Servo mount style Shaft supported front rear precision ball bearings N

The Datasheet Archive - 100 Million Datasheets from 7500 Manufacturers.

Servo mount style Shaft supported front rear precision ball bearings N

Datasheet Thumbnail

Top Searches for this datasheet

Servo mount style Shaft supported front rear precision ball bearings Non-standard features specifications available Gangable cups
6574 Precision Potentiometer
Electrical Characteristics1
Standard Resistance Range.1 ohms Total Resistance Tolerance .±10 Independent Linearity .±0.25 Effective Electrical Angle .350 Voltage .0.1 maximum (0.2 ohms, ohms) Output Smoothness .0.1 Dielectric Withstanding Voltage (MIL-STD-202, Method 301) Level .1,000 minimum Power Rating (Voltage Limited Power Dissipation VAC, Whichever Less) watts +125 °C.0 watt Insulation Resistance (500 VDC).1,000 megohms minimum Resolution .Essentially infinite
Product Dimensions
6.35 MIN. (.250) 6.34 .000/- .007 DIA. (.2497+.0000/-.0003) (.015) CHAMFER 47.63 +.000/ .025 (1.875+.000/-.001)
51.0 (2.000) DIA.
Environmental Characteristics1
Operating Temperature Range .-65 +125 Storage Temperature Range +125 Temperature Coefficient Over Storage Temperature Range .±500 ppm/°C maximum Vibration Wiper Bounce .0.1 millisecond maximum Total Resistance Shift maximum Shock Wiper Bounce .0.1 millisecond maximum Load Life .1,000 hours, watts Total Resistance Shift .±10 maximum Rotational Life Load).25,000,000 shaft revolutions Total Resistance Shift .±10 maximum Moisture Resistance (MIL-STD-202, Method 103, Condition Total Resistance Shift .±10 maximum Rating
15.24 .787 (.600 .031)
2.36 (.093)
1.57 (.062) 2.03 MIN. (.080) 15.9 (5/8 1/32)
MAX.
Mechanical Characteristics1
Mechanical Angle .Continuous Torque (Starting Running) .0.53 N-cm (0.75 oz.-in.) maximum Shaft Runout.0.025 (0.001 in.) T.I.R. Shaft Play .0.08 (0.003 in.) T.I.R. Shaft Radial Play .0.08 (0.003 in.) T.I.R. Pilot Diameter Runout.0.025 (0.001 in.) T.I.R. Lateral Runout .0.08 (0.003 in.) T.I.R. Backlash .0.1 maximum Weight Terminals.Side exit turret terminals Soldering Condition .Recommended hand soldering using Sn95/Ag5 clean solder, 0.025 wire diameter. Maximum temperature (750 seconds. wash process used with clean flux. Marking .Manufacturer's name part number, resistance value tolerance, linearity tolerance, wiring diagram, date code. Ganging (Multiple Section Potentiometers) maximum Hardware hardware included
29.59 (1.165) MAX.
TOLERANCES: EXCEPT WHERE NOTED DECIMALS: .XXX (.02), (.005) FRACTIONS: ±1/64 DIMENSIONS: (IN.)
WIPER
CLOCKWISE
room ambient: nominal relative humidity nominal, except noted.
Recommended Part Numbers
Part Number* 6574S-1-102 6574S-1-502 6574S-1-103 Resistance 1,000 5,000 10,000
BOLDFACE LISTINGS STOCK READILY AVAILABLE THROUGH DISTRIBUTION. OTHER OPTIONS CONSULT FACTORY. REV. 04/03 Specifications subject change without notice.

Servo mount style Shaft supported front rear precision ball bearings N

Top Searches for this datasheet

Other recent searches