2.3'' MATRIX DISPLAY inch (58.4 height power consumption RoHS Com
|
|
|
Top Searches for this datasheet
American Opto Plus C/A5581SR
2.3'' MATRIX DISPLAY
inch (58.4 height power consumption RoHS Compliance Case mold type
Notes: dimensions millimeters (inches) Tolerance 0.25mm (0.01") unless otherwise specified
Feb. 2005 Rev.
American Opto Plus C/A5581SR
2.3'' MATRIX DISPLAY
inch (58.4 height power consumption RoHS Compliance Case mold type
Internal Circuit Diagram
A5581 SERIES DIAGRAM (COLUMN ANODE)
C5581 SERIES DIAGRAM (COLUMN CATHODE)
Feb. 2005 Rev.
American Opto Plus C/A5581SR
2.3'' MATRIX DISPLAY
inch (58.4 height power consumption RoHS Compliance Case mold type
DEVICE SELECTION GUIDE
Part Number 5581SR Material AlGaAs Chip Emitted Color Super Face Segment Gray White
ABSOLUTE MAXIMUM RATINGS
Parameter
Power Dissipation segment Peak Current segment (1/10 Duty Cycle @1KHz Continuous Forward Current segment Reverse Voltage Operating Temperature Range Storage Temperature Range
(Ta=25°C)
Symbol
TOPR TSTG
Rating
-40~+85 -40~+85
Unit
Solder temperature from body seconds 260°C
OPTICAL-ELECTRICAL CHARACTERISTICS
Parameter
Ave. Luminous Intensity Forward Voltage/segment Reverse Current/segment Spectrum Line Half-Width Dominant Wavelength Peak Wavelength
Symbol Test Condition
20mA 10mA 10mA 10mA 10mA
8000
27000 1.75
Unit
Feb. 2005 Rev.
American Opto Plus C/A5581SR
2.3'' MATRIX DISPLAY
inch (58.4 height power consumption RoHS Compliance Case mold type
TYPICAL ELECTRO-OPTICAL CHARACTERISTIC CURVES: SUPER (SR)
American Opto Plus C/A5581SR
2.3'' MATRIX DISPLAY
inch (58.4 height power consumption RoHS Compliance Case mold type
WAVE SOLDERING
American Opto Plus C/A5581SR
2.3'' MATRIX DISPLAY
inch (58.4 height power consumption RoHS Compliance Case mold type
LAMP HANDLING APPLICATION PRECAUTIONS STORAGE
recommended store products following conditions: Humidity: Temperature: 40°C (41°F 105°F) Shelf life sealed bag: month 40°C
FORMING
forming lead must done before solding, during after soldering Avoid applying stress resin order prevent epoxy fracture break bonding wire. While forming, please equivalent hold bend pin. from base resin minimum distance place bending lead Avoid bending lead same point twice more
SOLDERING
stress applied lead pins when they heated, otherwise disconnection occur. When mounted into P.C. board, pitch spacing should aligned carefully avoid causing stress lead wires. Mounting direction (electrode direction) Display should perpendicular direction curve After soldering, don't bend
CLEANING
Avoid using unspecified chemical solvent clean LED. example, Trichoroethylene, Chlorosen, Acetone, Diflon S3MC. cleaning method only taken under normal temperature minute less required Special attention should taken when using chemicals claning because some chemicals damage surface epoxy.
Other recent searches
ZRO2405A1LF - ZRO2405A1LF ZRO2405A1LF Datasheet
SCHS135F - SCHS135F SCHS135F Datasheet
SBR20A40CT - SBR20A40CT SBR20A40CT Datasheet
SBR20A40CTFP - SBR20A40CTFP SBR20A40CTFP Datasheet
PT6302 - PT6302 PT6302 Datasheet
HD6433694 - HD6433694 HD6433694 Datasheet
HD6433693 - HD6433693 HD6433693 Datasheet
HD6433692 - HD6433692 HD6433692 Datasheet
HD6433691 - HD6433691 HD6433691 Datasheet
HD6433690 - HD6433690 HD6433690 Datasheet
HD6483694G - HD6483694G HD6483694G Datasheet
HD6433694G - HD6433694G HD6433694G Datasheet
HD6433693G - HD6433693G HD6433693G Datasheet
HD6433692G - HD6433692G HD6433692G Datasheet
HD6433691G - HD6433691G HD6433691G Datasheet
HD6433690G - HD6433690G HD6433690G Datasheet
FR301G - FR301G FR301G Datasheet
FR307G - FR307G FR307G Datasheet
BZX84B - BZX84B BZX84B Datasheet
ACT174 - ACT174 ACT174 Datasheet
Privacy Policy | Disclaimer
© 2012 Datasheet Archive
