3-State Version 'HC153 Wide Operating Voltage Range High-Current Inver
|
|
|
Top Searches for this datasheet
SN54HC253, SN74HC253 DUAL 4-LINE 1-LINE DATA SELECTORS/MULTIPLEXERS WITH 3-STATE OUTPUTS
3-State Version 'HC153 Wide Operating Voltage Range High-Current Inverting Outputs Drive LSTTL Loads Power Consumption, 80-µA Typical ±6-mA Output Drive Input Current Permit Multiplexing From Lines Line Perform Parallel-to-Serial Conversion
SN54HC253 PACKAGE SN74HC253 PACKAGE (TOP VIEW)
description/ordering information
Each these data selectors/multiplexers contains inverters drivers supply full binary decoding data selection AND-OR gates. Separate output-control inputs provided each 4-line sections. 3-state outputs interface with drive data lines bus-organized systems. With common outputs disabled high-impedance state), impedance single enabled output drives line high logic level. Each output output-enable (OE) input. outputs disabled when their respective high. ORDERING INFORMATION
PDIP -40°C 85°C SOIC SSOP CDIP -55°C 125°C LCCC PACKAGE Tube Tube Tape reel Tape reel Tape reel Tube Tube Tube
SN54HC253 PACKAGE (TOP VIEW)
internal connection
ORDERABLE PART NUMBER SN74HC253N SN74HC253D SN74HC253DR SN74HC253NSR SN74HC253DBR SNJ54HC253J SNJ54HC253W SNJ54HC253FK
SNJ54HC253FK Package drawings, standard packing quantities, thermal data, symbolization, design guidelines available www.ti.com/sc/package.
Please aware that important notice concerning availability, standard warranty, critical applications Texas Instruments semiconductor products disclaimers thereto appears this data sheet.
Copyright 2003, Texas Instruments Incorporated
products compliant MIL-PRF-38535, parameters tested unless otherwise noted. other products, production processing does necessarily include testing parameters.
PRODUCTION DATA information current publication date. Products conform specifications terms Texas Instruments standard warranty. Production processing does necessarily include testing parameters.
POST OFFICE 655303
DALLAS, TEXAS 75265
TOP-SIDE MARKING SN74HC253N HC253 HC253 HC253 SNJ54HC253J SNJ54HC253W
SN54HC253, SN74HC253 DUAL 4-LINE 1-LINE DATA SELECTORS/MULTIPLEXERS WITH 3-STATE OUTPUTS
FUNCTION TABLE INPUTS SELECT DATA OUTPUT
Select inputs common both sections.
POST OFFICE 655303
DALLAS, TEXAS 75265
SN54HC253, SN74HC253 DUAL 4-LINE 1-LINE DATA SELECTORS/MULTIPLEXERS WITH 3-STATE OUTPUTS
logic diagram (positive logic)
numbers shown packages.
POST OFFICE 655303
DALLAS, TEXAS 75265
SN54HC253, SN74HC253 DUAL 4-LINE 1-LINE DATA SELECTORS/MULTIPLEXERS WITH 3-STATE OUTPUTS
absolute maximum ratings over operating free-air temperature range (unless otherwise noted)
Supply voltage range, -0.5 Input clamp current, VCC) (see Note Output clamp current, VCC) (see Note Continuous output current, VCC) Continuous current through Package thermal impedance, (see Note package 73°C/W package 82°C/W package 67°C/W package 64°C/W Storage temperature range, Tstg -65°C 150°C
Stresses beyond those listed under "absolute maximum ratings" cause permanent damage device. These stress ratings only, functional operation device these other conditions beyond those indicated under "recommended operating conditions" implied. Exposure absolute-maximum-rated conditions extended periods affect device reliability. NOTES: input output voltage ratings exceeded input output current ratings observed. package thermal impedance calculated accordance with JESD 51-7.
recommended operating conditions (see Note
SN54HC253 Supply voltage High-level input voltage Low-level input voltage Input voltage Output voltage Input transition rise/fall time 3.15 1.35 1000 SN74HC253 3.15 1.35 1000 UNIT
Operating free-air temperature NOTE unused inputs device must held ensure proper device operation. Refer application report, Implications Slow Floating CMOS Inputs, literature number SCBA004.
