IN-VEHICLE HEALTH MONITORING PROBLEMS HEALTH MONITORING AIRCRAFT
|
|
|
Top Searches for this datasheet
AEROFLEX COLORADO SPRINGS MIXED-SIGNAL ASIC SOLUTIONS
IN-VEHICLE HEALTH MONITORING
PROBLEMS HEALTH MONITORING AIRCRAFT AUTOMOTIVE Wiring weight complexity. reliability. Limited performance Data rate. Noise susceptibility. System cost Design, material, support. Long design cycle time. Wireless node cost Supporting circuitry wireless protocol. Size Difficult miniaturize each node. Wireless asynchronous data acquisition. Network Interface Controller (inside
Example: actuators position sensors
SOLUTION AEROFLEX'S NIC/NDI NETWORK ASICS WITH INTELLIBUSPROTOCOL Single cable Daisy-chained twisted-pair wiring between nodes. High data rates 30Mbps. cost device count each node. Isochronous data acquisition Networkwide simultaneous sampling. 800-645-8862 Aeroflex's AX7000-NIC AX30NDI data sheets www.aeroflex.com/mixedsignal
What IntelliBusProtocol?
IntelliBus Boeing-developed serial databus communication standard designed network sensors, actuators, subsystems while providing simplicity necessary miniature smart sensors, latency needed flight controls, time determinism required data analysis, distance industrial control. IntelliBus permits integration signal conditioning, analog-to-digital conversion, digital interfacing into low-cost package that installed sensor, actuator, interface module, system. Aeroflex Colorado Springs (Aeroflex) licensed IntelliBus standard market products 2004. IntelliBus overhead that enables maximum data transmittal, accommodates both sensors actuators monitoring control, incorporates fault avoidance features. Additionally, IntelliBus accommodates high sensor count (over 500), allows synchronization between multiple busses, simultaneous sampling capability, isochronous transmission with jitter (+/- 500ps). IntelliBus time deterministic enables high data rates (30, Mbps) while maintaining cost-per-node. Aeroflex developed Network System product family consisting Network Interface Controller (NIC) Network Device Interface (NDI) address variety communication control network requirements Factory Floor Automation In-Vehicle Health Monitoring fields. Features include: standard functions services that locate, configure, operate wide range transducer devices mechanism acquire distribute data: Synchronously multiple sample rates Simultaneously with minimal acquisition jitter Minimal network latency without strict constraints communication peripheral device Support device (node) memory containing node information automatic peripheral configuration boot) Multi-cast connectivity large number peripheral devices mechanism node filter trap network data Low-overhead time-deterministic device-todevice data transfers Data buffering minimize network latency Low-cost, compliant physical layer: easymaintenance twisted-pair copper Capable Mbps data rate Scalable hardware, firmware software Physical Data Link layers (OSI layers 1-2) product features listed above, twisted pair copper wiring utilized with M-LVDS (Multipoint-LowVoltage Differential Signaling) data transceivers high-speed Mbps) signaling, RS-485 transceivers lower speed applications. Off-theshelf transceivers used. proprietary sampling schemes receiver, clock recovery re-syncing necessary physical layer (layer only signal level translation output tri-stating required. typical Aeroflex NIC/NDI network system consists controller multiple nodes. Half duplex data transmission occurs, where only controller addressed node actively transmitting data. More than node receiving data. (Full-duplex communication possible single controller-to-node system. Data Link layer (layer support provided hardware functions: Network Interface Controller (NIC) Network Device Interface (NDI). AX7000 Network Interface Controller (NIC) function master controller Aeroflex NIC/NDI network. Connecting directly physical layer transceiver, controls scheduling data communications