v02.0508 MMIC BUFFER AMPLIFIER, noise MMIC w/Buffer Amplifie
|
|
|
Top Searches for this datasheet
HMC505LP4 505LP4E
v02.0508
MMIC BUFFER AMPLIFIER,
noise MMIC w/Buffer Amplifier for: VSAT Microwave Radio Test Equipment Industrial Controls Military
Features
Pout: +11dBm Phase Noise: -106 dBc/Hz @100 External Resonator Needed Single Supply: Leadless Package, 16mm2
Functional Diagram
General Description
HMC505LP4 HMC505LP4E GaAs InGaP Heterojunction Bipolar Transistor (HBT) MMIC VCOs with integrated resonators, negative resistance devices, varactor diodes, buffer amplifiers. Covering GHz, VCO's phase noise performance excellent over temperature, shock vibration oscillator's monolithic structure. Power output typical from single supply voltage controlled oscillator packaged leadless surface mount package.
VCOS PLOs
Electrical Specifi cations, +25°
Parameter Frequency Range Power Output Phase Noise Offset, Vtune= Output Tune Voltage (Vtune) Supply Current (Icc) (Vcc +3.0V) Tune Port Leakage Current Output Return Loss Harmonics Pulling (into 2.0:1 VSWR) Pushing Vtune= Frequency Drift Rate Min. Typ. -106 Max. Units dBc/Hz MHz/V MHz/°C
price, delivery, place orders, please contact Hittite Microwave Corporation: Alpha Road, Chelmsford, 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line www.hittite.com
HMC505LP4 505LP4E
v02.0508
MMIC BUFFER AMPLIFIER,
Frequency Tuning Voltage, 25°C
FREQUENCY (GHz) TUNING VOLTAGE (VOLTS)
2.75V 3.0V 3.25V
Frequency Tuning Voltage, Vcc=
FREQUENCY (GHz) TUNING VOLTAGE (VOLTS)
+25C +85C -40C
VCOS PLOs
Sensitivity Tuning Voltage, Vcc=
SENSITIVITY (MHz/VOLT)
Output Power Tuning Voltage, Vcc=
OUTPUT POWER (dBm)
+25C +85C -40C
+25C +85C -40C
TUNING VOLTAGE (VOLTS)
TUNING VOLTAGE (VOLTS)
Phase Noise Tuning Voltage
PHASE NOISE (dBc/Hz)
10kHz offset 100kHz offset
Typical Phase Noise Vtune=
PHASE NOISE (dBc/Hz) -100 -120 -140 -160
+25C +85C -40C
-105 -115 -125 TUNING VOLTAGE (VOLTS)
OFFSET FREQUENCY (Hz)
price, delivery, place orders, please contact Hittite Microwave Corporation: Alpha Road, Chelmsford, 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line www.hittite.com
HMC505LP4 505LP4E
v02.0508
MMIC BUFFER AMPLIFIER,
Absolute Maximum Ratings
Vtune Channel Temperature Continuous Pdiss 85°C) (derate 6.31 mW/°C above 85°C) Thermal Resistance (RTH) (junction package base) Storage Temperature Operating Temperature Sensitivity (HBM) +3.5 +11V °C/W +150 Class
Typical Supply Current
2.75 3.25 (mA)
Note: will operate over full voltage range shown above.
ELECTROSTATIC SENSITIVE DEVICE OBSERVE HANDLING PRECAUTIONS
VCOS PLOs
Outline Drawing
NOTES: LEADFRAME MATERIAL: COPPER ALLOY DIMENSIONS INCHES [MILLIMETERS] LEAD SPACING TOLERANCE NON-CUMULATIVE. BURR LENGTH SHALL 0.15mm MAXIMUM. BURR HEIGHT SHALL 0.05mm MAXIMUM. PACKAGE WARP SHALL EXCEED 0.05mm. GROUND LEADS GROUND PADDLE MUST SOLDERED GROUND. REFER HITTITE APPLICATION SUGGESTED LAND PATTERN.
Package Information
Part Number HMC505LP4 HMC505LP4E Package Body Material Stress Injection Molded Plastic RoHS-compliant Stress Injection Molded Plastic Lead Finish Sn/Pb Solder 100% matte Rating MSL1 MSL1
Package Marking H505 XXXX H505 XXXX
peak reflow temperature peak reflow temperature 4-Digit number XXXX
price, delivery, place orders, please contact Hittite Microwave Corporation: Alpha Road, Chelmsford, 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line www.hittite.com
HMC505LP4 505LP4E
v02.0508
MMIC BUFFER AMPLIFIER,
Descriptions
Number Function Description Connection. These pins connected ground. Performance will affected. Interface Schematic
This must connected ground.
RFOUT
output coupled)
Supply Voltage Vcc=
VCOS PLOs
VTUNE
Control Voltage Input. Modulation port bandwidth dependent drive source impedance.
Package bottom exposed metal paddle that must grounded.
price, delivery, place orders, please contact Hittite Microwave Corporation: Alpha Road, Chelmsford, 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line www.hittite.com
HMC505LP4 505LP4E
v02.0508
MMIC BUFFER AMPLIFIER,
Evaluation
VCOS PLOs
List Materials Evaluation 105706
Item Description Mount Connector Tantalum Capacitor 10,000 Capacitor, 0603 Pkg. HMC505LP4 HMC505LP4E 105667 Eval Board
Reference this number when ordering complete evaluation Circuit Board Material: Rogers 4350
circuit board used final application should circuit design techniques. Signal lines should have impedance while package ground leads exposed paddle should connected directly ground plane similar that shown. sufficient number holes should used connect bottom ground planes. evaluation circuit board shown available from Hittite upon request.
price, delivery, place orders, please contact Hittite Microwave Corporation: Alpha Road, Chelmsford, 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line www.hittite.com
HMC505LP4 505LP4E
v02.0508
MMIC BUFFER AMPLIFIER,
Notes:
VCOS PLOs
price, delivery, place orders, please contact Hittite Microwave Corporation: Alpha Road, Chelmsford, 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line www.hittite.com
Other recent searches
SD5000C - SD5000C SD5000C Datasheet
LCM24064ZK - LCM24064ZK LCM24064ZK Datasheet
DTA123JUB - DTA123JUB DTA123JUB Datasheet
BAT74 - BAT74 BAT74 Datasheet
AB206 - AB206 AB206 Datasheet
Privacy Policy | Disclaimer
© 2012 Datasheet Archive