POST OFFICE 655303
DALLAS, TEXAS 75265
SN54HC253, SN74HC253 DUAL 4-LINE 1-LINE DATA SELECTORS/MULTIPLEXERS WITH 3-STATE OUTPUTS
electrical characteristics over recommended operating free-air temperature range (unless otherwise noted)
PARAMETER TEST CONDITIONS -7.8 3.98 5.48 25°C 1.998 4.499 5.999 0.002 0.001 0.001 0.17 0.15 ±0.1 ±0.01 0.26 0.26 ±100 ±0.5 SN54HC253 ±1000 SN74HC253 3.84 5.34 0.33 0.33 ±1000 UNIT
switching characteristics over recommended operating free-air temperature range, (unless otherwise noted) (see Figure
PARAMETER FROM (INPUT) (OUTPUT) Data (Any tdis 25°C SN54HC253 SN74HC253 UNIT
POST OFFICE 655303
DALLAS, TEXAS 75265
SN54HC253, SN74HC253 DUAL 4-LINE 1-LINE DATA SELECTORS/MULTIPLEXERS WITH 3-STATE OUTPUTS
switching characteristics over recommended operating free-air temperature range, (unless otherwise noted) (see Figure
PARAMETER FROM (INPUT) (OUTPUT) Data (Any 25°C SN54HC253 SN74HC253 UNIT
operating characteristics, 25°C
PARAMETER Power dissipation capacitance multiplexer TEST CONDITIONS load UNIT
POST OFFICE 655303
DALLAS, TEXAS 75265
SN54HC253, SN74HC253 DUAL 4-LINE 1-LINE DATA SELECTORS/MULTIPLEXERS WITH 3-STATE OUTPUTS
PARAMETER MEASUREMENT INFORMATION
PARAMETER Test Point tPZH tPZL tPHZ tPLZ Open Closed Open Closed Open Closed Open Closed Open Open
From Output Under Test (see Note
tdis
LOAD CIRCUIT Input tPLH In-Phase Output tPHL Out-of-Phase Output tPLH tPHL
Output Control (Low-Level Enabling) tPZL Output Waveform (See Note tPZH
tPLZ tPHZ
VOLTAGE WAVEFORMS PROPAGATION DELAY OUTPUT TRANSITION TIMES
Input
Output Waveform (See Note
VOLTAGE WAVEFORM INPUT RISE FALL TIMES
VOLTAGE WAVEFORMS ENABLE DISABLE TIMES 3-STATE OUTPUTS
NOTES: includes probe test-fixture capacitance. Waveform output with internal conditions such that output except when disabled output control. Waveform output with internal conditions such that output high except when disabled output control. Phase relationships between waveforms were chosen arbitrarily. input pulses supplied generators having following characteristics: MHz, outputs measured time with input transition measurement. tPLZ tPHZ same tdis. tPZL tPZH same ten. tPLH tPHL same tpd.
Figure Load Circuit Voltage Waveforms
POST OFFICE 655303
DALLAS, TEXAS 75265
MECHANICAL DATA
MLCC006B OCTOBER 1996
(S-CQCC-N**)
TERMINAL SHOWN
LEADLESS CERAMIC CHIP CARRIER
TERMINALS
0.342 (8,69) 0.442 (11,23) 0.640 (16,26) 0.739 (18,78) 0.938 (23,83) 1.141 (28,99) 0.358 (9,09) 0.458 (11,63) 0.660 (16,76) 0.761 (19,32) 0.962 (24,43) 1.165 (29,59) 0.307 (7,80) 0.406 (10,31) 0.495 (12,58) 0.495 (12,58) 0.850 (21,6) 1.047 (26,6)
0.358 (9,09) 0.458 (11,63) 0.560 (14,22) 0.560 (14,22) 0.858 (21,8) 1.063 (27,0)
0.080 (2,03) 0.064 (1,63) 0.020 (0,51) 0.010 (0,25)
0.020 (0,51) 0.010 (0,25)
0.055 (1,40) 0.045 (1,14)
0.045 (1,14) 0.035 (0,89)
0.028 (0,71) 0.022 (0,54) 0.050 (1,27)
0.045 (1,14) 0.035 (0,89)
4040140 10/96 NOTES: linear dimensions inches (millimeters). This drawing subject change without notice. This package hermetically sealed with metal lid. terminals gold plated. Falls within JEDEC MS-004
POST OFFICE 655303
DALLAS, TEXAS 75265
MECHANICAL
MPDI002C JANUARY 1995 REVISED DECEMBER 20002
(R-PDIP-T**)
PINS SHOWN
PLASTIC DUAL-IN-LINE PACKAGE
PINS
0.775 (19,69) 0.745 (18,92)
0.775 (19,69) 0.745 (18,92)
0.920 (23,37) 0.850 (21,59)
1.060 (26,92) 0.940 (23,88)
0.260 (6,60) 0.240 (6,10)
MS-100 VARIATION
0.070 (1,78) 0.045 (1,14)
0.045 (1,14) 0.030 (0,76)
0.020 (0,51)
0.325 (8,26) 0.300 (7,62) 0.015 (0,38) 0.200 (5,08) Seating Plane 0.125 (3,18) 0.010 (0,25) Gauge Plane
0.100 (2,54) 0.021 (0,53) 0.015 (0,38) 0.010 (0,25)
0.430 (10,92)
14/18 ONLY vendor option
4040049/E 12/2002
NOTES: linear dimensions inches (millimeters). This drawing subject change without notice. Falls within JEDEC MS-001, except minimum body lrngth (Dim lead shoulder width vendor option, either half full width.
