3624.2 Power, High Performance Radiation Hardened Operational Amp

The Datasheet Archive - 100 Million Datasheets from 7500 Manufacturers.

3624.2 Power, High Performance Radiation Hardened Operational Amp

Datasheet Thumbnail

Top Searches for this datasheet

HS-2700RH
3624.2
Power, High Performance Radiation Hardened Operational Amplifier
HS-2700RH radiation hardened internally compensated operational amplifiers which employ dielectric isolation achieve excellent dynamic performance with very quiescent power consumption. performance amplifier input characterized high CMRR (106dB), offset voltage (0.5mV), along with bias offset current (5.0nA 2.5nA respectively). These input specifications, conjunction with offset null capability open-loop gain 300,000V/V, enable HS-2700RH provide accurate, high-gain signal amplification. Gain bandwidth 1MHz slew rate 20V/µs allow processing fast, wideband signals. Input output signal amplitudes least ±11V accommodated while providing output drive capability 10mA. maximum reliability, output protected event short circuits ground. amplifier operates from wide range supplies (±5.5V ±20V) with maximum quiescent supply drain only 150µA. HS-2700RH therefore, ideally suited low-power instrumentation filtering applications that require fast, accurate response over wide range signal frequency. Specifications Hard devices controlled Defense Supply Center Columbus (DSCC). numbers listed here must used when ordering. Detailed Electrical Specifications these devices contained 5962-95670. "hot-link" provided homepage downloading.
Features
Electrically Screened 5962-95670 Qualified MIL-PRF-38535 Requirements Power Supply Current 150µA (Max) 90µA (Typ) High CMRR 86dB (Min) 106dB (Typ) Input Bias Current 20nA (Min) (Typ) Offset Current 10nA (Min) 2.5nA (Typ) Total Dose RAD(Si)
Applications
High Gain Amplifier Instrumentation Amplifiers Active Filters Telemetry Systems Battery-Powered Equipment
Ordering Information
ORDERING NUMBER 5962D9567002VCA 5962D9567002VCC 5962D9567002VGA INTERNAL MKT. NUMBER HS1-2700RH-Q HS1B-2700RH-Q HS2-2700RH-Q TEMP. RANGE (oC)
Pinouts
HS1-2700RH (CERDIP) GDIP1-T14 HS1B-2700RH (SBDIP) CDIP2-T14 VIEW
GUARD
HS2-2700RH (CAN) MACY1-X8 VIEW
GUARD
OUTPUT
CAUTION: These devices sensitive electrostatic discharge; follow proper Handling Procedures. www.intersil.com 407-727-9207 Copyright Intersil Corporation 1999
HS-2700RH Test Circuit
ACOUT OPEN OPEN OPEN -VEE 1.6K +VCC 75pF (NOTE) -1/10
LOOP STABILITY, VALUE CAPACITOR PREVENT OSCILLATION
OPEN
EOUT RESISTORS CAPACITORS ±10% (µF) BUFFER 500K OPEN
OPEN
NOTE: Includes stray capacitances.
Timing Waveforms
VOUT
1.6K
75pF
FIGURE SIMPLIFIED TEST CIRCUIT
+1.0V INPUT INPUT
+40mV
-1.0V +2.5V OUTPUT -2.5V SLEW RATE
OVERSHOOT +160mV OUTPUT RISE TIME
-40mV
FIGURE SLEW RATE WAVEFORM
FIGURE TRANSIENT RESPONSE WAVEFORM
NOTE: Measured both positive negative transitions. Capacitance Compensation should minimized.
HS-2700RH Typical Performance Curves
CURRENT (mA) VOLTAGE (mV) BIAS CURRENT
25oC, VSUPPLY ±15V, Unless Otherwise Specified
OFFSET CURRENT
TEMPERATURE (oC)
TEMPERATURE (oC)
FIGURE OFFSET VOLTAGE FUNCTION TEMPERATURE
FIGURE INPUT BIAS CURRENT OFFSET CURRENT FUNCTION TEMPERATURE
BIAS CURRENT (nA) -100 -200 -300 -400 -500 ±15.0V 25oC BIAS CURRENT (µA)
COMMON MODE VOLTAGE ±15.0V 25oC
DIFFERENTIAL INPUT VOLTAGE
FIGURE BIAS CURRENT FUNCTION COMMON MODE VOLTAGE
FIGURE BIAS CURRENT FUNCTION DIFFERENTIAL INPUT VOLTAGE
1000 POWER SUPPLY CURRENT (µA)
±15.0V POWER SUPPLY CURRENT (µA) 25oC
±20.0V ±15.0V ±10.0V ±5.5V
DIFFERENTIAL INPUT VOLTAGE (mV)
TEMPERATURE (oC)
FIGURE POWER SUPPLY CURRENT FUNCTION DIFFERENTIAL INPUT VOLTAGE
FIGURE POWER SUPPLY CURRENT FUNCTION TEMPERATURE
HS-2700RH Typical Performance Curves
25oC, VSUPPLY ±15V, Unless Otherwise Specified (Continued)
GAIN (dB)
±20.0V ±15.0V ±10.0V ±5.5V
TEMPERATURE (oC)
FIGURE VOLTAGE GAIN FUNCTION TEMPERATURE NOTE: Open loop (comparator) applications recommended, because above characteristic.
Burn-In Circuits
HS1-2700RH CERDIP HS2-2700RH METAL
NOTES: ±5%, 1/4W (Min) 0.01µF/Socket (Min) 0.1µF/Row (Min) 1N4002 equivalent (per board) |(V+) (V-)|
NOTES: ±5%, 1/4W (Min) 0.01µF/Socket (Min) 0.01µF/Socket (Min) 0.1µF/Row (Min) 1N4002 equivalent (per board) |(V+) (V-)| Insulated scope probe must used during board check-out.
HS-2700RH Irradiation Circuit
NOTES: ±5%, 1/4W +15V 1.0V -15V 1.0V
Schematic Diagram
OSV1
430K
NOTE: Nominal currents shown microamperes.
HS-2700RH Characteristics
DIMENSIONS: mils mils mils (1780µm 1530µm 1530µm) INTERFACE MATERIALS: Glassivation: Type: Nitride Thickness: Metallization: Type: Aluminum Thickness: Substrate: Linear Bipolar, Backside Finish: Silicon ASSEMBLY RELATED INFORMATION: Substrate Potential (Powered Up): Unbiased ADDITIONAL INFORMATION: Worst Case Current Density: A/cm2
Metallization Mask Layout
HS-2700RH
OUTPUT
Intersil semiconductor products manufactured, assembled tested under ISO9000 quality systems certification.
Intersil semiconductor products sold description only. Intersil Corporation reserves right make changes circuit design and/or specifications time without notice. Accordingly, reader cautioned verify that data sheets current before placing orders. Information furnished Intersil believed accurate reliable. However, responsibility assumed Intersil subsidiaries use; infringements patents other rights third parties which result from use. license granted implication otherwise under patent patent rights Intersil subsidiaries.
information regarding Intersil Corporation products, site http://www.intersil.com

3624.2 Power, High Performance Radiation Hardened Operational Amp

Top Searches for this datasheet

Other recent searches