network issuing commands devices network. Typically card host uses IntelliBus protocol opcodes which allow host modification access scheduler, well direct access network data. AX30 Network Device Interface (NDI) function miniaturized interface chip connecting peripheral devices onto Aeroflex NIC/NDI serial network. IntelliBus protocol allows each device support peripherals channels). These peripherals range from simple sensors indicators complex audio/visual components. With Mbps throughput physical bus, many chips supported single Aeroflex NIC/NDI network, with maximum addressable range channels bus. Presentation layer (OSI layer Included support serial data communications with peripherals SPI, ISC, UART ports. number ports (channels) available within specific determine count size device; thus, range device package sizes supports variety peripheral area constraints. Input output FIFO buffering provided within support difference data rates between peripherals highspeed Aeroflex NIC/NDI traffic rate. Application layer (OSI layer Included flexible support large variety signal processing signal conditioning devices, such Analog Digital Converters Digital Analog Converters Microcontrollers Digital (switches, indicator drive) Inter-node communication
Standard Products
AX7000-NIC Network Interface Controller (NIC)
Preliminary Datasheet- 2005
www.aeroflex.com/mixedsignal
FEATURES Supports IntelliBusProtocol v3.0 Dual IntelliBus Network Ports Full Half Duplex Support IntelliBus RS-485 Physical Layer Synchronous Data Rates 15.0 Mbps Asynchronous Data Rates 7.5, 15.0 Mbps 256K Word Schedule Memory Word Dynamic Schedule Register Space Word Deep Receiver FIFOs External IntelliBus Power Source APPLICATIONS Sensor Integration Factory Floor Automation In-Vehicle Healthy Monitoring Process Control Systems
GENERAL DESCRIPTION AX7000-NIC Network Interface Controller (NIC) third generation controller design specifically used controller based IntelliBus development system. card plugs directly into 66Mhz, 32-bit 3.3V V2.2 compliant slot Pentium compatible computer. card supports semi-independent IntelliBus serial channels, which operate asynchronous mode supporting IntelliBus Isochronous (IS) communications tier data rates to15Mbps. IntelliBus network channels implemented using IntelliBus RS-485 physical layer configured Half Full Duplex arrangement. card contains word deep FIFO each network receiver channels. This allows real time data collection using standard operating system. control data retrieval operations handled software through registers implemented interface. card supports custom microcode instruction that used control execution schedule. microcode loaded, software, into onboard schedule memory. card contains status lights real time indication state network. controls from Interface Card. AX7000-NIC manufactured Aeroflex Colorado Springs' 104,000-square foot ISO-9001 certified facility. Aeroflex Colorado Springs been producing high-reliability integrated circuits circuit card assemblies aerospace industry since 1980.
BENEFITS Network Interface Controller (AX7000-NIC) Capable running network schedule Provides gateway other higher networks Supports logical addresses sensors, actual tors, IICs Host processor directly talk control IntelliBus schedule Runs membership services functions Provides synchronous trigger time-base Contains network traffic FIFO buffer Multiple form factors available (PCI user specified)
Figure AX7000-NIC Network Interface Controller
ABSOLUTE MAXIMUM RATINGS1 PARAMETER Voltage 3.3V Voltage 5.0V External Power Input External Clock Input Operating Temperature Storage Temperature
Notes:
Stresses greater than those listed under absolute maximum specifications cause permanent damage device. This stress rating only, functional operation device these other conditions above those indicated operational sections this specification implied. Prolonged exposure absolute maximum rating conditions affect reliability.