POST OFFICE 655303
DALLAS, TEXAS 75265
MECHANICAL DATA
MSOI002B JANUARY 1995 REVISED SEPTEMBER 2001
(R-PDSO-G**)
PINS SHOWN 0.050 (1,27) 0.020 (0,51) 0.014 (0,35) 0.010 (0,25)
PLASTIC SMALL-OUTLINE PACKAGE
0.244 (6,20) 0.228 (5,80) 0.157 (4,00) 0.150 (3,81)
0.008 (0,20)
Gage Plane 0.044 (1,12) 0.016 (0,40)
0.010 (0,25)
Seating Plane 0.069 (1,75) 0.010 (0,25) 0.004 (0,10) 0.004 (0,10)
PINS
0.197 (5,00) 0.189 (4,80)
0.344 (8,75) 0.337 (8,55)
0.394 (10,00) 0.386 (9,80)
4040047/E 09/01 NOTES: linear dimensions inches (millimeters). This drawing subject change without notice. Body dimensions include mold flash protrusion, exceed 0.006 (0,15). Falls within JEDEC MS-012
POST OFFICE 655303
DALLAS, TEXAS 75265
MECHANICAL DATA
MSSO002E JANUARY 1995 REVISED DECEMBER 2001
(R-PDSO-G**)
PINS SHOWN 0,65 0,38 0,22 0,15
PLASTIC SMALL-OUTLINE
0,25 0,09 5,60 5,00 8,20 7,40
Gage Plane 0,25 0,95 0,55
Seating Plane 2,00 0,05 0,10
PINS
6,50
6,50
7,50
8,50
10,50
10,50
12,90
5,90
5,90
6,90
7,90
9,90
9,90
12,30 4040065 12/01
NOTES:
linear dimensions millimeters. This drawing subject change without notice. Body dimensions include mold flash protrusion exceed 0,15. Falls within JEDEC MO-150
POST OFFICE 655303
DALLAS, TEXAS 75265
IMPORTANT NOTICE Texas Instruments Incorporated subsidiaries (TI) reserve right make corrections, modifications, enhancements, improvements, other changes products services time discontinue product service without notice. Customers should obtain latest relevant information before placing orders should verify that such information current complete. products sold subject TI's terms conditions sale supplied time order acknowledgment. warrants performance hardware products specifications applicable time sale accordance with TI's standard warranty. Testing other quality control techniques used extent deems necessary support this warranty. Except where mandated government requirements, testing parameters each product necessarily performed. assumes liability applications assistance customer product design. Customers responsible their products applications using components. minimize risks associated with customer products applications, customers should provide adequate design operating safeguards. does warrant represent that license, either express implied, granted under patent right, copyright, mask work right, other intellectual property right relating combination, machine, process which products services used. Information published regarding third-party products services does constitute license from such products services warranty endorsement thereof. such information require license from third party under patents other intellectual property third party, license from under patents other intellectual property Reproduction information data books data sheets permissible only reproduction without alteration accompanied associated warranties, conditions, limitations, notices. Reproduction this information with alteration unfair deceptive business practice. responsible liable such altered documentation. Resale products services with statements different from beyond parameters stated that product service voids express implied warranties associated product service unfair deceptive business practice. responsible liable such statements.
Mailing Address: Texas Instruments Post Office 655303 Dallas, Texas 75265
Copyright 2003, Texas Instruments Incorporated
Other recent searches
ZASM73E - ZASM73E ZASM73E Datasheet
TA1002A - TA1002A TA1002A Datasheet
SH7145F - SH7145F SH7145F Datasheet
LMV1022 - LMV1022 LMV1022 Datasheet
LMV1023 - LMV1023 LMV1023 Datasheet
LMV1022 - LMV1022 LMV1022 Datasheet
LMV1023 - LMV1023 LMV1023 Datasheet
LMV1024 - LMV1024 LMV1024 Datasheet
LMV1026 - LMV1026 LMV1026 Datasheet
IS61S6432 - IS61S6432 IS61S6432 Datasheet
BFY84DCSM - BFY84DCSM BFY84DCSM Datasheet
Privacy Policy | Disclaimer
© 2012 Datasheet Archive
