Absolute Encoder Multiturn with SSI-Interface Features Resolution

The Datasheet Archive - 100 Million Datasheets from 7500 Manufacturers.

Absolute Encoder Multiturn with SSI-Interface Features Resolution

Datasheet Thumbnail

Top Searches for this datasheet

GM400, GM401
Absolute Encoder Multiturn with SSI-Interface
Features Resolution bit, 8192 steps/revolution 4096 revolutions Gray binary code Synchronous Serial Interface Self-diagnostic High code switching speed Electronic zero point setting
GM400 clamping flange
Description diagnostic functions following monitored during operation: check code steadiness whether admissible signal frequency exceeded failure, aging whether receiver failed code disc, broken glass supply voltage electronically controlled gearbox
Electrical data GM401 synchro flange Supply voltage Current consumption pulse frequency Mono-flop time Pulse space Code switching speed sampling Deviation sampling measuring step Electric connector 10.30 with reverse voltage protection Max. (w/o load) 62.5 Min. 0.025 degree 0.05 degree electric connector must plugged removed whilst under voltage.
GmbH 3360 D-78022 Villingen-Schwenningen Phone (0)7720 942-0 (0)7720 942-999 www.ivo.de e-mail: info@ivo.de Printed Germany 07.01 GmbH 170.02.121/4
GM400, GM401
Order designation Order Flange Shaft GM400 Clamping flange Clamping flange GM401 Synchro flange Synchro flange Voltage Signals 10.30 Gray 10.30 Binary 10.30 Gray 10.30 Gray Parity 10.30 Gray Connection C-plug with pins, axial C-plug with pins, radial core cable axial core cable radial Assignment
Ambient conditions Ambient temperature Storage temperature Protection Shaft seal Shaft with seal Relative humidity Endurance Vibration Shock Interference immunity Emmited interference -20.+60 -20.+70 Max. non-condensing Section m/s2/ 16-2000 Section 2000 m/s2 50082-2 61000-4 Severity grade 50081-2
Mechanical data value mechanical electrical Anlauf-Drehmoment seal (IP54) with seal (IP65) Shaft loading axial radial Inertia torque Material Housing Flange Weight
Max. 10,000 Max. 6,000 0.010 0.015 10-6 kgm2 Steel Aluminium Approximately
GM400. GM401.
clamping flange synchro flange
Inputs Control signals UP/DOWN zero High level level Connection: UP/DOWN input with kohms against except zero-setting input with kohms against GND. pulse Optocoupler inputs electrical isolation
Outputs data RS485 Diagnostic outputs Push-pull output, short-circuit-protected High level -3.5 level
(for (for
GM400, GM401
Contact descriptions Supply voltage encoder Housing contact encoger. specific voltage Positive pulse input. Pulse produces current loop together with Pulse current approximately direction input Pulse generates logical positive logic. Positive serial data output differential line driver. High level output logically corresponds positive logic. Reset input setting zero point anywhere within entire resolution. zero setting triggered High pulse (pulse duration imperatively after sense direction been chosen (UP/DOWN). Assign maximum interference immunity after zero setting. Negative serial data output differential line driver. High level output logically corresponds positive logic. Negative pulse input. Pulse produces current loop together with Pulse current direction input Pulse generates logical positive logic.
assignment Cable color brown black blue beige green yellow violett brown/yellow pink black/yellow Assignment Pulse Data ZERO Data Pulse DATAVALID UP/DOWN DATAVALID
Pulse
Data
ZERO
Recommendation: Please leads twisted pairs extension cord.
Data
Pulse
Diagnostic output DATAVALID Jumps within data word, defective DATAVALID photoreceiver, displayed DV-output. addition, supply multiturn sensor unit monitored, output voltage falls below fixed limit. Both outputs Low-active, i.e. switched through case error. UP/DOWN Input counting down. open-circuited, High. UP/DOWN High means increasing output data shaft rotates clockwise when looking flange. UP/DOWN means increasing values shaft rotates counter-clockwise when looking flange. assigned
Accessories Order 119.015 119.017 119.018 121.C01 121.C02 121.C03 Mounting bell synchro flange Angular fixing clamping flange Eccentric fixing screws Spring-washer coupling Bore holes Spring-washer coupling Bore holes Spring-washer coupling Bore holes Extension cord with connector side Connector without cable Connector with cable Connector with cable Connector with cable Suitable positioning device
130.001 130.003 130.005 130.007 NA214
GM400, GM401
Dimensions cutout size GM400 clamping flange
deep 120°
Square flange 2.5"
8.76 (0.34") (0.375") (1.25")
10h6
10h6
Nose
36f8 ±0.1
11.5
Please order connector separately
4(0.16")
Dimensions 63.5 63.5 (2.5") Bore fixing (0.21") (Order upon request)
10h6
Nose
Please order connector separately
GM401 synchro flange
deep 120°
11.5
±0.1 50h7
Please order connector separately
Nose
Please order connector separately
Subject modification technic design. Errors omissions excepted.
Nose
10h6

Absolute Encoder Multiturn with SSI-Interface Features Resolution

Top Searches for this datasheet

Other recent searches