RECOMMENDED OPERATING CONDITIONS PARAMETER Voltage 3.3V Voltage 5.0V Current 3.3V Current 5.0V LIMITS 3.0V 3.6V 4.7V 5.3V +70°C
LIMITS -0.5 -0.5 -0.5
Power Dissipation +70°C Operating Temperature -30°C +90°C
COLORADO Toll Free: 800-645-8862 Fax: 719-594-8468 MID-ATLANTIC Tel: 321-951-4164 Fax: 321-951-4254
INTERNATIONAL Tel: 805-778-9229 Fax: 805-778-1980 WEST COAST Tel: 949-362-2260 Fax: 949-362-2266
NORTHEAST Tel: 603-888-3975 Fax: 603-888-4585 CENTRAL Tel: 719-594-8017 Fax: 719-594-8468
www.aeroflex.com
info-ams@aeroflex.com
Aeroflex Colorado Springs, Inc., reserves right make changes products services herein time without notice. Consult Aeroflex authorized sales representative verify that information this data sheet current before using this product. Aeroflex does assume responsibility liability arising application product service described herein, except expressly agreed writing Aeroflex; does purchase, lease, product service from Aeroflex convey license under patent rights, copyrights, trademark rights, other intellectual rights Aeroflex third parties.
passion performance defined three attributes represented these three icons: solution-minded, performance-driven customer-focused
Mixed-Signal ASIC Products
AX30NDI-09/05/02 Network Interface Device (NDI) with IntelliBusProtocol
Preliminary Datasheet 2005 www.aeroflex.com/MixedSignal
FEATURES Network Device Interface (NDI) designed specifically for: Factory Floor Automation applications In-Vehicle Health Monitoring applications Compliant IntelliBus Standards Generation Protocol Full IntelliBus data rates 7.5, Mbps (pinselectable) Variety package sizes: channel variants Network connection through simple MLVDS RS-485 external transceiver device bootup memory supported words external serial flash Configurable internal generates multiple isochronous peripheral clocks 24.576 MHz)
Variety serial connections peripherals: SPI, I2S, UART 16-word output FIFO channel peripheral) Dual 16-word input FIFOs channel (from peripheral) Single-supply 3.3V device with tolerant Commercial Industrial temperature ranges INTRODUCTION AX30NDI devices Network Device Interfaces compliant Generation IntelliBus protocol. These devices allow efficient connection variety peripheral devices onto multi-point IntelliBus network. Peripheral devices include converters data acquisition, audio video DACs multimedia digital basic control sense applications.
IntelliBus Network XCVR
LVTTL
IntelliBus Interface
IntelliBus Data
Memory Interface
Command Decoder
Channel Interface
UART
External Serial Flash Boot Clock Generation,
Trig/ Sync Clks
Config/ Control Signals
Remote Input Clock
AX030NDI-05: Channel thru only AX030NDI-02: Channel thru only
Figure AX30NDI-09 Block Diagram
IntelliBus Interface Data rates 7.5Mbps, 15Mbps 30Mbps userselectable bit-rate select control inputs AX30NDI. simple MLVDS RS-485 external transceiver required layer. internal Command Decoder interprets network IntelliBus commands from Network Interface Controller, performs appropriate data transfer peripheral control. External Serial Flash Interface AX30NDI device contains bootup algorithm support unique unique self-configuration port. This bootup data stored external flash, downloaded power-up into internal serial interface. Electronic Data Sheet information also stored external flash available access IntelliBus Network Interface Controller after bootup procedure downloads data RAM. flash interface implemented standard interface. Peripheral Interface (Ports) number available ports device type defined Table three family members AX30NDI differ only number ports, thus affecting package size. Each port supports protocol. shown AX30NDI-09 Block Diagram, alternate serial protocols supported: I2C, UART. These alternate modes user selected tie-offs. Each port contains three FIFOs buffering data flow. 16-word Output FIFO stores network data before transferring peripheral when proper (optionally isochronous) IntelliBus command decoded.
