 60W,
0.66ms
Tj=-40 Tj=25
Tj=125
0.001 0.01
Device: ST230C.C Series
Frequency Limited PG(AV)
Instantaneous Gate Current
Fig. Gate Characteristics
www.irf.com
ST230C.C Series
Data specifications subject change without notice. This product been designed qualified Industrial Level. Qualification Standards found IR's site.
WORLD HEADQUARTERS: Kansas St., Segundo, California 90245, Tel: (310) 252-7105 Fax: (310) 252-7309 Visit www.irf.com sales contact information.
www.irf.com
Other recent searches
SPP08N50C3 - SPP08N50C3 SPP08N50C3 Datasheet
SPI08N50C3 - SPI08N50C3 SPI08N50C3 Datasheet
SPA08N50C3 - SPA08N50C3 SPA08N50C3 Datasheet
RLB9012 - RLB9012 RLB9012 Datasheet
MPX4100 - MPX4100 MPX4100 Datasheet
LR92984 - LR92984 LR92984 Datasheet
HVR600P - HVR600P HVR600P Datasheet
CM2596S - CM2596S CM2596S Datasheet
AN1374 - AN1374 AN1374 Datasheet
Privacy Policy | Disclaimer
© 2012 Datasheet Archive
