1.2'' MATRIX DISPLAY 1.2inch (30.48 height power consumption RoHS
|
|
|
Top Searches for this datasheet
American Opto Plus C/A3570Y
1.2'' MATRIX DISPLAY
1.2inch (30.48 height power consumption RoHS Compliance Case mold type
Notes: dimensions millimeters (inches) Tolerance 0.25mm (0.01") unless otherwise specified
Feb. 2005 Rev.
American Opto Plus C/A3570Y
1.2'' MATRIX DISPLAY
1.2inch (30.48 height power consumption RoHS Compliance Case mold type
Internal Circuit Diagram
A3570 SERIES DIAGRAM (COLUMN ANODE)
C3570 SERIES DIAGRAM (COLUMN CATHODE)
Feb. 2005 Rev.
American Opto Plus C/A3570Y
1.2'' MATRIX DISPLAY
1.2inch (30.48 height power consumption RoHS Compliance Case mold type
DEVICE SELECTION GUIDE
Part Number 3570Y Material AlGaAs Chip Emitted Color Yellow Face Segment Gray White
ABSOLUTE MAXIMUM RATINGS
Parameter
Power Dissipation segment Peak Current segment (1/10 Duty Cycle @1KHz Continuous Forward Current segment Reverse Voltage Operating Temperature Range Storage Temperature Range
(Ta=25°C)
Symbol
TOPR TSTG
Rating
-40~+85 -40~+85
Unit
Solder temperature from body seconds 260°C
OPTICAL-ELECTRICAL CHARACTERISTICS
Parameter
Ave. Luminous Intensity Forward Voltage/segment Reverse Current/segment Spectrum Line Half-Width Dominant Wavelength Peak Wavelength
Symbol Test Condition
10mA 10mA 10mA 10mA 10mA
1200
4700 1.90
Unit
Feb. 2005 Rev.
American Opto Plus C/A3570Y
1.2'' MATRIX DISPLAY
1.2inch (30.48 height power consumption RoHS Compliance Case mold type
TYPICAL ELECTRO-OPTICAL CHARACTERISTIC CURVES: YELLOW
American Opto Plus C/A3570Y
1.2'' MATRIX DISPLAY
1.2inch (30.48 height power consumption RoHS Compliance Case mold type
WAVE SOLDERING
American Opto Plus C/A3570Y
1.2'' MATRIX DISPLAY
1.2inch (30.48 height power consumption RoHS Compliance Case mold type
LAMP HANDLING APPLICATION PRECAUTIONS STORAGE
recommended store products following conditions: Humidity: Temperature: 40°C (41°F 105°F) Shelf life sealed bag: month 40°C
FORMING
forming lead must done before solding, during after soldering Avoid applying stress resin order prevent epoxy fracture break bonding wire. While forming, please equivalent hold bend pin. from base resin minimum distance place bending lead Avoid bending lead same point twice more
SOLDERING
stress applied lead pins when they heated, otherwise disconnection occur. When mounted into P.C. board, pitch spacing should aligned carefully avoid causing stress lead wires. Mounting direction (electrode direction) Display should perpendicular direction curve After soldering, don't bend
CLEANING
Avoid using unspecified chemical solvent clean LED. example, Trichoroethylene, Chlorosen, Acetone, Diflon S3MC. cleaning method only taken under normal temperature minute less required Special attention should taken when using chemicals claning because some chemicals damage surface epoxy.
Other recent searches
TBR12 - TBR12 TBR12 Datasheet
IDT82V2042E - IDT82V2042E IDT82V2042E Datasheet
SC-70 - SC-70 SC-70 Datasheet
MN102H00 - MN102H00 MN102H00 Datasheet
LM317K - LM317K LM317K Datasheet
IRFB52N15D - IRFB52N15D IRFB52N15D Datasheet
IRFS52N15D - IRFS52N15D IRFS52N15D Datasheet
FDB8860 - FDB8860 FDB8860 Datasheet
BS9493 - BS9493 BS9493 Datasheet
2SD2150 - 2SD2150 2SD2150 Datasheet
Privacy Policy | Disclaimer
© 2012 Datasheet Archive