16-word Input Buffer second 16-word Input FIFO provided allow isochronous data collection peripheral data rates, with previous-frame data output IntelliBus network IntelliBus data rates. Isochronous timedeterministic data transfers from each port supported Trigger Sync signals, decoded from IntelliBus network commands. internal AX30NDI provides peripheral clocking which locked Trigger signal. Three user-defined frequencies available channels, ranging from 24.576 MHz. Remote Inputs AX30NDI contains support inputs which read IntelliBus Network Interface Controller determine physical location each located bus. These signals discrete inputs tied externally Ground. Table AX03NDI Packaging
Part AX30NDI-02-Q72 AX30NDI-02-B72 AX30NDI-05-L120 AX30NDI-05-B121 AX30NDI-09-B169 Channel Package Type 72-pin 72-pin FBGA 120-pin LQFP 121-pin FBGA 169-pin FBGA Dimensions w(mm)
COLORADO Toll Free: 800-645-8862 Fax: 719-594-8468 MID-ATLANTIC Tel: 321-951-4164 Fax: 321-951-4254
INTERNATIONAL Tel: 805-778-9229 Fax: 805-778-1980 WEST COAST Tel: 949-362-2260 Fax: 949-362-2266
NORTHEAST Tel: 603-888-3975 Fax: 603-888-4585 CENTRAL Tel: 719-594-8017 Fax: 719-594-8468
www.aeroflex.com
info-ams@aeroflex.com
Aeroflex Colorado Springs, Inc., reserves right make changes products services herein time without notice. Consult Aeroflex authorized sales representative verify that information this data sheet current before using this product. Aeroflex does assume responsibility liability arising application product service described herein, except expressly agreed writing Aeroflex; does purchase, lease, product service from Aeroflex convey license under patent rights, copyrights, trademark rights, other intellectual rights Aeroflex third parties.
passion performance defined three attributes represented these three icons: solution-minded, performance-driven customer-focused
Mixed-Signal ASIC Products
AX30NDI-09/05/02 Network Interface Device (NDI) with IntelliBusProtocol Internal
Preliminary Datasheet 2005 www.aeroflex.com/MixedSignal
FEATURES Network Device Interface (NDI) designed specifically for: Factory Floor Automation applications In-Vehicle Health Monitoring applications Compliant IntelliBus Standards Generation Protocol Full IntelliBus data rates 7.5, Mbps (pinselectable) Variety package sizes: channel variants Internal (MLVDS transceiver) direct IntelliBus connection device bootup memory supported words external serial flash Configurable internal generates multiple isochronous peripheral clocks 24.576 MHz)
Variety serial connections peripherals: SPI, I2S, UART 16-word output FIFO channel peripheral) Dual 16-word input FIFOs channel (from peripheral) Single-supply 3.3V device with tolerant Commercial Industrial temperature ranges INTRODUCTION AX30NDIxxPHY devices Network Device Interfaces compliant Generation IntelliBus protocol. These devices allow efficient connection variety peripheral devices onto multi-point IntelliBus network. Peripheral devices include converters data acquisition, audio video DACs multimedia digital basic control sense applications.
IntelliBus Network
MLVDS
IntelliBus Interface
IntelliBus Data
Memory Interface
Command Decoder
Channel Interface
UART
External Serial Flash
Trig/ Sync
Boot
Clock Generation,
Clks
Config/ Control Signals
Remote Input Clock
AX030NDI-05PHY: Channel thru only AX030NDI-02PHY: Channel only
Figure AX30NDI-09PHY Block Diagram
IntelliBus Interface Data rates 7.5Mbps, 15Mbps 30Mbps userselectable bit-rate select control inputs AX30NDIxxPHY. internal transceiver provides layer signaling. internal Command Decoder interprets network IntelliBus commands from Network Interface Controller, performs appropriate data transfer peripheral control. External Serial Flash Interface AX30NDIxxPHY device contains bootup algorithm support unique unique self-configuration port. This bootup data stored external flash, downloaded power-up into internal serial interface. Electronic Data Sheet information also stored external flash available access IntelliBus Network Interface Controller after bootup procedure downloads data RAM. flash interface implemented standard interface. Peripheral Interface (Ports) number available ports device type defined Table three family members AX30NDIxxPHY differ only number ports, thus affecting package size. Each port supports protocol. shown AX30NDI-09PHY Block Diagram, alternate serial protocols supported: I2C, UART. These alternate modes user selected tie-offs. Each port contains three FIFOs buffering data flow. 16-word Output FIFO stores network data before transferring peripheral when proper (optionally isochronous) IntelliBus command decoded.
