2.3'' MATRIX DISPLAY inch (58.4 height power consumption RoHS Com
|
|
|
Top Searches for this datasheet
American Opto Plus C/A5581-1Y
2.3'' MATRIX DISPLAY
inch (58.4 height power consumption RoHS Compliance Case mold type
Notes: dimensions millimeters (inches) Tolerance 0.25mm (0.01") unless otherwise specified
Feb. 2005 Rev.
American Opto Plus C/A5581-1Y
2.3'' MATRIX DISPLAY
inch (58.4 height power consumption RoHS Compliance Case mold type
Internal Circuit Diagram
A5581-1 SERIES DIAGRAM (COLUMN ANODE)
C5581-1 SERIES DIAGRAM (COLUMN CATHODE)
Feb. 2005 Rev.
American Opto Plus C/A5581-1Y
2.3'' MATRIX DISPLAY
inch (58.4 height power consumption RoHS Compliance Case mold type
DEVICE SELECTION GUIDE
Part Number 5581-1Y Material AlGaAs Chip Emitted Color Yellow Face Segment Gray White
ABSOLUTE MAXIMUM RATINGS
Parameter
Power Dissipation segment Peak Current segment (1/10 Duty Cycle @1KHz Continuous Forward Current segment Reverse Voltage Operating Temperature Range Storage Temperature Range
(Ta=25°C)
Symbol
TOPR TSTG
Rating
-40~+85 -40~+85
Unit
Solder temperature from body seconds 260°C
OPTICAL-ELECTRICAL CHARACTERISTICS
Parameter
Ave. Luminous Intensity Forward Voltage/segment Reverse Current/segment Spectrum Line Half-Width Dominant Wavelength Peak Wavelength
Symbol Test Condition
10mA 10mA 10mA 10mA 10mA
1900
6400 1.90
Unit
Feb. 2005 Rev.
American Opto Plus C/A5581-1Y
2.3'' MATRIX DISPLAY
inch (58.4 height power consumption RoHS Compliance Case mold type
TYPICAL ELECTRO-OPTICAL CHARACTERISTIC CURVES: YELLOW
American Opto Plus C/A5581-1Y
2.3'' MATRIX DISPLAY
inch (58.4 height power consumption RoHS Compliance Case mold type
WAVE SOLDERING
American Opto Plus C/A5581-1Y
2.3'' MATRIX DISPLAY
inch (58.4 height power consumption RoHS Compliance Case mold type
LAMP HANDLING APPLICATION PRECAUTIONS STORAGE
recommended store products following conditions: Humidity: Temperature: 40°C (41°F 105°F) Shelf life sealed bag: month 40°C
FORMING
forming lead must done before solding, during after soldering Avoid applying stress resin order prevent epoxy fracture break bonding wire. While forming, please equivalent hold bend pin. from base resin minimum distance place bending lead Avoid bending lead same point twice more
SOLDERING
stress applied lead pins when they heated, otherwise disconnection occur. When mounted into P.C. board, pitch spacing should aligned carefully avoid causing stress lead wires. Mounting direction (electrode direction) Display should perpendicular direction curve After soldering, don't bend
CLEANING
Avoid using unspecified chemical solvent clean LED. example, Trichoroethylene, Chlorosen, Acetone, Diflon S3MC. cleaning method only taken under normal temperature minute less required Special attention should taken when using chemicals claning because some chemicals damage surface epoxy.
Other recent searches
TC74ACT161 - TC74ACT161 TC74ACT161 Datasheet
TC74ACT161P - TC74ACT161P TC74ACT161P Datasheet
TC74ACT161F - TC74ACT161F TC74ACT161F Datasheet
TC74ACT161FN - TC74ACT161FN TC74ACT161FN Datasheet
TC74ACT163P - TC74ACT163P TC74ACT163P Datasheet
TC74ACT163F - TC74ACT163F TC74ACT163F Datasheet
TC74ACT163FN - TC74ACT163FN TC74ACT163FN Datasheet
TC74ACT161P - TC74ACT161P TC74ACT161P Datasheet
TC74ACT163P - TC74ACT163P TC74ACT163P Datasheet
NLX2G04 - NLX2G04 NLX2G04 Datasheet
ENN7137 - ENN7137 ENN7137 Datasheet
CY2305 - CY2305 CY2305 Datasheet
CY2309 - CY2309 CY2309 Datasheet
CY2308 - CY2308 CY2308 Datasheet
CY2309 - CY2309 CY2309 Datasheet
AN2283 - AN2283 AN2283 Datasheet
8155630000 - 8155630000 8155630000 Datasheet
2SA1641 - 2SA1641 2SA1641 Datasheet
Privacy Policy | Disclaimer
© 2012 Datasheet Archive