16-word Input Buffer second 16-word Input FIFO provided allow isochronous data collection peripheral data rates, with previous-frame data output IntelliBus network IntelliBus data rates. Isochronous timedeterministic data transfers from each port supported Trigger Sync signals, decoded from IntelliBus network commands. internal AX30NDIxxPHY provides peripheral clocking which locked Trigger signal. Three user-defined frequencies available channels, ranging from 24.576 MHz. Remote Inputs AX30NDIxxPHY contains support inputs which read IntelliBus Network Interface Controller determine physical location each located bus. These signals discrete inputs tied externally Ground. Table AX03NDI Packaging
Part AX30NDI-02PHY-Q72 AX30NDI-02PHY-B72 AX30NDI-05PHY-L120 AX30NDI-05PHY-B121 AX30NDI-09PHY-B169 Channel Package Type 72-pin 72-pin FBGA 120-pin LQFP 121-pin FBGA 169-pin FBGA Dim. (mm)
COLORADO Toll Free: 800-645-8862 Fax: 719-594-8468 MID-ATLANTIC Tel: 321-951-4164 Fax: 321-951-4254
INTERNATIONAL Tel: 805-778-9229 Fax: 805-778-1980 WEST COAST Tel: 949-362-2260 Fax: 949-362-2266
NORTHEAST Tel: 603-888-3975 Fax: 603-888-4585 CENTRAL Tel: 719-594-8017 Fax: 719-594-8468
www.aeroflex.com
info-ams@aeroflex.com
Aeroflex Colorado Springs, Inc., reserves right make changes products services herein time without notice. Consult Aeroflex authorized sales representative verify that information this data sheet current before using this product. Aeroflex does assume responsibility liability arising application product service described herein, except expressly agreed writing Aeroflex; does purchase, lease, product service from Aeroflex convey license under patent rights, copyrights, trademark rights, other intellectual rights Aeroflex third parties.
passion performance defined three attributes represented these three icons: solution-minded, performance-driven customer-focused
Mixed-Signal ASIC Products
AX30NDI-10/06/03 Network Interface Device (NDI) Bridge with IntelliBusProtocol
Preliminary Datasheet 2005 www.aeroflex.com/MixedSignal
FEATURES Network Device Interface (NDI) designed specifically for: Factory Floor Automation applications In-Vehicle Health Monitoring applications Compliant IntelliBus Standards Generation Protocol Full IntelliBus data rates 7.5, Mbps (pinselectable) Integrated CAN2.0B controller interface provides IntelliBus-to-CAN network bridge IntelliBus network connection through simple MLVDS RS-485 external transceiver device bootup memory supported words external serial flash Configurable internal generates multiple isochronous peripheral clocks 24.576 MHz)
Variety serial connections peripherals: SPI, I2S, UART 16-word output FIFO channel peripheral) Dual 16-word input FIFOs channel (from peripheral) Single-supply 3.3V device with tolerant Variety package sizes: 3channel variants Commercial Industrial temperature ranges INTRODUCTION AX30NDIxxCAN devices Network Device Interfaces compliant Generation IntelliBus protocol. These devices allow efficient connection variety peripheral devices, including CAN, onto multi-point IntelliBus network. Peripheral devices include converters data acquisition, audio video DACs multimedia digital basic control sense applications plus data.
IntelliBus Network
LVTTL IntelliBus Interface
IntelliBus Data
Config/Control Signals
Remote
Memory Interface
Command Decoder
Channel Interface
UART
External Serial Flash
Trig/ Sync
Boot
Clock Generation,
Clks
Input Clock CAN2.0B
CANH CANL
AX030NDI-06CAN: Channel thru only AX030NDX-03CAN: Channel only
Figure AX30NDI-10CAN Block Diagram
IntelliBus Interface Data rates 7.5Mbps, 15Mbps 30Mbps userselectable bit-rate select control inputs AX30NDIxxCAN. simple MLVDS RS-485 external transceiver required layer. internal Command Decoder interprets network IntelliBus commands from Network Interface Controller, performs appropriate data transfer peripheral control. External Serial Flash Interface AX30NDIxxCAN device contains bootup algorithm support unique unique self-configuration port. This bootup data stored external flash, downloaded power-up into internal serial interface. Electronic Data Sheet information also stored external flash available access IntelliBus Network Interface Controller after bootup procedure downloads data RAM. flash interface implemented standard interface. Peripheral Interface (Ports) number available ports device type defined Table three family members AX30NDIxxCAN differ only number ports, thus affecting package size. Each port supports protocol. shown AX30NDI-010CAN Block Diagram, alternate serial protocols supported: I2C, UART. These alternate modes user selected tie-offs. Each port contains three FIFOs buffering data flow. 16-word Output FIFO stores network data before transferring peripheral when proper (optionally isochronous) IntelliBus command decoded.
16-word Input Buffer second 16-word Input FIFO provided allow isochronous data collection peripheral data rates, with previous-frame data output IntelliBus network IntelliBus data rates. Isochronous timedeterministic data transfers from each port supported Trigger Sync signals, decoded from IntelliBus network commands. internal AX30NDI provides peripheral clocking which locked Trigger signal. Three user-defined frequencies available channels, ranging from 24.576 MHz. Remote Inputs AX30NDIxxCAN contains support inputs which read IntelliBus Network Interface Controller determine physical location each located bus. These signals discrete inputs tied externally Ground. Interface AX30NDIxxCAN contains controller module implementing bridge between IntelliBus network 2.0B network. Table AX03NDI Packaging
Part AX30NDI-03CAN-Q72 AX30NDI-03CAN-B72 AX30NDI-06CAN-L120 AX30NDI-06CAN-B121 Channel Package Type 72-pin 72-pin FBGA 120-pin LQFP 121-pin FBGA Pkg. Dim. (mm)
COLORADO Toll Free: 800-645-8862 Fax: 719-594-8468 MID-ATLANTIC Tel: 321-951-4164 Fax: 321-951-4254
INTERNATIONAL Tel: 805-778-9229 Fax: 805-778-1980 WEST COAST Tel: 949-362-2260 Fax: 949-362-2266
NORTHEAST Tel: 603-888-3975 Fax: 603-888-4585 CENTRAL Tel: 719-594-8017 Fax: 719-594-8468
www.aeroflex.com
info-ams@aeroflex.com
Aeroflex Colorado Springs, Inc., reserves right make changes products services herein time without notice. Consult Aeroflex authorized sales representative verify that information this data sheet current before using this product. Aeroflex does assume responsibility liability arising application product service described herein, except expressly agreed writing Aeroflex; does purchase, lease, product service from Aeroflex convey license under patent rights, copyrights, trademark rights, other intellectual rights Aeroflex third parties.
passion performance defined three attributes represented these three icons: solution-minded, performance-driven customer-focused
Other recent searches
SIIGX51005-1 - SIIGX51005-1 SIIGX51005-1 Datasheet
Si1102 - Si1102 Si1102 Datasheet
PM8315 - PM8315 PM8315 Datasheet
PM8315 - PM8315 PM8315 Datasheet
PM4328 - PM4328 PM4328 Datasheet
PM5365 - PM5365 PM5365 Datasheet
PDB-V448-46 - PDB-V448-46 PDB-V448-46 Datasheet
MCR100 - MCR100 MCR100 Datasheet
MC145011 - MC145011 MC145011 Datasheet
DF3A6 - DF3A6 DF3A6 Datasheet
Privacy Policy | Disclaimer
© 2012 Datasheet Archive
